A Sonus SBC Application service was restarted.

System detected a problem during previous boot cycle, active partition has switched automatically. Suggested action - backup the configuration and re-apply the upgrade to the currently inactive partition.

While booting, one of the partition could not be mounted. Likely a eUSB corruption. Contact Sonus TAC with the information in this alarm.

Failed to set active partition.Contact Sonus TAC with the information in this alarm.

Attempt to auto repair boot parmeters failed.Contact Sonus TAC with the information in this alarm.

Boot parameter mismatch was detected.Attempting to auto repair.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

System up after planned restart.

System up after unplanned restart.

No response to seizure.

Remote end did not back off in glare.

Wink expected, did not arrive.

Event of off-hook did not produce dial tone as expected.

CAS signaling group disabled.

Call attempted but CAS feature is not enabled. This alarm is cleared by CAS license enabled event.

License manager notify CAS that license is enabled.

Wink failure had occurred, but wink is received now.

No Dial Tone was received, but Dial Tone is received now.

No Response to seizure was received, but Response is received now.

Invalid character(s) removed, correct issue and delete warning.

Invalid character(s) removed, correct issue and delete warning.

CAS signaling group enabled.

CAS-R2 CD Bits are mismatched.

CAS-R2 CD Bits are now matching.

Network glare occured on this interface.

Config validation failure during startup. Please check the configuration.

A Card was detected with invalid Card ID EEPROM contents (failed CRC-CCITT check). Suggested action - provide the entire alarm message including the numbers at the end to Sonus TAC for further assistance.

During Line Card activation, a Card Fault was detected after power was applied to the card. The Card will remain out-of-service.  Suggested action - reboot system. If issue persists, contact Sonus TAC with the alarm information.

A Card was detected which can be identified, but the Sonus SBC system software is unable to support. The Card will remain out-of-service. Suggested action - reboot system. If issue persists, contact Sonus TAC with the alarm information.

A Power supply module has indicated a failure of input power. The Sonus SBC System has lost Power Supply redundancy. Suggested action - Verify that the power cable is connected and that the PS is functioning properly.

A Power Supply module has indicated that input power has been restored. This event clears the 'Power Supply Input Failure' Alarm.

A Power Supply module has indicated a failure of output power. The Sonus SBC System has lost Power Supply redundancy. Suggested action - Verify that the PS is functioning properly.

Check the System tab to find the Fan ID of the failed fan. Contact Sonus TAC with this information.

Check the System tab to find the Fan ID's of the failed fans. Contact Sonus TAC with this information.

The temperature sensors have indicated that the system is running warm (65°C threshold).

The temperature sensors have indicated that the system is no longer running warm (55°C threshold). This event clears the 'System Temperature Warm' Alarm.

The temperature sensors have indicated that system is running hot.

The temperature sensors have indicated that the system is no longer running hot (65°C threshold). This event clears the 'System Temperature Hot' Alarm.

License of the node has expired, all the licensed features would fail to work. Contact Sonus Enterprise Sales.

License of the node will expire in 2 weeks.

New License is applied on the node.

Either an invalid key is used, or the license key applies to a different node, or the license key expiry is past the present date. Contact Sonus Sales to obtain a new license.

The alarm is generated when the required license is not available.  Check the number of licensed SIP or TDM channels, the number of SIP registrations, SBA, Transcoding or AD. Suggested action - obtain license for missing functionality.

ASM system can not be reached, system is down. Check whether the ASM is rebooting.

Clears alarm 'ASM Unreachable'.

ASM system was previously unreachable, but has come up. This alarm doesn't autoclear so the user can investigate the cause, but the system should be working correctly now.

ASM services are not running, calls through the ASM cannot be placed.

Clears alarm 'ASM Services Not Running'.

ASM Services Recovered.

The system attempted to restart a failed service on the ASM, service did not start successfully. User interaction is required.

This event is set when the SBA communication system is first established, and usually indicates that the Application Solution Module (ASM) has finished booting. It should come up at system startup, it may come again if the ASM hardware is rebooted.

A planned or deliberate shut down is taking place on the Application Solution Module (ASM).

Ethernet port specified has lost link. Source Instance: Eth0/Eth1 via SBA Monitor.

Ethernet port specific has recovered link.

The ASM and Sonus SBC IP interfaces are in different subnets and cannot communicate.

The ASM and Sonus SBC IP interfaces are in the same subnet and can now communicate.

There is an action set table number/name that should be printed with this event.

There is a normalization table number/name that should be printed with this event.

There is a route table number/name that should be printed with this event.

There is a transformation table number/name that should be printed with this event.

This alarm is set if a link is down or some other event has occured to take a route entry out of service.

Route came up.

A call with destination of X tried to be forked more than the limit allows (currently 8).

A call with a destination of X was forked with no forking license available.

A call with with destination of X tried to execute InvokeActionSet more the the limit allows (currently 10).

There is a PSAP Callback table number/name that should be printed with this event.

Channel is up and is in service. This clears the 'Channel out of service' alarm.

Channel Out Of Service Alarm. This alarm is automatically cleared when Channel is in service.

Emergency Call is Attempted from Calling Number, Calling Extension, Caller IP address.

Emergency Call Alarm will be cleared after expiry time in emergency status table.

SIP server has failed to respond and has been taken out of service. This alarm will be cleared by the event 'SIP server became responsive'.

All servers in SG have failed.This alarm will be cleared by 'SIP Signaling group enabled' event.

Configuration action has changed this Signaling Group from Enabled to Disabled.

This alarm is generated if TLS Connection failed with an Alert. The connection associated with a TLS Connection ID is aborted. Suggested action - look up the TLS Alert code definitions and determine what corrective actions are to be taken.

There was long period of inactivity during exchange of handshake messages for an associated TLS Connection ID. Suggested action - if network delays is experienced, tune the configurable timeout value as to set it to maximum 30 seconds.

Discrepancy of an FQDN/Port configured in the SipServer object that is different than the DNS SRV lookup. A DNS SRV record can return the port number for the selected protocol. The DNS SRV port value will take priority over the configured port.

SIP server came up.

SIP cluster went down.This is due to all the servers in the clusters are not responsive. This alarm will be cleared by the event 'Sip cluster enabled'.

SIP cluster enabled.

SIP Signaling group enabled.

Failed to resolve the FQDN entries in the SIP Signaling Group. Suggested action - check the FQDN syntax.

Successfully resolved the FQDN of the SIP Signaling group.

Failed to resolve the SIP server FQDN entries in the SIP Server table. Suggested action - check the FQDN syntax.

SIP Server config FQDN resolved.

Failed to resolve an FQDN with DNS server during a SIP call session.