a3ComBrgSrcSecCtl
A3Com-Bridge-r3-MIB ·
.1.3.6.1.4.1.43.2.9.1.12.1.4
Object
column
mandatory
r/w
Enumeration
This object is a security feature that allows the control of packets sent from specific source addresses. If this object is set to forward (2), this port will forward only those packets sent from addresses listed in the static forwarding table for this port. If this object is set to block, this port will block every packet sent by a station whose address is listed in the static forwarding table for this port. Note, these actions are taken by this port after it receives a packet from the network. This does not apply to packets it forwards to the network.
Context
- MIB
- A3Com-Bridge-r3-MIB
- OID
.1.3.6.1.4.1.43.2.9.1.12.1.4- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- a3ComBrgPortEntry
- Table
- a3ComBrgPortTable
- Siblings
- 10
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | none |
2 | forward |
3 | block |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| a3ComBrgPortIndex mandatory The port number of the port for which this
entry contains bridge management information. | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.1 |
| a3ComBrgSmdsGroupAddr mandatory This identifies the SMDS Group Address that
is used by the bridge to transmit packets to
all the other bridges identified by this SMDS
Group Address. This address is used as the … | column | SMDSAddress | .1.3.6.1.4.1.43.2.9.1.12.1.10 |
| a3ComBrgX25ProfId mandatory This object specifies the X25 User ProfileID to be used for
selecting a Virtual Circuit to send Bridged Packets. Range
is 0..255. If the value specified is 0 then use the DTE Prof… | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.14 |
| a3ComBrgPortCtl mandatory This object controls which type(s) of packets
are bridged. This has no affect on whether the
bridge participates in either the Spanning Tree
or Source Route Protocols. | column | Enumeration | .1.3.6.1.4.1.43.2.9.1.12.1.2 |
| a3ComBrgDstSecCtl mandatory This object is a security feature that allows the
control of packets sent to specific destinations.
If this object is set to forward (2), only those
packets for destination addres… | column | Enumeration | .1.3.6.1.4.1.43.2.9.1.12.1.3 |
| a3ComBrgX25Pid mandatory This object applies to transparent bridging
over an X25 network. It specifies the protocol
ID to be used in an outgoing X25 call. | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.5 |
| a3ComBrgX25Qsize obsolete This object applies to transparent bridging
over an X25 network. It allows the specification
of the maximum number of packets that can be
queued on any single virtual circuit to… | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.6 |
| a3ComBrgX25VcLimit obsolete This object allows the specification of the
maximum number of virtual circuits to a
specific DTE that can be established concurrently
for transparent bridging over an x25 networ… | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.7 |
| a3ComBrgX25VcTimer obsolete This object specifies the maximum amount of
time, in minutes, that can elapse when there
is no activity on the x25 virtual circuit to a DTE
before it is cleared.
NO… | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.8 |
| a3ComBrgBroadCastLimit mandatory This object specifies the maximum rate, in
packets per second, at which broadcast and
multicast packets are forwarded through this
port. If the number of these packets during
a … | column | Integer32 | .1.3.6.1.4.1.43.2.9.1.12.1.9 |