RAD-BrgGen-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
29
Rows
29
Columns
220
.1.3.6.1.4.1.164.4.1.3 · 1 row entry · 20 columns
Mask tables enable definition of forwarding restrictions and 
control of message flow in the internetwork. Each entry
in this table defines a mask statement consisting of up to 
three mask definitions and an action defined by 
radBridgeMaskOper. Different types of mask entries are supported, 
as defined by radBridgeMaskType.
radBridgeMaskEntry entry .1.3.6.1.4.1.164.4.1.3.1
An entry in table radBridgeMaskTable.
Indexes
No indexes recorded
Column Syntax OID
radBridgeMaskType
Defines the type of mask entry.
Enumeration .1.3.6.1.4.1.164.4.1.3.1.1
radBridgeMaskIfIndex
Specifies the if Index of the interface to which the mask is applied.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.3.1.2
radBridgeMaskNum
The Mask entry number, defined by its line number in the mask
table.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.3.1.3
radBridgeMaskDest
Specifies the type of destination address carried by the frame
to which the mask will be applied. Unassigned-condition
deactivates the mask entry.
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.4
radBridgeMaskPat1
Describes the mask field which is either a 16 bit binary pattern,
or four digit hexadecimal pattern.
OctetStringr/w .1.3.6.1.4.1.164.4.1.3.1.5
radBridgeMaskActiveBit1
Specifies the positions of the wild card characters (*)
in the radBridgeMaskPat1 field.
OctetStringr/w .1.3.6.1.4.1.164.4.1.3.1.6
radBridgeMaskFrom1
Offset base of radBridgeMaskPat1 within the frame.
Net can be in some cases the data start point.
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.7
radBridgeMaskOffset1
Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from
the base defined in by radBridgeMaskForm1.The mask offset is an even
decimal number in the range of 0 to 1518.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.3.1.8
radBridgeMaskCond1
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
radBridgeMaskOffset1 the packet contains data that matches
the content of radBridgeMaskPa…
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.9
radBridgeMaskPat2
Describes the mask field which is either a 16 bit binary pattern,
or four digit hexadecimal pattern.
OctetStringr/w .1.3.6.1.4.1.164.4.1.3.1.10
radBridgeMaskActiveBit2
Specifies the positions of the wild card characters (*)
in the radBridgeMaskPat2 field.
OctetStringr/w .1.3.6.1.4.1.164.4.1.3.1.11
radBridgeMaskFrom2
Offset base of radBridgeMaskPat2 within the frame.
Net can be in some cases the data start point.
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.12
radBridgeMaskOffset2
Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from
the base defined in by radBridgeMaskForm2.The mask offset is an even
decimal number in the range of 0 to 1518.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.3.1.13
radBridgeMaskCond2
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
radBridgeMaskOffset2 the packet contains data that matches
the content of radBridgeMaskPa…
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.14
radBridgeMaskPat3
Describes the mask field which is either a 16 bit binary pattern,
or four digit hexadecimal pattern.
OctetStringr/w .1.3.6.1.4.1.164.4.1.3.1.15
radBridgeMaskActiveBit3
Specifies the positions of the wild card characters (*)
in the radBridgeMaskPat3 field.
OctetStringr/w .1.3.6.1.4.1.164.4.1.3.1.16
radBridgeMaskFrom3
Offset base of radBridgeMaskPat3 within the frame.
Net can be in some cases the data start point.
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.17
radBridgeMaskOffset3
Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from
the base defined in by radBridgeMaskForm3. The mask offset is an even
decimal number in the range of 0 to 1518.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.3.1.18
radBridgeMaskCond3
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
radBridgeMaskOffset3 the packet contains data that matches
the content of radBridgeMaskPa…
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.19
radBridgeMaskOper
The type of action to be taken if the frame meets the
conditions of the mask.
noOp = disabled (mask remains on list, but is not active)
delete = mask is removed from the list.
Enumerationr/w .1.3.6.1.4.1.164.4.1.3.1.20
.1.3.6.1.4.1.164.4.1.4.1 · 1 row entry · 8 columns
The table of COD parameters
radBridgeCODEntry entry .1.3.6.1.4.1.164.4.1.4.1.1
Each radBridgeCODEntry consists of the following parameters
Indexes
No indexes recorded
Column Syntax OID
radBridgeCODIfIndex
The interface to which this COD entry is applicable.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.1.1.1
radBridgeCODManualConnect
The management station can start connection manually
by setting this parameter
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.1.1.2
radBridgeCODMode
In answer mode only one incoming call may be accepted at a time. Other nodes
attempting to access the local modem will receive a busy signal until the
connection is terminated. (Answer mode has no difficulty supporting …
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.1.1.3
radBridgeCODConnectDelay
The connect delay defines the minimum time period that
the link must stay disconnected, between 2 succesive
connections (in seconds).
SNMPv2-SMIInteger32r/w
Constraints:
range: 1-255
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.1.1.4
radBridgeCODisConnectDelay
The disconnect delay defines the minimum time period
the link must stay connected, between 2 succesive
disconnections (in seconds).
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.1.1.5
radBridgeCODImplicitSwitch
The inplicit switch allows the user to ignore implicit triggers provided
by the COD software.
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.1.1.6
radBridgeCODNumAccess
The number of successful connections that have been established since
the COD has been reset.
SNMPv2-SMICounter32
Constraints:
range: 10-1000000
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.4.1.1.7
radBridgeCODTotalConnecTime
The sum of all the connect time intervals since the COD was reset.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.1.1.8
.1.3.6.1.4.1.164.4.1.4.2 · 1 row entry · 6 columns
The table of COD parameters
radBridgeCODTimeTriggerEntry entry .1.3.6.1.4.1.164.4.1.4.2.1
Each radBridgeCODTimeTriggerEntry consists of the following parameters
Indexes
No indexes recorded
Column Syntax OID
radBridgeCODTimeIfIndex
The interface to which this COD Time Trigger entry is applicable.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.2.1.1
radBridgeCODDay
The day of the week in which the dial up connection operates.
Enumeration .1.3.6.1.4.1.164.4.1.4.2.1.2
radBridgeCODTimeTriggerNum
Every day of the week the user can configure 3 dial up connections.
Integer32 .1.3.6.1.4.1.164.4.1.4.2.1.3
radBridgeCODTimeTriggerFrom
Time to start Dial Up connection, in format hh:mm.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.4.1.4.2.1.4
radBridgeCODTimeTriggerTo
Time to terminate Dial Up connection, in format HH:MM.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.4.1.4.2.1.5
radBridgeCODTimeTriggerStatus
The status of a table entry.
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.2.1.6
.1.3.6.1.4.1.164.4.1.4.3.1 · 1 row entry · 2 columns
The table of COD Traffic trigger
radBridgeCODTrafficEntry entry .1.3.6.1.4.1.164.4.1.4.3.1.1
Each radBridgeCODTrafficEntry consists of the following parameters.
Indexes
No indexes recorded
Column Syntax OID
radBridgeCODProtocolType
The Protocol Type of the Traffic Table
Enumeration .1.3.6.1.4.1.164.4.1.4.3.1.1.1
radBridgeCODTrafficTriggerStatus
Command of Status of the Protocol Traffic Trigger
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.3.1.1.2
.1.3.6.1.4.1.164.4.1.4.4 · 1 row entry · 7 columns
The table of COD Condition parameters
radBridgeCODCondEntry entry .1.3.6.1.4.1.164.4.1.4.4.1
Each radBridgeCODCondEntry consists of the following parameters
Indexes
No indexes recorded
Column Syntax OID
radBridgeCODCondIfIndex
The interface, this COD entry is applicable to.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.4.1.1
radBridgeCODOriginateConnectCondition
This condition, allows the user to specify the
condition under which the link is connected.
The options are
onPowerOn - On power on.
whenAnyStationOnLan - When any station on lan.
onTraffic - …
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.4.1.2
radBridgeCODOriginateDisConnectCondition
This condition allows the user to specify the
condition under which the link is disconnected.
The options are:
noStationOnLan - When there is no station on lan.
Counts 15 minutes from the point …
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.4.1.3
radBridgeCODOriginateDisConnectDelay
Delay time in seconds.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.4.1.4
radBridgeCODAnswerConnectCondition
CODCondAnswerConnect allows the user to specify
the condition under which the link is connected.
The options are:
onPowerOn - On power on.
whenAnyStationOnLan - When any station on lan.
onTraffic …
Enumerationr/w .1.3.6.1.4.1.164.4.1.4.4.1.5
radBridgeCODSpecificOnTrafficOIDCondition
A reference to a specific entry in the
radBridgeMaskTable, which describes the
particular COD condition .
If Connect or Disconnect Conditions are not
onTraffic, its value should be set to the
OBJECT IDENTIFIER { 0 0 …
ObjectIdentifier .1.3.6.1.4.1.164.4.1.4.4.1.6
radBridgeCODDisConnectMinimunFramesNumber
Frames rate.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.4.4.1.7
.1.3.6.1.4.1.164.4.1.5.2.6 · 1 row entry · 9 columns
The routing table used by RIP to calculate routes to remote
desination networks.
radBridgeIPXRipTableEntry entry .1.3.6.1.4.1.164.4.1.5.2.6.1
The routing information for one of this entity's destination networks.
Indexes
bridgeMacSearchIdx
Column Syntax OID
radBridgeIPXRipDestNetwork
The destination network address to which this entry's
routing information pertains.
OctetString .1.3.6.1.4.1.164.4.1.5.2.6.1.1
radBridgeIPXRipPolicy
A value specifying the precidence of the route. A value of
zero means that the route is the best route, a value of one
means that the route is the second best route and so on.
Enumeration .1.3.6.1.4.1.164.4.1.5.2.6.1.2
radBridgeIPXRipForwardingRouter
The IPX node address of the next hop (router) for the
entry's associated destination network.
OctetStringr/w .1.3.6.1.4.1.164.4.1.5.2.6.1.3
radBridgeIPXRipNIC
An interface identifier specifying what IPX interface the
next hop can be found on.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.2.6.1.4
radBridgeIPXRipTickMetric
The metric, in terms of transit time, associated with the route
given by the entry. This time is in terms of 1/18ths of a
second.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.2.6.1.5
radBridgeIPXRipHopMetric
The metric, in terms of distance , associated with the route
given by the entry.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.2.6.1.6
radBridgeIPXRipAgingTime
The last time that the entry was updated. The time will be
provided in terms of the MIB-I object sysUpTime.
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.5.2.6.1.7
radBridgeIPXRipValueStatus
The entry status value; whether the entry is permanent (added
statically), reachable or unreachable. In the latter two cases
it would be added by RIP. A semiDynamic entry is an entry
enterd manualy by the user and can …
Enumerationr/w .1.3.6.1.4.1.164.4.1.5.2.6.1.8
radBridgeIPXRipForwardType
The type of route. Note that local(2) refers to a route for which the
next hop is the final destination; remote(3) refers to a route
for which the next hop is not the final destination.
Enumerationr/w .1.3.6.1.4.1.164.4.1.5.2.6.1.9
.1.3.6.1.4.1.164.4.1.5.2.7 · 1 row entry · 3 columns
The RIP interface table.
radBridgeIPXRipInfEntry entry .1.3.6.1.4.1.164.4.1.5.2.7.1
Each entry corresponds to one ifindex.
Indexes
No indexes recorded
Column Syntax OID
radBridgeIPXRipInfIfIndex
This value of Ifindex is same as radBridgeIPXIfIndex in the
IPX Interface Table.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.2.7.1.1
radBridgeIPXRipInfBcastUpdate
The RIP periodic update interval, in seconds. Zero value
corresponds to infinite interval.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.2.7.1.2
radBridgeIPXRipInfAgeMultiplier
The holding multiplier for information received in RIP
periodic updates. Zero value corresponds to infinite aging time.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.2.7.1.3
.1.3.6.1.4.1.164.4.1.5.3.6 · 1 row entry · 9 columns
The Server Information table is used by SAP to store information
of services which are available on the internetwork.
radBridgeIPXSapTableEntry entry .1.3.6.1.4.1.164.4.1.5.3.6.1
The server information for one of this entity's server entries.
Indexes
No indexes recorded
Column Syntax OID
radBridgeIPXSapServerType
The type of the server for which this entry pertains.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.3.6.1.1
radBridgeIPXSapName
The name of the server for which this entry pertains.
OctetString
Constraints:
range: 400-3000
.1.3.6.1.4.1.164.4.1.5.3.6.1.2
radBridgeIPXSapNetwork
The IPX network address of the host on which this server exists.
OctetStringr/w
Constraints:
range: 600-4000
.1.3.6.1.4.1.164.4.1.5.3.6.1.3
radBridgeIPXSapNode
The IPX node address of the host on which this server exists.
OctetStringr/w
Constraints:
range: 100-1000
.1.3.6.1.4.1.164.4.1.5.3.6.1.4
radBridgeIPXSapSocket
The IPX socket number that is being used by the server to
which this entry pertains.
SNMPv2-SMIInteger32r/w
Constraints:
range: 0-65535
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.3.6.1.5
radBridgeIPXSapHopsToServer
The number of hops to the entity on which this server exists.
Integer32r/w .1.3.6.1.4.1.164.4.1.5.3.6.1.6
radBridgeIPXSapNIC
An Network Interface Card identifier specifying what IPX
interface the next hop can be found on.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.3.6.1.7
radBridgeIPXSapAgingTime
The last time that the entry was updated. The time will be
provided in terms of the MIB-I object sysUpTime.
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.5.3.6.1.8
radBridgeIPXSapStatus
The status of the entry.
Enumerationr/w .1.3.6.1.4.1.164.4.1.5.3.6.1.9
.1.3.6.1.4.1.164.4.1.5.3.7 · 1 row entry · 3 columns
The Sap interface table.
radBridgeIPXSapInfEntry entry .1.3.6.1.4.1.164.4.1.5.3.7.1
Each entry corresponds to one ifindex.
Indexes
No indexes recorded
Column Syntax OID
radBridgeIPXSapInfIfIndex
This value of Ifindex is same as radBridgeIPXIfIndex in the
IPX Interface Table.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.3.7.1.1
radBridgeIPXSapInfBcastUpdate
The SAP periodic update interval, in seconds. Zero value
corresponds to infinite interval.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.3.7.1.2
radBridgeIPXSapInfAgeMultiplier
The holding multiplier for information received in SAP
periodic updates. Zero value corresponds to infinite aging time.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.5.3.7.1.3
.1.3.6.1.4.1.164.4.1.6.3 · 1 row entry · 24 columns
This is the new masking scheme. 
Mask tables enable definition of forwarding restrictions and 
control of message flow in the internetwork. Each entry
in this table defines a mask statement and an action defined by 
maskingOperation.
maskingEntry entry .1.3.6.1.4.1.164.4.1.6.3.1
Defines the contents of each line in the mask table.
Indexes
No indexes recorded
Column Syntax OID
maskingType
Defines the type of mask entry.
Enumeration
Constraints:
range: 128-128
.1.3.6.1.4.1.164.4.1.6.3.1.1
maskingIfIndex
Specifies the ifIndex of the interface to which the mask is applied.
SNMPv2-SMIInteger32
Constraints:
range: 128-128
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.6.3.1.2
maskingIndex
An index to the masking table. This number should not be greater than maskingMaxEntries
SNMPv2-SMIInteger32
Constraints:
range: 128-128
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.6.3.1.3
maskingProtocolType
The base protocol for masking. IPX, IP, others.
Enumerationr/w
Constraints:
range: 128-128
.1.3.6.1.4.1.164.4.1.6.3.1.4
maskingSmartMaskOID
A reference to a specific Smart mask table (old radBridgeMaskTable)
which enables a more specific mask type.
If this information is not available, its value
should be set to the OBJECT IDENTIFIER { 0 0 }.
ObjectIdentifier .1.3.6.1.4.1.164.4.1.6.3.1.5
maskingFrameType
Enables the user to decide about frame type
* all frame
* just broadcast
* just multicast.
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.6
maskingFrameTypeCondition
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingFrameType the packet contains data that matches
the content of maskingFrameType.…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.7
maskingSourceAddress
The source address is according to the maskingMacOrNet and
maskingProtocolType variables.
In case of 'MAC' enter 6 bytes (48 bit) of source address.
In case of 'NET'
if the maskingProtocolType is IP, this is t…
GenAddressr/w
Textual Convention: GenAddress OctetString
Type Constraints:
range: 12
.1.3.6.1.4.1.164.4.1.6.3.1.8
maskingSourceActiveBits
Specifies the positions of the wild card characters (*)
in the maskingSourceAddress field. Only the 1's bit will be taken in
considerations.
GenAddressr/w
Textual Convention: GenAddress OctetString
Type Constraints:
range: 12
.1.3.6.1.4.1.164.4.1.6.3.1.9
maskingSourceMacOrNet
The variable maskingSourceAddress and maskingSourceActiveBits
will be treated as MAC, or NET address.
- If maskingProtocolType = 'all', 'sna', 'netbios', dec or
'unknown', the maskingSourceMacOrNet can be macAddress…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.10
maskingSourceCondition
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingSourceAddress (in conjunction with maskingSourceActiveBits)
the …
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.11
maskingDestAddress
If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
The destination address is according to the maskingMacOrNet and maskingProto…
GenAddressr/w
Textual Convention: GenAddress OctetString
Type Constraints:
range: 12
.1.3.6.1.4.1.164.4.1.6.3.1.12
maskingDestActiveBits
If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
Specifies the positions of the wild card characters (*)
in the maskingDe…
GenAddressr/w
Textual Convention: GenAddress OctetString
Type Constraints:
range: 12
.1.3.6.1.4.1.164.4.1.6.3.1.13
maskingDestMacOrNet
If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
- If maskingProtocolType = 'all', 'sna', 'netbios', dec or
'unknown', the…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.14
maskingDestCondition
If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
Specifies the logical condition of the mask pattern:

true - …
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.15
maskingLowLevelProt
This field is set in conjunction with the maskingProtocolType variable.
This variable specifies the low level protocol.
The IPX socket entered in maskingDestAddress has priority
over the value of maskingLowLevelProt, w…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.16
maskingLowLevelProtCondition
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingLowLevelProt the packet contains data that matches
the content of maskingLowLeve…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.17
maskingHighLevelProt
This field is set in connection to the maskingProtocolType variable.
This variable specifies the high level protocols (application).
As for today it supports just IP protocol stack.
The object's value is a sum of the fo…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.6.3.1.18
maskingHighLevelProtCondition
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingHighLevelProt the packet contains data that matches
the content of maskingHi…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.19
maskingPortNum
The port number is the same as in high level protocol. It
specifies the dest. port in IP case or the dest. socket
in case of IPX & apple protocols.
IP - This object is applicable only if none (0) value was selecte…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.6.3.1.20
maskingPortNumCondition
Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingPortNum the packet contains data that matches
the content of maskingPortNum.…
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.21
maskingOperation
The type of action to be taken if the frame meets the
conditions of the mask.
noOp = disabled (mask remains on list, but is not active)
delete = mask is removed from the list.
smartMask = the operation and desti…
Enumerationr/w
Constraints:
range: 1-32
.1.3.6.1.4.1.164.4.1.6.3.1.22
maskingSrcPortNum
The source port number.
For IP: No Condition.
For IPX: This object is applicable only if the socket entered in
maskingSourceAddress is don't care (00) and maskingLowLevelProt
is NOT ipxRip or ipxS…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.6.3.1.23
maskingSrcPortNumCondition
The same as 'maskingPortNumCondition'.
Relates to source port.
Enumerationr/w .1.3.6.1.4.1.164.4.1.6.3.1.24
.1.3.6.1.4.1.164.4.1.7.1 · 1 row entry · 14 columns
The RAD Bridge Current table.
radBridgeCurrentEntry entry .1.3.6.1.4.1.164.4.1.7.1.1
An entry in the RAD Bridge Current table.
Indexes
No indexes recorded
Column Syntax OID
radBridgeCurrentIndex
The index of the Bridge interface or Bridge Port.
It may be ifIndex.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.7.1.1.1
radBridgeCurrentIngressFilteringDiscardedFrames
The counter associated with the number of Discarded
Frames upon Ingress Filtering, encountered by a Bridge
interface in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.2
radBridgeCurrentFrameTypeDiscardedFrames
The counter associated with the number of Discarded
Frames upon Frame Type and Tagging Mismatch, encountered
by a Bridge interface in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.3
radBridgeCurrentRxCorrectFrames
The counter associated with the number of Received Correct Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.4
radBridgeCurrentRxCorrectBytes
The counter associated with the number of Received Correct Bytes,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.5
radBridgeCurrentRxCorrectBytesHCOverflow
The counter associated with the number of times the associated
radBridgeCurrentRxCorrectBytes counter has overflowed.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.6
radBridgeCurrentRxBcastFrames
The counter associated with the number of Received Broadcast Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.7
radBridgeCurrentRxMcastFrames
The counter associated with the number of Received Multicast Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.8
radBridgeCurrentTxCorrectFrames
The counter associated with the number of Transmitted Correct Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.9
radBridgeCurrentTxCorrectBytes
The counter associated with the number of Transmitted Correct Bytes,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.10
radBridgeCurrentTxCorrectBytesHCOverflow
The counter associated with the number of times the associated
radBridgeCurrentTxCorrectBytes counter has overflowed.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.11
radBridgeCurrentTxBcastFrames
The counter associated with the number of Transmitted Broadcast Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.12
radBridgeCurrentTxMcastFrames
The counter associated with the number of Transmitted Multicast Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.13
radBridgeCurrentTxDropFrames
The counter associated with the number of Transmitted Dropped Frames,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.1.1.14
.1.3.6.1.4.1.164.4.1.7.2 · 1 row entry · 15 columns
The RAD Bridge Interval table.
radBridgeIntervalEntry entry .1.3.6.1.4.1.164.4.1.7.2.1
An entry in the RAD Bridge Interval table.
Indexes
No indexes recorded
Column Syntax OID
radBridgeIntervalIndex
The index of the bridge interface or Bridge Port.
It may be ifIndex.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.7.2.1.1
radBridgeIntervalNumber
A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).
Integer32 .1.3.6.1.4.1.164.4.1.7.2.1.2
radBridgeIntervalIngressFilteringDiscardedFrames
The counter associated with the number of Discarded
Frames upon Ingress Filtering, encountered by a
Bridge interface in one of the previous 96, individual
15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.3
radBridgeIntervalFrameTypeDiscardedFrames
The counter associated with the number of Discarded
Frames upon Frame Type and Tagging Mismatch, encountered
by a Bridge interface in one of the previous 96, individual
15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.4
radBridgeIntervalRxCorrectFrames
The counter associated with the number of Received Correct Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.5
radBridgeIntervalRxCorrectBytes
The counter associated with the number of Received Correct Bytes,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.6
radBridgeIntervalRxCorrectBytesHCOverflow
The counter associated with the number of times the associated
radBridgeIntervalRxCorrectBytes counter has overflowed.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.7
radBridgeIntervalRxBcastFrames
The counter associated with the number of Received Broadcast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.8
radBridgeIntervalRxMcastFrames
The counter associated with the number of Received Multicast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.9
radBridgeIntervalTxCorrectFrames
The counter associated with the number of Transmitted Correct Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.10
radBridgeIntervalTxCorrectBytes
The counter associated with the number of Transmitted Correct Bytes,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.11
radBridgeIntervalTxCorrectBytesHCOverflow
The counter associated with the number of times the associated
radBridgeIntervalTxCorrectBytes counter has overflowed.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.12
radBridgeIntervalTxBcastFrames
The counter associated with the number of Transmitted Broadcast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.13
radBridgeIntervalTxMcastFrames
The counter associated with the number of Transmitted Multicast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.14
radBridgeIntervalTxDropFrames
The counter associated with the number of Transmitted Dropped Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.7.2.1.15
.1.3.6.1.4.1.164.4.1.8.1 · 1 row entry · 7 columns
A table containing static configuration information for
each VLAN configured into the device by  management.
All entries are permanent and will
be restored after the device is reset.
radBridgePortBaseVlanEntry entry .1.3.6.1.4.1.164.4.1.8.1.1
Static information for a VLAN configured into the
device by (local or network) management.
Indexes
No indexes recorded
Column Syntax OID
radBridgePortBaseVlanCnfgIdx
This object indicates the Idx of the Agent Cnfg the following
objects refer.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this object wil…
Integer32 .1.3.6.1.4.1.164.4.1.8.1.1.1
radBridgePortBaseVlanIdx
Index of the port based VLAN.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.8.1.1.2
radBridgePortBaseVlanName
An administratively assigned string, which may be used
to identify the the port based VLAN.
OctetStringr/w .1.3.6.1.4.1.164.4.1.8.1.1.3
radBridgePortBaseVlanEgressPorts
The set of ports which are permanently assigned to the
egress list for this port based VLAN by management.
The default value of this object is a string of zeros.
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
.1.3.6.1.4.1.164.4.1.8.1.1.4
radBridgePortBaseVlanVirtualGroups
The set of Virtual Groups which are permanently assigned to
this port based VLAN by management.
(read Virtual Group instead of port in PortList Textual Convention)
The default value of this object is a string of zeros.
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
.1.3.6.1.4.1.164.4.1.8.1.1.5
radBridgePortBaseVlanRowStatus
This object enable user to
create/delete entries in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.164.4.1.8.1.1.6
radBridgePortBaseVlanMng
This object allows user to enable/disable
management traffic on this VLAN.
disable - only non-management data is allowed.
enable - mixture of management traffic 0with other
types of data is allowed.
Enumerationr/w .1.3.6.1.4.1.164.4.1.8.1.1.7
.1.3.6.1.4.1.164.4.1.8.2 · 1 row entry · 4 columns
The Bridge Ports-VLAN Membership table.
This table enables the user to assign:
- Several VLANs to a Port.
- Several Ports to a VLAN.
radBridgePortVlanMemberEntry entry .1.3.6.1.4.1.164.4.1.8.2.1
An entry in the Bridge Ports-VLANs Memebership table.
Indexes
No indexes recorded
Column Syntax OID
radBridgePortVlanMemberBridgeIdx
This object indicates the Bridge Index.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.8.2.1.1
radBridgePortVlanMemberPortIdx
This object indicates the Bridge's Port Index.
For some cases, it can be used as the Port ofIndex.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.8.2.1.2
radBridgePortVlanMemberVlanId
This object indicates the VLAN ID.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.8.2.1.3
radBridgePortVlanMemberRowStatus
This object enables the user to
create/delete entries in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.164.4.1.8.2.1.4
.1.3.6.1.4.1.164.4.1.9.1 · 1 row entry · 10 columns
A table containing static configuration information for
Bridge configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.
radBridgeGenFlowEntry entry .1.3.6.1.4.1.164.4.1.9.1.1
Static information for a Bridge configured into the
device by management.
Indexes
No indexes recorded
Column Syntax OID
radBridgeGenFlowCnfgIdx
This object indicates the Idx of the
Agent Cnfg the following objects refer.
255=Temporary Cnfg (when relevant Set is done
only to this configuration).
For Agents that support only one configuration,
this object will be…
Integer32 .1.3.6.1.4.1.164.4.1.9.1.1.1
radBridgeGenFlowIdx
For Agent having more than one bridge,
this index may be used as bridge index
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.1.1.2
radBridgeGenFlowRowStatus
This object enable user to
create/delete entries in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.164.4.1.9.1.1.3
radBridgeGenFlowFloodOrBcastMaxRate
This object controls maximum Flooding or Broadcast Rate:
Max number of multicast along with unknown
or flooded unicast frames allowed to enter
any port.
The number can be presented either as percentage of bandwidth, or …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.1.1.4
radBridgeGenFlowQosMode
This object controls Quality of Service mode.
User may select which field(s)
(in case of fields - which one has precedence)
will affect prioritization of data between egress queues.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.1.1.5
radBridgeGenFlowSchedulingMode
This object controls which scheduling mode is used.
hqpAndWrr(6) - The highest queue will be emptied first, then the
other queues, according to WRR (Weighted Round Robin).
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.1.1.6
radBridgeGenFlowBasicClassification
This object defines whether Classification based on Port should be
taken into account (either as default, or in addition to other
classifications).
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.1.1.7
radBridgeGenFlowMulticastTrafficClass
The Traffic Class the received Multicast frame is mapped to.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.1.1.8
radBridgeGenFlowBroadcastTrafficClass
The Traffic Class the received Broadcast frame is mapped to.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.1.1.9
radBridgeGenFlowUnkownUnicastTrafficClass
The Traffic Class the received
Unkonwn Unicast frame is mapped to.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.1.1.10
.1.3.6.1.4.1.164.4.1.9.2 · 1 row entry · 4 columns
A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.
radBridgeDot1qVlanStaticEntry entry .1.3.6.1.4.1.164.4.1.9.2.1
Static information for a VLAN configured into the
device by (local or network) management.
Indexes
No indexes recorded
Column Syntax OID
radBridgeDot1qVlanTaggedPorts
The set of ports which should transmit egress packets
for this VLAN as tagged.
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
.1.3.6.1.4.1.164.4.1.9.2.1.1
radBridgeDot1qVlanUnmodifiedPorts
The set of ports which should transmit egress packets
for this VLAN as unmodified.
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
.1.3.6.1.4.1.164.4.1.9.2.1.2
radBridgeDot1qVlanSplitHorizon
When 'enable (3)', packets having this VLAN will
not be switched back to other bridge ports which are
members of this VLAN.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.2.1.3
radBridgeDot1qVlanRingMembers
This object indicates which Ring (ERP=Ethernet Ring Protection)
are members of this VLAN. For each BIT, the value means:
'1' = Ring is member of this VLAN.
'0' = Ring is NOT member of this VLAN.
Bitsr/w .1.3.6.1.4.1.164.4.1.9.2.1.4
.1.3.6.1.4.1.164.4.1.9.3 · 1 row entry · 9 columns
A table containing control and status
information for VLAN configuration per port.
radDot1qPortVlanEntry entry .1.3.6.1.4.1.164.4.1.9.3.1
Information controlling VLAN configuration for a port.
This is indexed by dot1dBasePort.
Indexes
No indexes recorded
Column Syntax OID
radDot1qPortStacking
This object indicates the port stacking operation:
unmodify (2) = Do not add Tag.
tag (3) = Add Tag to Untagged Frames.
stack (4) = Add Tag to all Frames.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.1
radDot1qPortCopyOriginVlanPriority
This object indicates whether use the original VLAN Priority of the frame,
as the priority of the VLAN added by this port.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.2
radDot1qPortDefaultVlanPriority
Default VLAN Frame priority of the VLAN added by this port.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.3.1.3
radDot1qPortTagStripping
This object indicates whether remove a tag from the frame on this port,
frame with double tag will remain with one tag and frame with
one tag will remain untagged.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.4
radDot1qPortEgressTagHandling
This object indicates how is the Egress VLAN Tag processed.
It is mainly for use with Double Tagging.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.5
radDot1qPortIngressTagHandling
This object indicates how is the Ingress VLAN Tag processed.
It is mainly for use with Double Tagging.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.6
radDot1qPortReplaceVlanPriority
This object indicates whether for each received tagged frame on this Bridge Port -
VLAN Priority will be replaced by another Priority.
no(2) = no repacement
yes(3) = VLAN Priority will be replaced

Fo…
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.7
radDot1qPortVlanEthType
This object indicates the Ethernet Type.
For some devices, it is applicable only when radDot1qPortStacking = stack.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.9.3.1.8
radDot1qPortVlanCnodeLevel1Agent
Specify if a Level 1 cNode agent is enabled or not for the bridge port.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.3.1.9
.1.3.6.1.4.1.164.4.1.9.4 · 1 row entry · 9 columns
A table containing Bridge configuration parameters.
radBridgeGenCfgEntry entry .1.3.6.1.4.1.164.4.1.9.4.1
Describes an entry in the radBridgeGenCfgTable.
Indexes
No indexes recorded
Column Syntax OID
radBridgeGenCfgIdx
This object indicates the Idx of the
Agent Cnfg the following objects refer.
255=Temporary Cnfg.
For Agents that support only one Configuration,
this object will be constant=1.
Integer32 .1.3.6.1.4.1.164.4.1.9.4.1.1
radBridgeGenCfgIdx2
For Agents having more than one bridge,
this index may be used as bridge index
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.9.4.1.2
radBridgeGenCfgBridgeAction
This variable enables the operator to perform one of the
specified actions on the tables maintained by the Bridge.
After performing the action, Agent will automatically
Set the value of this variable to noOp(255).
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.4.1.3
radBridgeAgingTimeSec
This variable duplicates scalar object
dot1dTpAgingTimeThe of BRIDGE-MIB with configuration index
and Bridge index.

It defines the timeout period in seconds for aging out
dynamically learned forwarding in…
Integer32r/w .1.3.6.1.4.1.164.4.1.9.4.1.4
radBridgeMngVlanId
This variable indicates the VLAN ID
used for remote management traffic.
0 = Not Applicable.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.9.4.1.5
radBridgeLoopDetectVlanId
This variable indicates the VLAN ID used for Loop Detection packets.
Valid values:
1 - 4095: VLAN ID
0 - Means that the Loop Detection is Disabled.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.9.4.1.6
radBridgeSplitHorizon
This object configure 'split horizon' switching between bridge Ports.
- disable - normal (VLAN aware) bridge behavior.
- enable - all packets, regardless their VLAN, coming from user side
are blocked from being switch…
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.4.1.7
radBridgeEthType
Value of Ethertype field in Ethernet frame.
This field indicates which protocol is being transported
in an ethernet frame.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.9.4.1.8
radBridgeTopology
This object indicates the topology type of the Bridge.
The default is E-LAN (2)
BridgeTopologyr/w
Textual Convention: BridgeTopology Enumeration
Type Values:
1notApplicable
3eLAN
4eTree
.1.3.6.1.4.1.164.4.1.9.4.1.9
.1.3.6.1.4.1.164.4.1.9.7 · 1 row entry · 4 columns
A table containing static configuration information for
each VLAN configured into the device by (local or network)
management.
All entries are permanent and are restored after the device
reset.
The table is similar to radBridgeDot1qVlanStaticTable, but
supports multiple bridges.
ieee8021QBridgeVlanStaticXEntry entry .1.3.6.1.4.1.164.4.1.9.7.1
Static information for a VLAN configured into the
device by (local or network) management.
Indexes
No indexes recorded
Column Syntax OID
ieee8021QBridgeVlanStaticXSplitHorizon
When 'enable (3)', packets having this VLAN will
not be switched back to other bridge ports which are
members of this VLAN.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.7.1.3
ieee8021QBridgeVlanStaticXRingMembers
A sixteen-octet(128 bit) pattern: This object indicates which Ring (ERP=Ethernet Ring Protection)
are members of this VLAN. For each BIT, the value means:
'1' = Ring is member of this VLAN.
OctetStringr/w .1.3.6.1.4.1.164.4.1.9.7.1.4
ieee8021QBridgeVlanStaticXMaxMacAddr
This object indicates the maximum number of MAC addresses
supported by this VLAN.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.9.7.1.8
ieee8021QBridgeVlanStaticXTopology
This object indicates the bridge topology per VLAN.
The default is E-LAN (2)
BridgeTopologyr/w
Textual Convention: BridgeTopology Enumeration
Type Values:
1notApplicable
3eLAN
4eTree
.1.3.6.1.4.1.164.4.1.9.7.1.9
.1.3.6.1.4.1.164.4.1.9.9 · 1 row entry · 5 columns
A table containing Bridge configuration parameters
of the management traffic.
radBridgePortVlanEntry entry .1.3.6.1.4.1.164.4.1.9.9.1
Describes an entry in the radBridgePortVlanTable.
Indexes
No indexes recorded
Column Syntax OID
radBridgePortVlanBridgeIdx
This object indicates the Idx of the bridge.
IEEE8021-TC-MIBIEEE8021PbbComponentIdentifier
Textual Convention: IEEE8021-TC-MIBIEEE8021PbbComponentIdentifier Unsigned32
Type Constraints:
range: 1..4294967295
.1.3.6.1.4.1.164.4.1.9.9.1.1
radBridgePortVlanIdx
- For VLAN Aware :
This object indicates the VLAN ID number.
- For VLAN Unaware:
This object is not applicable and the value shall be 0xFFFFFFFF = Not Applicable.
IEEE8021-TC-MIBIEEE8021VlanIndex
Textual Convention: IEEE8021-TC-MIBIEEE8021VlanIndex Unsigned32
Type Constraints:
range: 1..4094
range: 4096..4294967295
.1.3.6.1.4.1.164.4.1.9.9.1.2
radBridgePortVlanPrtIdx
This object indicates the bridge port Idx.
IEEE8021-TC-MIBIEEE8021BridgePortNumber
Textual Convention: IEEE8021-TC-MIBIEEE8021BridgePortNumber Unsigned32
Type Constraints:
range: 1..65535
.1.3.6.1.4.1.164.4.1.9.9.1.3
radBridgePortVlanRowStatus
This object enables creation and deletion of entries
in the radBridgePortVlanTable.
Leaf nodes of E-TREE topology will not be registered
in this table (see object radBridgePortVlanIsRoot).
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.164.4.1.9.9.1.4
radBridgePortVlanIsRoot
This object indicates if the node is Root port
or Leaf port.
By default:
- for E-LAN topology all nodes are root.
- for E-TREE topology all nodes that are leaves will
not be registered.
Enumerationr/w .1.3.6.1.4.1.164.4.1.9.9.1.5
.1.3.6.1.4.1.164.4.1.10.1 · 1 row entry · 2 columns
An inversed table to dot1dBasePortTable 
from RFC1493 with reduced information.
This table index is known to the NMS and 
this way the needed information can be received
by just one Get command, instead of searching 
the entire dot1dBasePortTable (where it is an 
attribute).
radBridgeInvBasePortEntry entry .1.3.6.1.4.1.164.4.1.10.1.1
The bridge port number for each bridge port
interface index.
Indexes
No indexes recorded
Column Syntax OID
radBridgeInvBasePortIfIndex
The value of the instance of the ifIndex object,
defined in MIB-II, for the interface corresponding
to this Bridge port.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.10.1.1.1
radBridgeInvBasePort
The Bridge port number.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.10.1.1.2
.1.3.6.1.4.1.164.4.1.10.2 · 1 row entry · 6 columns
Table that allow to find specific MAC address in a bridge
its allow to search:
- specific Mac address in a bridge
- Mac addresses on a VLAN
- Mac addresses on a port.
bridgeMacSearchEntry entry .1.3.6.1.4.1.164.4.1.10.2.1
Entries define list of MAC and VLAN per bridge.
Indexes
No indexes recorded
Column Syntax OID
bridgeMacSearchIdx
Value is always equal to 1.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.2.1.1
bridgeMacSearchBridgeComponentId
The Mac address to search in a specific bridge.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.2.1.2
bridgeMacSearchAddress
The Mac address to search in a specific bridge.
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
.1.3.6.1.4.1.164.4.1.10.2.1.3
bridgeMacSearchVlan
The object is used to search all the MAC addresses in a specific VLAN.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.2.1.4
bridgeMacSearchPort
The object is used to search all the MAC addresses in a specific port.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.2.1.5
bridgeMacSearchCmdStatus
The status of the search process:
notApplicable - used as default value
startSearch - initiate search process
macSearching - search is in process
macFound - the search was end with a result
macNoFound - the s…
Enumerationr/w .1.3.6.1.4.1.164.4.1.10.2.1.6
.1.3.6.1.4.1.164.4.1.10.3 · 1 row entry · 5 columns
The table holds the result of the searching MAC addresses
initiated in table bridgeMacTable.
bridgeMacResultEntry entry .1.3.6.1.4.1.164.4.1.10.3.1
Describes an entry in the bridgeMacResultTable.
Indexes
No indexes recorded
Column Syntax OID
bridgeMacResultBridgeIdx
The bridge index.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.3.1.1
bridgeMacResultVlan
The Mac address on a VLAN that was searched.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.3.1.2
bridgeMacResultMacAddress
The Mac address that was searched.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
.1.3.6.1.4.1.164.4.1.10.3.1.3
bridgeMacResultPort
The Mac address on a port that was searched.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.10.3.1.4
bridgeMacResultCmdStatus
The type of the Mac address, see ieee8021QBridgeTpFdbStatus for details.
Enumeration .1.3.6.1.4.1.164.4.1.10.3.1.5
.1.3.6.1.4.1.164.4.1.11.1 · 1 row entry · 7 columns
STP Configuration table. STP=Spanning Tree Protocol.  
It includes STP configurable parameters that in BRIDGE-MIB 
are scalars, while we need them per card/bridge/interface
	 and per different configurations.
radBridgeStpCnfgEntry entry .1.3.6.1.4.1.164.4.1.11.1.1
An entry in the radBridgeStpCnfgTable.
Indexes
No indexes recorded
Column Syntax OID
radBridgeStpCnfgIdx1
This object indicates the Index of the Agent Configuration
the following objects refer to.
For Agents that support more than one configuration:
255=Temporary Cnfg ; Set can be done only to this configuration.
For A…
Integer32 .1.3.6.1.4.1.164.4.1.11.1.1.1
radBridgeStpCnfgIdx2
For Agents having the table objects per Card/Bridge/Interface
this will be the index of the Card/Bridge/Interface used.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.11.1.1.2
radBridgeStpCnfgForwardDelay
The value that the bridge of radBridgeStpCnfgIdx2 uses for
Forward Delay when this bridge is acting as the root. Note that
the range for this parameter is related to the value of
radBridgeStpCnfgMaxAge (according to 8…
Integer32r/w .1.3.6.1.4.1.164.4.1.11.1.1.3
radBridgeStpCnfgMaxAge
The value that the bridge of radBridgeStpCnfgIdx2 uses for
MaxAge when this bridge is acting as the root. Note that
the range for this parameter is related to the value of
radBridgeStpCnfgHelloTime (according to 802.1…
Integer32r/w .1.3.6.1.4.1.164.4.1.11.1.1.4
radBridgeStpCnfgHelloTime
The value that the bridge of radBridgeStpCnfgIdx2 uses for
Hello Time when this bridge is acting as the root. The granularity
of this timer is specified by 802.1D-1990 to be 1 second. An agent
may return a badValue …
Integer32r/w .1.3.6.1.4.1.164.4.1.11.1.1.5
radBridgeStpCnfgPriority
The value of the write-able portion of the Bridge ID, i.e., the first
two octets of the (8 octet long) Bridge ID, per radBridgeStpCnfgIdx2
instance.
Integer32r/w .1.3.6.1.4.1.164.4.1.11.1.1.6
radBridgeStpCnfgStpVersion
This object determines the STP version used:
stp - usual Spanning Tree Protocol.
rstp - Rapid Spanning Tree Protocol.
Enumerationr/w .1.3.6.1.4.1.164.4.1.11.1.1.7
.1.3.6.1.4.1.164.4.1.11.2 · 1 row entry · 6 columns
STP Status table. STP=Spanning Tree Protocol.
It includes STP status parameters that in BRIDGE-MIB 
are scalars, while we need them per card/bridge/interface.
For devices that have several configurations, this table is for Status
of the Active configuration.
radBridgeStpStatEntry entry .1.3.6.1.4.1.164.4.1.11.2.1
An entry in the radBridgeStpStatTable.
Indexes
No indexes recorded
Column Syntax OID
radBridgeStpStatIdx
For Agents having the table objects per Card/Bridge/Interface
this will be the index of the Card/Bridge/Interface used.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.11.2.1.1
radBridgeStpStatForwardDelay
This time value, measured in units of hundredths of a second,
controls how fast a port changes its spanning state when moving
towards the Forwarding state. The value determines how long the port
stays in each of the …
BRIDGE-MIBTimeout
Textual Convention: BRIDGE-MIBTimeout Integer32
.1.3.6.1.4.1.164.4.1.11.2.1.2
radBridgeStpStatMaxAge
The maximum age of Spanning Tree Protocol information learned
from the network on any port before it is discarded, in units
of hundredths of a second. This is the actual value that this
bridge is currently using.
BRIDGE-MIBTimeout
Textual Convention: BRIDGE-MIBTimeout Integer32
.1.3.6.1.4.1.164.4.1.11.2.1.3
radBridgeStpStatHelloTime
The amount of time between the transmission of Configuration
bridge PDUs by this node on any port when it is the root of
the spanning tree or trying to become so, in units of hundredths
of a second. This is the actua…
BRIDGE-MIBTimeout
Textual Convention: BRIDGE-MIBTimeout Integer32
.1.3.6.1.4.1.164.4.1.11.2.1.4
radBridgeStpStatDesignatedRoot
The bridge identifier of the root of the spanning tree as determined
by the Spanning Tree Protocol as executed by this node. This value
is used as the Root Identifier parameter in all Configuration
Bridge PDUs origin…
BRIDGE-MIBBridgeId
Textual Convention: BRIDGE-MIBBridgeId OctetString
Type Constraints:
range: 8
.1.3.6.1.4.1.164.4.1.11.2.1.5
radBridgeStpStatRootCost
The cost of the path to the root as seen from this bridge.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.11.2.1.6
.1.3.6.1.4.1.164.4.1.11.3 · 1 row entry · 4 columns
ieee8021MstpXTable augments ieee8021MstpTable.
It is used for mapping VLANs to MST instances..
ieee8021MstpXEntry entry .1.3.6.1.4.1.164.4.1.11.3.1
An entry in the ieee8021MstpXTable.
Indexes
No indexes recorded
Column Syntax OID
ieee8021MstpXVids0
This object contains the first 1024 bits of the 4096 bit vector
indicating which VIDs are assigned to this MSTID. This is a read-writable
object corresponding to ieee8021MstpVids0.
OctetStringr/w .1.3.6.1.4.1.164.4.1.11.3.1.1
ieee8021MstpXVids1
This object contains the first 1024 bits of the 4096 bit vector
indicating which VIDs are assigned to this MSTID. This is a read-writable
object corresponding to ieee8021MstpVids0.
OctetStringr/w .1.3.6.1.4.1.164.4.1.11.3.1.2
ieee8021MstpXVids2
This object contains the third 1024 bits of the 4096 bit vector
indicating which VIDs are assigned to this MSTID. This is a read-writable
object corresponding to ieee8021MstpVids2
OctetStringr/w .1.3.6.1.4.1.164.4.1.11.3.1.3
ieee8021MstpXVids3
This object contains the fourth 1024 bits of the 4096 bit vector
indicating which VIDs are assigned to this MSTID. This is a read-writable
object corresponding to ieee8021MstpVids3
OctetStringr/w .1.3.6.1.4.1.164.4.1.11.3.1.4
.1.3.6.1.4.1.164.4.1.13.1 · 1 row entry · 12 columns
The Bridge Port Configuration Table.
radBridgePortCnfgEntry entry .1.3.6.1.4.1.164.4.1.13.1.1
An entry in the table.
Indexes
No indexes recorded
Column Syntax OID
radBridgePortCnfgIdx
The first index of the table.
It can serve for Configuration index, Bridge index or other.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.1
radBridgePortCnfgPrtIdx
This object indicates the Bridge Port index.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.2
radBridgePortCnfgMaxMacAddr
This object indicates the maximum number of total MAC Addresses
(static and learned) supported by this Bridge Port.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.3
radBridgePortCnfgMngFlow
This object indicates whether this Bridge Port
is dedicated for management flow.
Enumerationr/w .1.3.6.1.4.1.164.4.1.13.1.1.4
radBridgePortCnfgMcastMode
This object indicates this Bridge Port's Multicast Mode:
flooding (1) - flood multicast MAC addresses
forwarding (2) - forward multicast MAC addresses to the subnet indicated.
Enumerationr/w .1.3.6.1.4.1.164.4.1.13.1.1.5
radBridgePortCnfgDefaultVpi
This object indicates the VPI of this Bridge Port's Default VCL.
An incoming frame with priority that is not assigned to any VCL
will be transferred to the Default VCL.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.6
radBridgePortCnfgDefaultVci
This object indicates the VCI of this Bridge Port's Default VCL.
An incoming frame with priority that is not assigned to any VCL
will be transferred to the Default VCL.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.7
radBridgePortCnfgStatVlanId
This object indicates the selected VlanId of the bridge port
on which statistics are being collected.
0=no Statistics collected for VLAN on this bridge port.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.8
radBridgePortCnfgIngressMtu
The size of the largest packet which can be received
on the interface, specified in octets.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.9
radBridgePortCnfgEgressMtu
The size of the largest packet which can be sent
on the interface, specified in octets.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.10
radBridgePortCnfgDot1x
This feature is currently supported via the variable ethIfTable.ethDot1xEnable.
Determnines if the Port-Based Network Access Protocol
(IEEE-802.1x)is enabled for the bridge Port.
Enumerationr/w .1.3.6.1.4.1.164.4.1.13.1.1.11
radBridgePortCnfgMappingProfile
This attribute defines the Queue Mapping Profile ID(cosProfileTable) assigned
to this Bridge Port.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.4.1.13.1.1.12
.1.3.6.1.4.1.164.4.1.14 · 1 row entry · 2 columns
A RAD-defined list of objects containing information for
each bridge. This table augments ieee8021BridgeBaseTable.
ieee8021BridgeBaseXEntry entry .1.3.6.1.4.1.164.4.1.14.1
This is indexed by ieee8021BridgeBaseComponentId.
Indexes
No indexes recorded
Column Syntax OID
ieee8021BridgeBaseXForwardingMode
This object is similar with radBridgeForwardingMode.
It determines the Bridge Forwarding Mode:
transparent - Forward all frames received (not dependent on VLAN).
filter - Filter frames received according to MAC Address…
Enumerationr/w .1.3.6.1.4.1.164.4.1.14.1.1
ieee8021BridgeBaseXName
This object indicates the Bridge's Name.
OctetStringr/w .1.3.6.1.4.1.164.4.1.14.1.2
.1.3.6.1.4.1.164.4.1.15 · 1 row entry · 4 columns
A Reverese table of ieee8021QBridgeVlanCurrentTable.
invieee8021QBridgeVlanCurrentEntry entry .1.3.6.1.4.1.164.4.1.15.1
Information for an FDB ID configured into the device.
Indexes
No indexes recorded
Column Syntax OID
invieee8021QBridgeVlanCurrentComponentId
The component identifier is used to distinguish between the
multiple virtual bridge instances within a PBB. In simple
situations where there is only a single component the default
value is 1.
IEEE8021-TC-MIBIEEE8021PbbComponentIdentifier
Textual Convention: IEEE8021-TC-MIBIEEE8021PbbComponentIdentifier Unsigned32
Type Constraints:
range: 1..4294967295
.1.3.6.1.4.1.164.4.1.15.1.1
invieee8021QBridgeVlanFdbId
The Filtering Database used by this VLAN. This is one
of the ieee8021QBridgeFdbId values in the ieee8021QBridgeFdbTable.
This value is allocated automatically by the device whenever
the VLAN is created: either dynamica…
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.4.1.15.1.2
invieee8021QBridgeVlanTimeMark
A TimeFilter for this entry. See the TimeFilter
textual convention to see how this works.
RMON2-MIBTimeFilter
Textual Convention: RMON2-MIBTimeFilter Unsigned32
.1.3.6.1.4.1.164.4.1.15.1.3
invieee8021QBridgeVlanIndex
The VLAN-ID or other identifier referring to this VLAN.
IEEE8021-TC-MIBIEEE8021VlanIndex
Textual Convention: IEEE8021-TC-MIBIEEE8021VlanIndex Unsigned32
Type Constraints:
range: 1..4094
range: 4096..4294967295
.1.3.6.1.4.1.164.4.1.15.1.4