dsx1Scramble

ACE202-MIB · .1.3.6.1.4.1.164.3.1.6.4.2.1.9

MIB view Table view

Object

column r/w Enumeration

Scrambling is an operation that randomizes the bits 
of the payload of the ATM cell by a polynom.
This operation helps with the error detection mechanism
of the HEC. Not applicable for E1.
active - will scramble/descramble the payload ATM cell
notactive - will not scramble/descramble.

Context

MIB: ACE202-MIB
OID: .1.3.6.1.4.1.164.3.1.6.4.2.1.9
Type: column
Access: readwrite
Status: current
Parent: dsx1XConfigEntry
Table: dsx1XConfigTable
Siblings: 13

Syntax

Enumeration

Values & Constraints

Object Constraints

range: 4-4

Related Objects

Sibling Objects

Object	Type	Syntax	OID
dsx1IdleCode Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.1`
dsx1LineAdaptiveTimingMode Enables end to end clock synchronization. Default value - off.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.10`
dsx1TxClockSource The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock s…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.11`
dsx1AisEnable Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.12`
dsx1TsEchoCancel This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follows: First octet bit'0'=not in use bit'1'= TS#1, bit'7' = TS#7, .. 2nd octet …	column	OctetString	`.1.3.6.1.4.1.164.3.1.6.4.2.1.13`
dsx1EchoCancelerModule This parameter indicates whether echo-cancellation module exists for this line.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.14`
dsx1LineMode T1 device operation mode. Valid for T1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.2`
dsx1dBTxGain Transmit line Gain for T1 CSU line mode.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.3`
dsx1RxSensitivity Determine the maximum attenuation of the receive signal that can be compensated for by the interface receive path. Not applicable for T1.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.4`
dsx1RestoreTime Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.5`
dsx1TcFirstSignal Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. Valid for T1 only.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.6`
dsx1TcSignal Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.7`
dsx1TcPattern Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.8`