mcTrapLParam1 = command <upload=1, download=2, apply=3, confirm=4, save=5>;
mcTrapLParam2 = filetype <pattern=1, private=2, binary=3>
mcTrapDescr = Description of operarion:
    DeviceName, 
    command <upload, download, apply, confirm, save>, 
    tftp host,
    config filename,
    status=Error,
    cause of error

mcTrapLParam1 = command <upload=1, download=2, apply=3, confirm=4, save=5>;
mcTrapLParam2 = filetype <pattern=1, private=2, binary=3>
mcTrapDescr = Description of operarion:
    DeviceName, 
    command <upload, download, apply, confirm, save>, 
    tftp host,
    config filename,
    status=Ok

mc-240 stream alarm trap. Severity: alert

mc240 sensor alarm trap (mcTrapExState = sensors bit mask, param1=temp,C, param2=Hum,%)

dslam link down trap (mcTrapExState = link state, param1 = ADSLport)

Downstream rate for dslam ADSL port change (mcTrapExState = 2-increase 1-decrease, param1 = ADSLport)

Downstream rate for dslam ADSL port change (mcTrapExState = 2-increase 1-decrease, param1 = ADSLport)

Bad registration ONU Event (mcTrapLParam1=Optical Interface Number, mcTrapDescr='description with MAC addr ONU')

Eth Link Down, mcTrapLParam1=Link Number, Description='GePON: Eth Link N down'

The optical link N (mcTrapLParam1) has no active devices

overheat (mcTrapExState = 1 -> DSP, = 2 -> PWR, param1 = val of temp * 10)

when voltage deviation become more 10% (param1 = number of voltage nominal mean  12, -12, 3.3, 2.5, 1.8, 1.25, 1.5, 1 correspondly, param2 - whole number part temperature value, param3 - decimal part  temperature value )

Trap sending when connection happen, mcTrapLParam1 - means connection from (0)-CLI (1)->Webs (2)->SNMP

mc-240 sync alarm trap. Severity: warning

Trap sending when switch port link DOWN, mcTrapLParam1 - means port num:
for mxa: 0 - p0; 1 - p1; 2 - p2; 3 - cpu; 4 - dsl0; 5 - sfp;  6 - dsl1;
for asl: 0 - lan;                3 - cpu; 4 - dsl0; 5 - dsl1; 6 - s0; 7 - s1

mc-240 ss7 link alarm trap. Severity: alert

mc-240 ss7 linkset alarm trap. Severity: critical

mc-240 file alarm trap. Severity: critical

mc-240 card alarm trap. Severity: critical

mxl DSL DP system alarm trap

mxl DSL DP system alarm trap

mc240 UPS alarm trap

mc-240 stream ok trap. Severity: alert

mc240 sensor alarm trap (normal state)

dslam link up trap (mcTrapExState = link state == 0, param1 = ADSLport)

Downstream rate for dslam ADSL port change (mcTrapExState = 0-reate not change, param1 = ADSLport)

Downstream rate for dslam ADSL port change (mcTrapExState = 0-reate not change, param1 = ADSLport)

Normal registration ONU Event (mcTrapLParam1=Optical Interface Number, mcTrapDescr='description with MAC addr ONU')

Eth Link Up, mcTrapLParam1=Link Number, Description='GePON: Eth Link N up'

The optical link N (mcTrapLParam1) has M (mcTrapLParam2) active devices

overheat (mcTrapExState = 1 -> DSP, = 2 -> PWR, param1 = val of temp * 10)

when voltage deviation become less 10% (param1 = number of voltage nominal mean  12, -12, 3.3, 2.5, 1.8, 1.25, 1.5, 1 correspondly, param2 - whole number part temperature value, param3 - decimal part  temperature value )

Trap sending when connection closed, mcTrapLParam1 - means disconnection from (0)-CLI (1)->Webs (2)->SNMP

mc-240 sync ok trap. Severity: warning

Trap sending when switch port link UP, mcTrapLParam1 - means port num:
for mxa: 0 - p0; 1 - p1; 2 - p2; 3 - cpu; 4 - dsl0; 5 - sfp;  6 - dsl1;
for asl: 0 - lan;                3 - cpu; 4 - dsl0; 5 - dsl1; 6 - s0; 7 - s1

mc-240 ss7 link ok trap. Severity: alert

mc-240 ss7 linkset ok trap. Severity: critical

mc-240 file ok trap. Severity: critical

mc-240 card trap. Severity: critical

mxl DSL DP system alarm trap (normal state)

mxl DSL DP system alarm trap (normal state)

mc240 UPS alarm trap (normal state)

MP operation error.

Battery cell voltage spread is out of range.

AC voltage is out of range.

Battery is close to total discharge.

Load current is out of range.

Battery charge current is too high.

Power supply from battery.

Battery is disconnected from MPs' output.

Incorrect input parameters.

UEP configuration error.

Temperature measurement error.

ACV measurement error.

Battery current measurement error.

Battery voltage measurement error.

Can't change (increase or decrease) battery voltage.

Release device is off (battery disconnected).

MP operation OK.

Battery cell voltage spread is in range.

AC voltage is in range.

Battery charge status is OK.

Load current is in range.

Battery charge current is in range.

Power supply from MPs.

Battery is connected to MPs' output.

Input parameters OK.

UEP configuration OK.

Temperature measurement OK.

ACV measurement OK.

Battery current measurement OK.

Battery voltage measurement OK.

Battery voltage changing OK.

Release device is on.