prtTestCmdAndStatus

ACE202-MIB · .1.3.6.1.4.1.164.6.2.15.4.1.1.2
MIB view Table view

Object

column r/w SNMPv2-SMIInteger32 
Setting this object to a value as detailed further on 
(except 0) will initiate a test on the specific port. 
The test/s requested will be set according to the respective
bit. The value of this object will be a sum of (2**n), where n is
the Bit:
  TEST                  BIT	                     VALUE
 -----------            ---						------
 reserved                0						   1
		PayloadLoop=RLB     	1 (=Remote Loopback)	   2
 LineLoop=DIG            2 (=Digital)			   4
 OtherLoop               3						   8
 InwardLoop=LLB          4 (=Local Loopback)       16
 BERT                    5						  32
 LC                      6                         64
		ToneInjection			7						 128
              		
              
 e.g : If the requested value is 20 -> 010100  ->
       Bits 2 & 4 are set -> the requested tests are :
                             LineLoopback=DIG
                             InwardLoopback=LLB
                                             
Not all tests combinations are valid.
	   For valid test combination, see each product's specification.
              
The terminology and order of tests (except BERT) is according to 
	   the one used for Test Status of DS1 and DS3 standards.
	   The notations : RLB, LLB, DIG are the most used in RAD's products, but they 
	   can be different. For exact definition see product's spec. 
              
Setting this object to stop (value=0 ; all bits are 0), 
will stop all the user requested tests running on the 
selected port.
              
When no test is running on the port, the Get value (test status)
	   will be 0.
              
	   PayloadLoop=RLB
	     The received signal at this interface is looped
	     through the device.  Typically the received signal
	     is looped back for retransmission after it has
	     passed through the device's framing function.
              
	   LineLoop=DIG
	     The received signal at this interface does not
	     go through the device (minimum penetration) but
	     is looped back out.
              
	   OtherLoop
	     Loopbacks that are not defined here.
              
	   InwardLoop=LLB 
	     The sent signal at this interface is looped back
	     through the device.
              
	   LC
	     This loop is applicable only for HSSI interface, towards the router .
              
	   ToneInjection
		 This loop is applicable for analog voice (like FXS).

Context

MIB
ACE202-MIB
OID
.1.3.6.1.4.1.164.6.2.15.4.1.1.2
Type
column
Access
readwrite
Status
current
Parent
prtTestEntry
Table
prtTestTable
Siblings
3

Syntax

SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
prtTestIdx
This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.164.6.2.15.4.1.1.1
prtBertCounter
This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counte…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.164.6.2.15.4.1.1.3
prtTestInitiator
This object indicates who initiated this port's test/s.
columnEnumeration.1.3.6.1.4.1.164.6.2.15.4.1.1.4