swACLIpv6RuleAccessID
ACLMGMT-MIB ·
.1.3.6.1.4.1.171.12.9.3.4.1.2
Object
column
Integer32
The ID of the ACL rule entry relates to swACLIpv6RuleProfileID. When row creation is set to 0, this indicates the access ID will be assigned automatically for the ports in the swACLIpv6RulePort to create rule entries for swACLIpv6RulePort accordingly. Set to 1-65535 indicates creation of an access ID for the swACLIpv6RulePort. The swACLIpv6RulePort must be set to one port only, otherwise the row creation will fail.
Context
- MIB
- ACLMGMT-MIB
- OID
.1.3.6.1.4.1.171.12.9.3.4.1.2- Type
- column
- Access
- readonly
- Status
- current
- Parent
- swACLIpv6RuleEntry
- Table
- swACLIpv6RuleTable
- Siblings
- 25
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-65535
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| swACLIpv6RuleProfileID The ID of the ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.1 |
| swACLIpv6RulePermit This object indicates if the result of the packet examination is 'permit' or 'deny'.
The default is 'permit'.
permit - Specifies that packets matching the access profile are
… | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.10 |
| swACLIpv6RulePort Specifies that the access rule will apply only to port(s).
This object and swACLIpv6RuleVID can not be set together. | column | PortList | .1.3.6.1.4.1.171.12.9.3.4.1.11 |
| swACLIpv6RuleRowStatus This object indicates the status of this entry. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.171.12.9.3.4.1.12 |
| swACLIpv6RuleOwner The owner of the ACL rule entry. Only owners can modify this entry. | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.13 |
| swACLIpv6RuleRxRate Specifies the rx-rate, 0 denotes no_limit. The maximum value of this object depends on the device. | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.14 |
| swACLIpv6RuleEnableReplaceDscp Specifies if the switch will change priorities of packets that match the access profile
DSCP field or not.
Replace DSCP and replace ToS precedence can not both be supported. | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.15 |
| swACLIpv6RuleRepDscp Specifies a value to be written to the DSCP field of an incoming packet
that meets the criteria specified in the first part of the command.
This value will over-write the value in… | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.16 |
| swACLIpv6RuleEnableReplaceTosPrecedence Specifies if the switch will change priorities of packets that match the access profile
ToS precedence field or not.
Replace DSCP and replace ToS precedence can not both be suppor… | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.17 |
| swACLIpv6RuleRepTosPrecedence Specifies a value to be written to the ToS precedence field of an incoming packet
that meets the criteria specified in the first part of the command.
This value will over-write th… | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.18 |
| swACLIpv6RuleVID Specifies this rule only applies to the specified VLAN. There are two conditions:
1.only the portlist that belongs to this VLAN will be included;
2.packets must belong to this VLA… | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.19 |
| swACLIpv6RuleProtocol Specifies the IPv6 protocol.
For some older chips, this object can not be set. When getting this object,
it always returns the type which has been configured in swACLIpv6Entry.
… | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.20 |
| swACLIpv6RuleSrcPort Specifies that the rule applies to the range of the TCP/UDP source ports. | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.21 |
| swACLIpv6RuleDstPort Specifies the TCP/UDP destination ports range. | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.22 |
| swACLIpv6RuleMaskSrcIpv6Addr Specifies that the per rule mask of swACLIpv6RuleSrcIpv6Addr.
This should be a 16 byte octet string.
The value of this object when not in use is the corresponding mask in the prof… | column | Ipv6Address | .1.3.6.1.4.1.171.12.9.3.4.1.23 |
| swACLIpv6RuleMaskDstIpv6Addr Specifies that the rule applies to the destination IPv6 address.
This should be a 16 byte octet string. | column | Ipv6Address | .1.3.6.1.4.1.171.12.9.3.4.1.24 |
| swACLIpv6RuleMaskSrcPort Specifies that the per rule mask of swACLIpv6RuleSrcPort.
The value of this object when not in use is the corresponding mask in the profile mask.
Once the value of this object is … | column | OctetString | .1.3.6.1.4.1.171.12.9.3.4.1.25 |
| swACLIpv6RuleMaskDstPort Specifies the per rule mask of swACLIpv6RuleDstPort.
The value of this object when not in use is the corresponding mask in the profile mask.
Once the value of this object is modif… | column | OctetString | .1.3.6.1.4.1.171.12.9.3.4.1.26 |
| swACLIpv6RuleClass Specifies that the rule applies to the IPv6 class field. | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.3 |
| swACLIpv6RuleFlowlabel Specifies that the rule applies to the IPv6 flow label field. | column | OctetString | .1.3.6.1.4.1.171.12.9.3.4.1.4 |
| swACLIpv6RuleSrcIpv6Addr Specifies that the rule applies to the source IPv6 address.
This should be a 16 byte octet string. | column | Ipv6Address | .1.3.6.1.4.1.171.12.9.3.4.1.5 |
| swACLIpv6RuleDstIpv6Addr Specifies that the rule applies to the destination IPv6 address.
This should be a 16 byte octet string. | column | Ipv6Address | .1.3.6.1.4.1.171.12.9.3.4.1.6 |
| swACLIpv6RuleEnablePriority Specifies that the access rule will apply only to packets with
priority value. | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.7 |
| swACLIpv6RulePriority Specifies the priority will change in packets while the swACLIpv6RuleReplacePriority
is enabled. | column | Integer32 | .1.3.6.1.4.1.171.12.9.3.4.1.8 |
| swACLIpv6RuleReplacePriority Specifies if the switch will change priorities of packets that match the access profile
802.1p priority tag or not. | column | Enumeration | .1.3.6.1.4.1.171.12.9.3.4.1.9 |