SUPERMICRO-PROVIDERBRIDGE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
17
Rows
17
Columns
70

fsPbPortInfoTable

table
.1.3.6.1.4.1.10876.101.1.113.2.1 · 1 row entry · 10 columns
Open in standard view 
A table containing provider bridge releated 
configurations for the externally accessible ports.
          
All the objects in this table are applicable 
only when the Bridge Mode is set as ProviderBridge or 
ProviderCoreBridge or ProviderEdgeBridge.
fsPbPortInfoEntry entry .1.3.6.1.4.1.10876.101.1.113.2.1.1
Each entry in this table specifies the Provider Bridge related
port configurations. This table is indexed by ifIndex.
Indexes
fsPbPort
Column Syntax OID
fsPbPort
The Index value of the port in the system for which this entry
applies. The maximum index value of the port is defined by the
system.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.1
fsPbPortSVlanClassificationMethod
This object indicates the type of SVLAN classification that has to be used
for a given type of port.

providerNetworkPort / customerNetworkPort - Port's 'pvid' will be the
SVLAN classification for the un…
Enumerationr/w
Enumerated Values:
1sourceMac
2destinationMac
3cvlanSrcMac
4cvlanDstMac
5dscp
6cvlanDscp
7sourceIp
8destinationIp
9srcIpDstIp
10cvlanDstIp
11cvlan
12pvid
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.2
fsPbPortSVlanIngressEtherType
This object indicates the S-VLAN tag ether type used for the packets
received on this port.Packets received on a port are considered tagged,
when the packet ethertype matches with the port ether type configured.
Otherw…
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.3
fsPbPortSVlanEgressEtherType
This object indicates the ether type of the S-VLAN tag that has to
be applied for all the outgoing packets on this port. If a valid value is
in this object, all the packets which are outgoing on this port will
contain t…
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.4
fsPbPortSVlanEtherTypeSwapStatus
This object indicates whether the Ether Type Swapping can be
applied on the S-VLAN tagged packets over this port.
The Ether type swapping will only be applied on S-VLAN tag of a packet.
This configuration is applicable …
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.5
fsPbPortSVlanTranslationStatus
This object indicates whether the VID Translation table can be
enabled on the incoming/outgoing packets on a particular port.
The Service Vlan swapping is applicable only for the externally
accesible network ports (ie…
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.6
fsPbPortUnicastMacLearning deprecated
A Truth value indicating the unicast MAC learning enabled/disabled
status for this port. When Unicast Mac Learning is disabled, No
Entry will be learned from the point of configuration on this port.
When Mac Learning is…
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.7
fsPbPortUnicastMacLimit
The Limiting value on the number of distinct unicast destination MAC
addresses that can be dynamically learnt over this interface.
The lower limit and upper limit value that can be SET for this object
is determined by t…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.8
fsPbPortBundleStatus
A Truth value indicating that Bundling enabled/disabled on port,
this Object can be enabled/disabled only for CEP. For other ports
setting and getting is not meaningful.
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.9
fsPbPortMultiplexStatus
A Truth value indicating that Bundling enabled/disabled on port, this Object can be enabled/disabled only for CEP. For other ports
setting and getting is not …
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.1.1.10

fsPbSrcMacSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.2 · 1 row entry · 3 columns
Open in standard view 
A table containing per port, per SourceMAC based Service VLAN
classification information in the device. Entries can be configured
into this table only when the bridge is configured as a
Provider Bridge and the Port Type for this port is SET
as  Proprietary Customer Edge Port / Proprietary Customer Network Port.
fsPbSrcMacSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.2.1
Information controlling Service VLAN classification at this
specified port for an ingress frame with the specified Source
MAC address in the ethernet header of the frame.
Indexes
fsPbPort fsPbSrcMacAddress
Column Syntax OID
fsPbSrcMacAddress
The Source MAC address present in the ethernet header of the
frame received on this port for which Service VLAN is assigned
based on this entry.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.113.2.2.1.1
fsPbSrcMacSVlan
The Service VLAN ID assigned to frames received on this port when
the Source MAC address in the ethernet header of the frame is same
as specified in this entry.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.2.1.2
fsPbSrcMacRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.2.1.3

fsPbDstMacSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.3 · 1 row entry · 3 columns
Open in standard view 
A table containing per port, per Destination MAC based Service
VLAN classification information in the device. Entries can be 
configured into this table only when the bridge is configured 
as a Provider Bridge. An entry in this table is possible only when the
'Port Type' for this port is SET as Proprietary Customer Network Port
or Proprietary Customer Edge Port.
fsPbDstMacSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.3.1
Information controlling Service VLAN classification at this
specified port for an ingress frame with the
specified Destination MAC address in the ethernet header of the frame.
Indexes
fsPbPort fsPbDstMacAddress
Column Syntax OID
fsPbDstMacAddress
The Destination MAC address present in the ethernet header of the
frame received on this port for which Service VLAN is assigned
based on this entry.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.113.2.3.1.1
fsPbDstMacSVlan
The Service VLAN ID assigned to frames received on this port when
the Destination MAC address in the ethernet header of the frame is
same as specified in this entry.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.3.1.2
fsPbDstMacRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.3.1.3

fsPbCVlanSrcMacSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.4 · 1 row entry · 4 columns
Open in standard view 
A table containing per Port, per Customer VLAN ID,
per Source MAC based S-VLAN classification information in the device.
Entries can be configured into this table only when the  bridge is
configured as a Provider Bridge. An entry in this table is
possible only when the 'PortType' for this port is SET as 
Proprietary Customer Edge Port / Proprietary Customer Network Port.
fsPbCVlanSrcMacSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.4.1
Information controlling Service VLAN classification at this specified
port for an ingress frame with the classified Customer VLAN ID and
with the specified Source MAC address in the ethernet header of the frame.
…
Indexes
fsPbPort fsPbCVlanSrcMacCVlan fsPbCVlanSrcMacAddr
Column Syntax OID
fsPbCVlanSrcMacCVlan
The Customer VLAN ID in the Customer VLAN tag of an ingress frame
at this specified port OR the Customer VLAN ID for which the ingress
frame is classified to this specified port.
Q-BRIDGE-MIBVlanId
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.4.1.1
fsPbCVlanSrcMacAddr
The Source MAC address in the ethernet header of the
frame received on this port.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.113.2.4.1.2
fsPbCVlanSrcMacSVlan
The Service VLAN assigned to frames received on this port,
When the Classified Customer VLAN ID is same as specified in
this entry and When the Source MAC address in the ethernet header
of the frame is same as specifi…
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.4.1.3
fsPbCVlanSrcMacRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.4.1.4

fsPbCVlanDstMacSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.5 · 1 row entry · 4 columns
Open in standard view 
A table containing per Port, per Customer VLAN ID,
per Destination MAC based S-VLAN classification information in the
device. Entries can be configured into this table only when the 
bridge is configured as a Provider Bridge. An entry in this table
is possible only when the 'Port Type' for this port is SET
as Proprietary Customer Edge Port / Proprietary Customer Network Port.
fsPbCVlanDstMacSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.5.1
Information controlling Service VLAN classification at this specified
port for an ingress frame with the classified Customer VLAN ID and
with the specified Destination MAC address in the ethernet header of
the frame.
…
Indexes
fsPbPort fsPbCVlanDstMacCVlan fsPbCVlanDstMacAddr
Column Syntax OID
fsPbCVlanDstMacCVlan
The Customer VLAN ID in the Customer VLAN tag of an ingress frame
at this specified port or the Customer VLAN ID for which the ingress
frame is classified for at this specified port.
Q-BRIDGE-MIBVlanId
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.5.1.1
fsPbCVlanDstMacAddr
The Destination MAC address in the ethernet header of the
frame received on this port.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.113.2.5.1.2
fsPbCVlanDstMacSVlan
The Service VLAN assigned to frames received on this port
when the Classified Customer VLAN ID and when the Destination
MAC address in the ethernet header of the frame is same as
specified in this entry.
…
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.5.1.3
fsPbCVlanDstMacRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.5.1.4

fsPbDscpSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.6 · 1 row entry · 3 columns
Open in standard view 
A table containing per port, per DiffServ Code Point (DSCP) value
based Service VLAN classification information in the device.
Entries can be configured into this table only when the bridge is 
configured as a Provider Bridge and the 'PortType' for
this port is SET as Proprietary Customer Network Port or 
Proprietary Customer Edge Port.
fsPbDscpSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.6.1
Information controlling Service VLAN classification at this
specified port for an ingress IP frame with the DSCP value as
specified in this entry.
Indexes
fsPbPort fsPbDscp
Column Syntax OID
fsPbDscp
The DSCP value in the IP header of the frame received on
this port for which Service VLAN is assigned based on this entry.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.10876.101.1.113.2.6.1.1
fsPbDscpSVlan
The Service VLAN ID assigned to IP frames received on this port
when the DSCP value in the IP header of the frame is same as
specified in this entry.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.6.1.2
fsPbDscpRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.6.1.3

fsPbCVlanDscpSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.7 · 1 row entry · 4 columns
Open in standard view 
A table containing per port, per Customer VLAN ID, per DiffServ Code
Point (DSCP) value based Service VLAN classification information in
the device. Entries can be configured into this table only when the
bridge is configured as a Provider Bridge and the 'PortType' for 
this port is SET as Proprietary Customer Edge Port / Proprietary Customer 
Network Port.
fsPbCVlanDscpSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.7.1
Information controlling Service VLAN classification at this
specified port for an ingress IP frame with the classified
Customer VLAN ID as specified in this entry and the DSCP value
in the frame as specified in this …
Indexes
fsPbPort fsPbCVlanDscpCVlan fsPbCVlanDscp
Column Syntax OID
fsPbCVlanDscpCVlan
The Customer VLAN ID in the Customer VLAN tag of an ingress frame
at this specified port or the Customer VLAN ID for which the ingress
frame is classified for at this specified port.
Q-BRIDGE-MIBVlanId
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.7.1.1
fsPbCVlanDscp
The DSCP value in the IP header of the frame received on
this port.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.10876.101.1.113.2.7.1.2
fsPbCVlanDscpSVlan
The Service VLAN ID assigned to frames received on this port,
when the classified Customer VLAN ID is the same as specified in
this entry and when the DSCP value in the IP header of the frame
is same as specified in th…
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.7.1.3
fsPbCVlanDscpRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.7.1.4

fsPbSrcIpAddrSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.8 · 1 row entry · 3 columns
Open in standard view 
A table containing per port, per Source IP Address, based Service VLAN
classification information in the device. Entries can be configured
into this table only when the bridge is configured as a Provider
Bridge and the 'PortType' for this port is SET as
Proprietary Customer Network Port or Proprietary Customer Edge Port.
fsPbSrcIpAddrSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.8.1
Information controlling Service VLAN classification at this
specified port for an ingress IP frame with the Source IP Address
in the IP header of the frame as specified in this entry.
Indexes
fsPbPort fsPbSrcIpAddr
Column Syntax OID
fsPbSrcIpAddr
The Source IP Address in the IP header of an ingress
IP frame at this specified port.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.113.2.8.1.1
fsPbSrcIpSVlan
The Service VLAN ID assigned to frames ingress at this port
when the Source IP address in the IP header of the frame is
same as specified in this entry.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.8.1.2
fsPbSrcIpRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.8.1.3

fsPbDstIpAddrSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.9 · 1 row entry · 3 columns
Open in standard view 
A table containing per port, per Destination IP Address, based
Service VLAN classification information in the device. Entries can
be configured into this table only when the bridge is configured as 
a Provider Bridge and the 'PortType' for this port is SET
as Proprietary Customer Network Port or Proprietary Customer Edge Port.
fsPbDstIpAddrSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.9.1
Information controlling Service VLAN classification at this
specified port for an ingress IP frame with the Destination IP
Address in the IP header of the frame as specified in this entry.
Indexes
fsPbPort fsPbDstIpAddr
Column Syntax OID
fsPbDstIpAddr
The Destination IP Address in the IP header of an ingress
IP frame at this specified port.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.113.2.9.1.1
fsPbDstIpSVlan
The Service VLAN ID assigned to frames ingress at this port
when the Destination IP address in the IP header of the frame is
same as specified in this entry.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.9.1.2
fsPbDstIpRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.9.1.3

fsPbSrcDstIpSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.10 · 1 row entry · 4 columns
Open in standard view 
A table containing per port, per Source IP Address, per Destination
IP Address based Service VLAN  classification information in the
device. Entries can be configured into this table only when the bridge
is configured as a Provider Bridge and the'PortType' for
this port is SET as Proprietary Customer Network Port or Proprietary 
Customer Edge Port.
fsPbSrcDstIpSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.10.1
Information controlling Service VLAN classification at this
specified port for an ingress IP frame with the Source and Destination
IP Address in the IP header of the frame as specified in this entry.
Indexes
fsPbPort fsPbSrcDstSrcIpAddr fsPbSrcDstDstIpAddr
Column Syntax OID
fsPbSrcDstSrcIpAddr
The Source IP Address in the IP header of an ingress
IP frame at this specified port.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.113.2.10.1.1
fsPbSrcDstDstIpAddr
The Destination IP Address in the IP header of an ingress
IP frame at this specified port.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.113.2.10.1.2
fsPbSrcDstIpSVlan
The Service VLAN ID assigned to frames ingress at this port
when the Source and Destination IP address in the IP header of
the frame are same as specified in this entry.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.10.1.3
fsPbSrcDstIpRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.10.1.4

fsPbCVlanDstIpSVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.11 · 1 row entry · 4 columns
Open in standard view 
A table containing per port, per Customer VLAN ID, per Destination
IP Address, based Service VLAN classification information in the 
device. Entries can be configured into this table only when the bridge
is configured as Provider Bridge or Provider Edge Bridge and the 
Port Type for this port is SET as Proprietary Customer Edge Port 
/ Proprietary Customer Network Port.
fsPbCVlanDstIpSVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.11.1
Information controlling Service VLAN classification at this specified
port for an ingress IP frame with the classified Customer VLAN ID as
specified in this entry and the Destination IP Address in the IP header
of the…
Indexes
fsPbPort fsPbCVlanDstIpCVlan fsPbCVlanDstIp
Column Syntax OID
fsPbCVlanDstIpCVlan
The Customer VLAN ID in the Customer VLAN tag of an ingress frame
at this specified port or the Customer VLAN ID for which the ingress
frame is classified for at this specified port.
Q-BRIDGE-MIBVlanId
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.11.1.1
fsPbCVlanDstIp
The Destination IP Address in the IP header of an ingress
IP frame at this specified port.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.113.2.11.1.2
fsPbCVlanDstIpSVlan
The Service VLAN ID assigned to frames ingress at this port
when the classified Customer VLAN ID is same as specified in this entry
and the Destination IP address in the IP header of the frame is same
as specified in …
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.11.1.3
fsPbCVlanDstIpRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.11.1.4

fsPbPortBasedCVlanTable

table
.1.3.6.1.4.1.10876.101.1.113.2.12 · 1 row entry · 2 columns
Open in standard view 
A table containing Customer Edge Port / Proprietary Customer Edge Port / 
Proprietary Customer Network Port mapping to Customer VLAN on a
providerBridge. This table is used for a classifying a untagged frame 
received on above mentioned customer ports.
fsPbPortBasedCVlanEntry entry .1.3.6.1.4.1.10876.101.1.113.2.12.1
An Entry in this table will be created whenever a port is configured as
Customer Edge Port / Proprietary Customer Edge Port / Proprietary Customer
Network Port.This Entry will be used on the ingress frame on the specifi…
Indexes
fsPbPort
Column Syntax OID
fsPbPortCVlan
The Customer VLAN ID assigned to untagged frames ingress at this
specified Customer Edge Port / Proprietary Customer Edge Port /
Proprietary Customer Network Port.
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.10876.101.1.113.2.12.1.1
fsPbPortCVlanClassifyStatus
This object indicate C-VLAN classification status on a port.
This Object can be enabled/disabled only for PropCEP/PropCNP. For CEP,
this object cannot be disabled.
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.12.1.2

fsPbEtherTypeSwapTable

table
.1.3.6.1.4.1.10876.101.1.113.2.13 · 1 row entry · 3 columns
Open in standard view 
A Table containing the Translation information of  the ethertype for a 
Service VLAN in a given packet. This Table shall be used only at ingress 
and NOT at egress of the Customer Network Port / Proprietary Customer Network 
Port / Provider Network Port. 
This translation table is applicable for only Service VLAN and not 
for customer VLAN's.
fsPbEtherTypeSwapEntry entry .1.3.6.1.4.1.10876.101.1.113.2.13.1
Entry containing the Local and Relay Ether type for a given packet on
a particular port. This entry shall be applicable on all types of ports
if and only if fsPbPortSVlanEtherTypeSwapStatus is Enabled on that Port.
Indexes
fsPbPort fsPbLocalEtherType
Column Syntax OID
fsPbLocalEtherType
The Ether type present in the service vlan tag of the ingress packet at
the given port.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.113.2.13.1.1
fsPbRelayEtherType
The Relay Ether type mapped for the ether type present in the local
service vlan tag of the ingress packet at the given port.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.113.2.13.1.2
fsPbEtherTypeSwapRowStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.113.2.13.1.3

fsPbSVlanConfigTable

table
.1.3.6.1.4.1.10876.101.1.113.2.14 · 1 row entry · 1 columns
Open in standard view 
The table to configure the service type supported by an S-VLAN. Based 
on the service type configured for the S-VLAN, the oper point-to-point  
state of PEP ports will be determined.
fsPbSVlanConfigEntry entry .1.3.6.1.4.1.10876.101.1.113.2.14.1
The service type can be configured for an S-VLAN only when the VLAN
is already created in the system.
Indexes
Q-BRIDGE-MIBdot1qVlanIndex
Column Syntax OID
fsPbSVlanConfigServiceType
The object to specify the service type supported by the S-VLAN. When
it is set to 'eLine', the S-VLAN connects not more than two customer
interfaces. If the service type for a vlan is 'eLine', then learning
member po…
Enumerationr/w
Enumerated Values:
1eLine
2eLan
 .1.3.6.1.4.1.10876.101.1.113.2.14.1.1

fsPbTunnelProtocolTable

table deprecated
.1.3.6.1.4.1.10876.101.1.113.2.15 · 1 row entry · 6 columns
Open in standard view 
This table contains information about the handling (Tunnel/Peer/
Discard)of customer Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x
and IGMP) inside service provider network.
This table is supported only for Provider Core or Provider Edge 
Bridges.
fsPbTunnelProtocolEntry entry .1.3.6.1.4.1.10876.101.1.113.2.15.1
Entry indicating the handling (Tunnel/Peer/Discard) of Layer 2
protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) on this port.
Indexes
fsPbPort
Column Syntax OID
fsPbTunnelProtocolDot1x deprecated
The object to specify whether to peer/tunnel/discard the Dot1x packets
received on this port.
TunnelStatusr/w
Textual Convention: TunnelStatus Enumeration
Type Values:
1peer
2tunnel
3discard
 .1.3.6.1.4.1.10876.101.1.113.2.15.1.1
fsPbTunnelProtocolLacp deprecated
The object to specify whether to peer/tunnel/discard the LACP packets
received on this port.
TunnelStatusr/w
Textual Convention: TunnelStatus Enumeration
Type Values:
1peer
2tunnel
3discard
 .1.3.6.1.4.1.10876.101.1.113.2.15.1.2
fsPbTunnelProtocolStp deprecated
The object to specify whether to peer/tunnel/discard the STP packets
received on this port.
TunnelStatusr/w
Textual Convention: TunnelStatus Enumeration
Type Values:
1peer
2tunnel
3discard
 .1.3.6.1.4.1.10876.101.1.113.2.15.1.3
fsPbTunnelProtocolGvrp deprecated
The object to specify whether to peer/tunnel/discard the GVRP packets
received on this port.
TunnelStatusr/w
Textual Convention: TunnelStatus Enumeration
Type Values:
1peer
2tunnel
3discard
 .1.3.6.1.4.1.10876.101.1.113.2.15.1.4
fsPbTunnelProtocolGmrp deprecated
The object to specify whether to peer/tunnel/discard the GMRP packets
received on this port.
TunnelStatusr/w
Textual Convention: TunnelStatus Enumeration
Type Values:
1peer
2tunnel
3discard
 .1.3.6.1.4.1.10876.101.1.113.2.15.1.5
fsPbTunnelProtocolIgmp deprecated
The object to specify whether to peer/tunnel/discard the IGMP packets
received on this port.
TunnelStatusr/w
Textual Convention: TunnelStatus Enumeration
Type Values:
1peer
2tunnel
3discard
 .1.3.6.1.4.1.10876.101.1.113.2.15.1.6

fsPbTunnelProtocolStatsTable

table deprecated
.1.3.6.1.4.1.10876.101.1.113.2.16 · 1 row entry · 12 columns
Open in standard view 
This table contains statistics information about the tunneled 
Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) received 
and transmitted over a port.
fsPbTunnelProtocolStatsEntry entry .1.3.6.1.4.1.10876.101.1.113.2.16.1
Entry indicating the handling (Tunnel/Peer/Discard) of Layer 2
protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) on this port.

This table is supported only for Provider Core or Provider Edge
Bridges.
Indexes
fsPbPort
Column Syntax OID
fsPbTunnelProtocolDot1xPktsRecvd deprecated
The number of tunneled Dot1x Packets received.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.1
fsPbTunnelProtocolDot1xPktsSent deprecated
The number of tunneled Dot1x Packets transmitted.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.2
fsPbTunnelProtocolLacpPktsRecvd deprecated
The number of tunneled LACP Packets received.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.3
fsPbTunnelProtocolLacpPktsSent deprecated
The number of tunneled LACP packets transmitted.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.4
fsPbTunnelProtocolStpPDUsRecvd deprecated
The number of tunneled STP PDUs received.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.5
fsPbTunnelProtocolStpPDUsSent deprecated
The number of tunneled STP PDUs transmitted.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.6
fsPbTunnelProtocolGvrpPDUsRecvd deprecated
The number of tunneled GVRP PDUs received.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.7
fsPbTunnelProtocolGvrpPDUsSent deprecated
The number of tunneled GVRP PDUs transmitted.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.8
fsPbTunnelProtocolGmrpPktsRecvd deprecated
The number of tunneled GMRP PDUs packets received.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.9
fsPbTunnelProtocolGmrpPktsSent deprecated
The number of tunneled GMRP packets transmitted.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.10
fsPbTunnelProtocolIgmpPktsRecvd deprecated
The number of tunneled IGMP packets received.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.11
fsPbTunnelProtocolIgmpPktsSent deprecated
The number of tunneled IGMP packets transmitted.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.113.2.16.1.12

fsPbPepExtTable

table
.1.3.6.1.4.1.10876.101.1.113.2.17 · 1 row entry · 1 columns
Open in standard view 
This is an extention of dot1adPepTable table, and it provides       
additional configurations to PEPs (like Cos Preservations,..). 
when a entry in dot1adPepTable is created, then an entry will be
created in this table.
fsPbPepExtEntry entry .1.3.6.1.4.1.10876.101.1.113.2.17.1
Entry contains information like (COS preservation, ..) for the
internal PEPs. Creation of an entry in this table is not allowed
and only modification is allowed.
Indexes
No indexes recorded
Column Syntax OID
fsPbPepExtCosPreservation
This object is used to enable or disable COS preservation for a
service provided by this PEP.
P-BRIDGE-MIBEnabledStatusr/w
Textual Convention: P-BRIDGE-MIBEnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.113.2.17.1.1