prtTestCmdAndStatus

Object

column r/w SNMPv2-SMIInteger32

Setting this object to a value as detailed further on 
(except 0) will initiate a test on the specific port. 
The test/s requested will be set according to the respective
bit. The value of this object will be a sum of (2**n), where n is
the Bit:
  TEST                  BIT	                     VALUE
 -----------            ---						------
 reserved                0						   1
		PayloadLoop=RLB     	1 (=Remote Loopback)	   2
 LineLoop=DIG            2 (=Digital)			   4
 OtherLoop               3						   8
 InwardLoop=LLB          4 (=Local Loopback)       16
 BERT                    5						  32
 LC                      6                         64
		ToneInjection			7						 128
		Inband 				    8			   			 256
              
 e.g : If the requested value is 20 -> 010100  ->
       Bits 2 & 4 are set -> the requested tests are :
                             LineLoopback=DIG
                             InwardLoopback=LLB
                                             
Not all tests combinations are valid.
	   For valid test combination, see each product's specification.
	   For LRS52, only single test is allowed simultaneously
              
The terminology and order of the first tests (except BERT) 
is according to the one used for Test Status of DS1 and DS3 standards.
	   The notations : RLB, LLB, DIG are the most used in RAD's products, but they 
	   can be different. For exact definition see product's spec. 
              
Setting this object to stop (value=0 ; all bits are 0), 
will stop all the user requested tests running on the 
selected port.
              
When no test is running on the port, the Get value (test status)
	   will be 0.
              
	   PayloadLoop=RLB
	     The received signal at this interface is looped
	     through the device.  Typically the received signal
	     is looped back for retransmission after it has
	     passed through the device's framing function.
              
	   LineLoop=DIG
	     The received signal at this interface does not
	     go through the device (minimum penetration) but
	     is looped back out.
              
	   OtherLoop
	     Loopbacks that are not defined here.
              
	   InwardLoop=LLB 
	     The sent signal at this interface is looped back
	     through the device.
              
	   LC
	     This loop is applicable only for HSSI interface, towards the router .
              	   
	   ToneInjection
		 This loop is applicable for analog voice (like FXS).

Context

MIB: ACE2002-MIB
OID: .1.3.6.1.4.1.164.6.2.15.4.1.1.2
Type: column
Access: readwrite
Status: current
Parent: prtTestEntry
Table: prtTestTable
Siblings: 4

Related Objects

Sibling Objects

Object	Type	Syntax	OID
prtTestIdx This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.6.2.15.4.1.1.1`
prtBertCounter This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counte…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.6.2.15.4.1.1.3`
prtTestInitiator This object indicates who initiated this port's test/s.	column	Enumeration	`.1.3.6.1.4.1.164.6.2.15.4.1.1.4`
prtTestTimeout This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. When the timeout expires, the test is stopped. Value of 0 indi…	column	Integer32	`.1.3.6.1.4.1.164.6.2.15.4.1.1.5`

Indexes

Object

Context

Syntax

Values & Constraints

Related Objects