RAD-Ipmux-MIB Table View

The channel index, which is actualy the bundle ID.

This parameter allows NMS to create/delete entries of this table.

The actual link status.
remoteFail - No Rx.
localFail - No Tx.
unavailable - No echo replay or replay with invalid code or when connection is in Test state.
valiodationFail - Connection is in not valid state.
standby -…

The desired state of the link.

The destination IP address.

The next hop to which the frame should be sent.
Default value - 0.0.0.0.
Upon setting the default value the frame is sent
to the default Gateway.

The destination Bundle at the far-end device.

The Destination MAC address of the next hop or
destination station.

The maximum cell arrival jitter in 10 usec that the
reassembly process will tolerate in the cell stream,
without producing errors on the CBR service interface.

For KM2100:
KML.11 - The range that w…

The TOS (Type of Service) value: 0..255.

In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0:
LSB 8 bits - 00 00 00 XX will be used for Signaling packets TOS.
N…

The number of TDM bytes to be placed in a single IP
frame payload.
For ip2IfTDMoIpMode = cesOverPsn this parameter indicates
the number of IP frames, calculated as: 1440/<Number of Timeslots>.

VLAN support (Tagging).
no - No support to VLAN.
yes - 4 VLAN bytes will be added to the frame.

VLAN ID.

VLAN Frame priority.

This object determines to which external port the traffic
will be sent.
auto - the device will decide automatically the exit port.
If there is an option for Tx via more than one ETH card then use ext1 (1) and ext2(2)
f…

Voice Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

Data Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

The Bundle Resource usage in Kbps.

This parameter determine the OAM configuration.
The LSB (Bit 0 the most right one) is used for OAM connectivity.
Values: 0 = disable, 1= enable.

The TDMoIP Mode configuration. Static- means TS can Tx any time.
dynamicLES - means TS can Tx only when line is enabled according to LES protocol.
dynamicCAS - means TS can Tx only when line is enabled according to CAS …

The number of seconds that have elapsed since
the beginning of the current error-measurement period.
If, for some reason, such as an adjustment in the
system's time-of-day clock, the current interval exceeds
the maxim…

The number of previous intervals for which data was collected.
The value will be 96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute in…

This object defines the type of the Far-End device.
This data is important for signaling and DS0 format.

For Vmux: e1 (2) value is used for a PBX in the Far End.
fxs (5) is used for Phone.
…

This object defines the role this bundle plays in the redundancy scheme:
none(2) - means this bundle is not part of redundancy pair.
primary/ secondary - means this bundle is not part of redundancy pair,
and that is the…

Source IP Address of the bundle.

Defines the Bandwidth of the bundle.

For TDM bundles - it is the Number of Time Slots in The Bundle.
- For T1 the value will be: 1..24
- For E1 the value will be: 1..31
- For T3 the value will be: 1..84
…

This object shows the percentage of Silence that was measured by the device
for the current bundle in the transmitted payload.
Relevant values: 0..100, 255.
Default value is 50.
0 means that there is no silence on the l…

This object defines the TDMoIP payload type.

This object defines the TDMoIP protocol Version.

Defines the TDM bundle default router in case there was a switch from the Primary Link
(for example an ETH port) to a TDM backup Link like E1, T1 or Serial Link.
This parameter is relevant only when a Backup Link is con…

This object defines whether OOS will be Transmitted.
Note that for IPmux1000 the Lbit is always sent,
but the OOS will be sent according to user selection in this parameter.

Time in sec. between 2 Bundle Connectivity Check packets.
Valid values: 0..60. 0 = Not Applicable.

No. of cycles the agent will send Bundle Connectivity packets without receiving
a response from the remote device before declaring that the bundle connection
to the remote side is down - Time Out.
Valid values: 0..5. 0 …

Multi Frequency Signaling Detection.

Transmit gain in dBm.

The Super Tandem feature provides end to end compression over multiple hops,
solving the double compression problem detected in Voice compressing systems.
The Super Tandem allows transmission of compressed voice between…

The source Bundle at the local device,
this parameter used for cases where there is no match
between ip2IfChannelIndex and the Source Bundle ID.

This MIB object shows whether Modem Calls are enabled via the bundle.
relay option (3) means that the bundle will send to the network only
modulated data.

Indicates the minimum width in milliseconds of the MF (Multi Frequency)
tone transmitted by the switch.
Valid values: 45-300 msec.
notApplicable=0.

Indicates the minimum power level in dBm of the MF (Multi Frequency)
tone transmitted by the switch.
Valid values: -1...-35 dBm.

Echo canceler activation.

This attribute indicates the Method/Law for decoding/encoding the voice
information.
aLaw(1) is the standard Law for E1 links.
uLaw(2) is the standard Law for T1 links.

Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector.
This tone is sent between PBX devices in order to check that the line status
is OK. When the COT is enabled the device will not compress/decomp…

Time in msec between CLID (Caller ID) signal detection on the line and CLID
signal transmission. The CLID must be sent between ringing signals and the value
of the delay is used for synchronizing the CLID transmission w…

This MIB object shows whether to send Pings or OAM frames over the bundle.

This MIB object defines whether this bundle can be a clock source.

This MIB object defines the network over which the
Bundle PSN (Packet Switching Network)is transported.
In Gmux2000:
ipComprHeader indicates proprietary compressed IP header packets.
mplsComprHeader indicates proprieta…

This MIB object defines whether there is user defined
inner (Rx.) label for this Bundle.

This MIB object defines the MPLS Rx. Label for this Bundle.

This MIB object defines whether there is user defined
outer (Tx.) label for this Bundle.

This MIB object defines the MPLS Tx. Label for this Bundle.

The MPLS Network priority (EXP bits) used for this bundle.

This MIB object defines whether the MFC (Multi Frequency Compelled) protocol
spoofing will exist in the bundle. When the MFC Spoofing is used, the Local
and Remote PBXs will send MFC Signaling to each other. The Vmuxes …

Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until
it receives an acknowledgement from this PBX.
Valid values: 60...400 in steps of 20.

This MIB object defines the Bundle next Hop Address Type.

This object defines the Level of Noise on the line,
the Voice Activation Detector (VAD) will have to handle.

The Clock preferences:
accurateness (2) = Accurate clock is more important than Constant Delay.
constantDelay (3)= Constant Delay is more important than Accurate clock .

The Connection Mode:
tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation.
tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice.

Enables or disable Ring Back.

Enables or disable Reverse polarity synthesis.

Enables or disable Pulse metering synthesis.

Frequency of synthesized pulse metering for this bundle.

Duration of synthesized pulse metering. current values are: 100-250.

Enables or disable immediate reaction to On-Hook bits from network in Ringing.

Enable or disable Comfort Noise Generation (CNG).
When this parameter is enabled and no voice payload exists on the line for some
time period during the call (moments of silence), the device will generate a soft
back…

The channelized bundle that the voice bundle exits through.
In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel)
that the Voice Bundle exits through. The ifIndex contains
the Slot+Prt+Channelized Bund…

Maximum VBD modem calls for this bundle.

Maximum Relay modem calls for this bundle.

This is the frequency of the Custom Tone that is sent between PBXs in order
to check that the line status is OK. When the Custom Tone Detection is enabled
the device will not compress/decompress this tone. The custom to…

Voice Activity Detection (VAD) method.
proprietary (2) - non standard VAD based only on power measurement.
It is very sensitive to background noise.
internalITUT (3) - standard ITU-T VAD. It is …

Receive gain in dBm.

Caller ID Type used by the DSP for this bundle.
Bellcore type is used by the American method.
V.23 type is used by the European method.

This MIB object defines the peer Address Type.

Voice Band Data (VBD) rate for this bundle.

Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle.

Non Linear Processor (NLP) Cutoff Level for this bundle.
This parameter is used by the echo canceller.
It is the maximum absolute linear PCM amplitude of the near-end signal that will
cause the NLP module to be active a…

The DTD ERL cutoff level is used in order to determine whether the near-end is talking
or not. This parameter is used by the echo canceller when echo exists and there is
voice with low volume on the line.
DTD means Doub…

Enable/Disable CAS signaling redundancy.
This parameter is useful when there are problems with the network and applicable
only for CAS signaling: E1-MF (G.732S) or E1-CRC-MF (G.732SCRC ).

enable (3) - mea…

Denotes if the bundle is sensitive to delay in the network,
or is sensitive to data errors in the network.
Voice bundles are sensitive to delay;
Non-voice bundles are sensitive to data errors.

Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff),
or according to the value of the first nibble in the VCCV control word sent in the frame.
controlWord - applicable only when ip2IfProtoco…

Max Tx Queue buffer size, measured in msec (milliseconds).

Low buffer size may cause the buffer to overflow and discard packets
in case of burst of packets on the network.

High buffer size …

Max GPRS Tx Queue buffer size, measured in msec (milliseconds).

Low buffer size may cause the buffer to overflow and discard packets
in case of burst of packets on the network.

High …

This parameter shows whether V.23 Half Duplex Modem Protocol is enabled
on the bundle.

This octet string contains the mode of each Modem Protocol used on the bundle.
For each protocol one octet will be used.

Octet #1 will be used for V.22 Protocol.
Octet #2, #3, #4... are reserved for futu…

When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation):
The time in msec that the device will detect 1100Hz & 2100Hz signals
on the line before switching to modem or fax.
For Vmux: the val…

This MIB object enables controlling the Time Slot/Channel rate.
Valid values: 1 - FF HEX
Each BIT represents 1/8 of the TS.
Example:
7E (0111 1110) means that 6/8 of the TS (the center ones) are masked and data will
be …

Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice.
For Vmux: the values will be in steps of 30 msec.

The gain value in dBm units used for transmitting the Caller ID signal on the bundle.

The gain value in dBm units of the Caller ID signal received on the bundle.

This parameter determines according to which field the multiplexing is made:
srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e).
This should be the default value, for backwards compatibility.…

Enable/Disable Caller ID Detection for this bundle.

Enable/Disable WAP (Wireless Application Protocol) for this bundle.
WAP allows users to access the internet from wireless devices.

Out of Service code sent on signaling TimeSlot.

The channel index, which is actualy the bundle ID.

Number of events that the sequence number of an incoming Frame
causes a transition from the 'sync' state to
the 'out of sequence' state.

Number of events that the buffer underflows. This records the count of the
number of events the Receive (Eth to TDM) buffer underflows. In the
case of a continuous underflow caused by a loss of Frame
flow, a single buff…

Number of events that the buffer overflows. This records the count of the
number of events the Receive (Eth to TDM) buffer overflows.

Number of frames that were transmitted due to time interval elapse.
The user can choose to Tx the Frame when it reaches the Max size
or when the packetizing time interval elapses.
The packetizing time interval is the in…

Number of frames that were transmitted due to reaching max.
frame size. The user can choose to Tx the Frame when it reaches the
Max size or when the packetizing time interval elapses.

Number of signaling frames that were received.

Number of voice frames that were received.

Number of HDLC frames that were received.

Number of signaling frames that were transmitted.

Number of voice frames that were transmitted.

Number of HDLC frames that were transmitted.

Number of redundancy flips occured.
This parameter counts only flips from this bundle to the other bundle
in the redundancy couple.

This variable indicates the Status of the Far-End TDM Line.
It contains failure state information.
The variable is a bit map represented as a sum, therefore, it
can represent multiple failures simultaneously.
The …

Number of frames that were transmitted to PSN.

Number of frames that were recieved from PSN.

The Minimum jitter buffer level (in msec).

The Maximum jitter buffer level (in msec).

The Recommended jitter buffer Size (in msec).
0= not applicable.

Number of times that the sequence number of an incoming Frame
indicates Loss of Frame or Out of order occured in PSN.

Number of times that Frames had been reordered in PSN.

The minimum Round Trip delay (in msec).
0= not applicable.

The maximum Round Trip delay (in msec).
0= not applicable.

The avarage Round Trip delay (in msec).
0= not applicable.

The number of packets dropped due to being duplicated.
(duplicated packet means a packet that has the same sequential
number as a packet being received previously).

The number of packets that are missing.
(Missing packet means an expected packet- according to the current sequential
number - that was not received).

The longest series of consecutive missing sequential numbers.
Missing sequential numbers represent missing packets that was
expected to be received successively.

This object shows the percentage of Silence that was measured by the device
for the current bundle in the transmitted payload.
Relevant values: 0..100, 255.
Default value is 50.
0 means that there is no silence on the l…

This object shows the percentage of Silence that was measured by the device
for the current bundle in the received payload.
Relevant values: 0..100, 255.
Default value is 50.
0 means that there is no silence on the line…

This counter indicates the number of received HDLC frames
with CRC errors.

This counter indicates the number of received HDLC frames
with alignment errors.

This counter indicates the number of received HDLC frames
longer than 1470.

This counter indicates the number of received HDLC frames
shorter than 4.

This counter indicates the number of received HDLC frames
with abort indication.

Number of received correct frames.

Number of received errored HDLC frames.

The Port index, which is actualy the ifIndex.

This parameter indicates the usage of the port (percents).

This parameter defines whether Agent will mask port's alarms and statistics or not.

This parameter indicates the total Throughput of the port in bps.

Number of seconds that the sequence number of an incoming Frame
causes a transition from the 'sync' state to
the 'out of sequence' state in the current interval.

Number of seconds that the buffer underflows in the current interval.
This records the count of the number of seconds the Receive
(Eth to TDM) buffer underflows in the current interval. In the
case of a continuous und…

Number of seconds that the buffer overflows in the current interval.
This records the count of the number of seonds the Receive
(Eth to TDM) buffer overflows in the current interval.

The maximum deviation from the center of the buffer (in msec) for the current interval.

The Minimum jitter buffer level (in msec) for the current interval.

The Maximum jitter buffer level (in msec) for the current interval.

The number of seconds in which errored frames were transmitted during the current interval.
The error may be one of the following:
CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.

The Interval index, which is actualy the Interval number.

Number of seconds that the sequence number of an incoming Frame
causes a transition from the 'sync' state to
the 'out of sequence' state in the selected interval.

Number of seconds that the buffer underflows in the selected interval.
This records the count of the number of seconds the Receive
(Eth to TDM) buffer underflows in the selected interval. In the
case of a continuous u…

Number of seconds that the buffer overflows in the selected interval.
This records the count of the number of seconds the Receive
(Eth to TDM) buffer overflows in the selected interval.

The maximum size of the buffer (in 10's of usec) in the selected interval.
For some devices (e.g. MP-4100) units are usec.

The Minimum jitter buffer level (in msec) for the selected interval.
For some devices (e.g. MP-4100) units are usec.

The Maximum jitter buffer level (in msec) for the selected interval.
For some devices (e.g. MP-4100) units are usec.

The number of seconds in which errored frames were transmitted during the selected interval.
The error may be one of the following:
CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.