DPW-ATM-MIB Table View

This table specifies generic information for an ATM PW
to be carried over PSN in any mode.

dpwAtmCfgEntry row .0.1.1.1.1

This table contains a set of parameters for
the ATM PW that needs to be adapted and carried
over PSN. This table is indexed by pwIndex from
pwTable. An entry is created for every newly pwIndex
in the pwTable. Unless oth…

Indexes

PW-STD-MIBpwIndex

Column	Syntax	OID
dpwAtmCfgMaxCellConcatenation The maximum number of ATM cells that can be concatenated into one PW packet towards PSN. In non LDP or other signaling protocol environment, this object MAY be changed at anytime, but traffic might be interuppted, other…	Unsigned32r/w Constraints: range: 1-29	.0.1.1.1.1.1
dpwAtmCfgFarEndMaxCellConcatenation The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If no LDP in use, the object will either return value 0 or allow setting it for calculating protocol ov…	Unsigned32 Constraints: range: 1-29	.0.1.1.1.1.2
dpwAtmCfgTimeoutMode This objects determines whether a packet can be transmitted to the PSN based on time out expiration for collecting cells or not. The actual handling of the time out is implementation specific-as such this object may be …	Enumerationr/w Enumerated Values: 1 notApplicable 2 disabled 3 enabled	.0.1.1.1.1.3
dpwAtmMaxCellConcatenationTimer This timer is used to concatenate the maximum ATM cell packets in the configured timer value. The unit of the timer is in microseconds.	Unsigned32r/w Constraints: range: 300-4095	.0.1.1.1.1.4

This table specifies the information for an ATM PW to
be carried over PSN in the outbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
  An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following: atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3).

dpwAtmOutboundNto1Entry row .0.1.1.2.1

A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFF…

Indexes

PW-STD-MIBpwIndex dpwAtmOutboundNto1AtmIf dpwAtmOutboundNto1Vpi

Column	Syntax	OID
dpwAtmOutboundNto1AtmIf The ATM Interface that receives cells from the ATM network.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.0.1.1.2.1.1
dpwAtmOutboundNto1Vpi VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.0.1.1.2.1.2
dpwAtmOutboundNto1RowStatus This Object is used to create, modify or delete a row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.0.1.1.2.1.3
dpwAtmOutboundNto1MappedVpi The egress generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFF…	Enumerationr/w Enumerated Values: 0 disable 1 enable	.0.1.1.2.1.4
dpwAtmOutboundNto1OntId This object specifies the identification of an ONT.	OctetStringr/w Constraints: range: 0-255	.0.1.1.2.1.5

This table specifies the information for an ATM PW to
be carried over PSN in the Inbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
  An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following:atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3).

dpwAtmInboundNto1Entry row .0.1.1.3.1

A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFF…

Indexes

PW-STD-MIBpwIndex dpwAtmInboundNto1AtmIf dpwAtmInboundNto1Vpi

Column	Syntax	OID
dpwAtmInboundNto1AtmIf The ATM Interface that receives cells from the ATM network.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.0.1.1.3.1.1
dpwAtmInboundNto1Vpi VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.0.1.1.3.1.2
dpwAtmInboundNto1RowStatus This Object is used to modify or delete a row in this table. This table is associated with dpwAtmOutboundNto1Table. So a row can be created in this table through dpwAtmOutboundNto1Table	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.0.1.1.3.1.3
dpwAtmInboundNto1MappedVpi The generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Val…	Enumerationr/w Enumerated Values: 0 disable 1 enable	.0.1.1.3.1.4

This table contains the ONT downstream VCI-EXP qos mapping
parameters. This  exp value represents the queue-type in 
exp-queue table

dpwAtmVciExpEntry row .0.1.1.4.1

An entry in this table is created for downstream ont qos.

Indexes

dpwAtmOntid dpwAtmVpi dpwAtmExpVci

Column	Syntax	OID
dpwAtmOntid This object represents the identification of an ONT.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.4.1.1
dpwAtmVpi This object represents the downstream ont qos vpi value.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.4.1.2
dpwAtmExpVci The downstream ont qos vci value for corresponding vpi.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.4.1.3
dpwAtmVciExp The exp value representing exp-queue table for downstream ont qos.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.4.1.4
dpwAtmExpRowStatus This vci-exp table supports only exp value modification. This object becomes active with default exp value when vci-qos table entries are created. This Object is for internal use only and not configurable by user.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.4.1.5

This table contains the downstream ont qos EXP Queue related parameters.

dpwAtmExpQosEntry row .0.1.1.5.1

An entry in this table is created for downstream ont qos with queue-type
for corresponfing exp .

Indexes

dpwAtmOntid dpwAtmQosExp

Column	Syntax	OID
dpwAtmQosExp This object specifies the exp value corresponding to downstream ont qos.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.5.1.1
dpwAtmExpQosMode This obejct specifies the exp queue-type for downstream ont qos .	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.5.1.2
dpwAtmExpQosPriority This object specifes the priority for queue-type of strict priority(SP).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.5.1.3
dpwAtmExpQosWeight This object specifies the weight for queue-type of weighted round robin(WRR).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.5.1.4
dpwAtmExpQosRowStatus This Object is for internal use only and not configurable by user. This table will have default values unless modified by the user.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.5.1.5

This table contains VCI Queue related parameters for upstream ont qos.

dpwAtmVciQosEntry row .0.1.1.6.1

An entry in this table is created for upstream ont qos vci-qos.

Indexes

dpwAtmOntid dpwAtmVpi dpwAtmExpVci

Column	Syntax	OID
dpwAtmVciQosClass This objects specifies class type for upstream ont qos vci.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.0.1.1.6.1.1
dpwAtmVciQosPCR This object specifies the peak cell rate for corresponding upstream ont qos.This value should be in a multiples of 151 only	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.6.1.2
dpwAtmVciQosSCR This object specifies the substainable cell rate for upstream ont qos.This value should be in a multiples of 151 only	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.6.1.3
dpwAtmVciQosMBS This object specifies maximum burst size of corresponding vci in upstream ont qos.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.6.1.4
dpwAtmVciQosCDVT This object specifies cell delay variance tolerance corresponds to vci in upstream ont qos.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.6.1.5
dpwAtmVciQosRowStatus This Object is used to create and delete a row in this table. When the Row status is active, whenever user configures in OLT, ONT is also configured. For row creation, user is suggested to configure the qos parameters a…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.6.1.6

The current 15 minute interval counts are in
this table.
This table provides performance information per ATM PW.

dpwAtmPerfCurrentEntry row .0.1.1.7.1

An entry in this table is created by the agent for every
pwAtmCfgTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwAtmPerfInterval table and the counts in this entry
are …

Indexes

PW-STD-MIBpwIndex

Column	Syntax	OID
dpwAtmPerfCurrentMissingPkts Number of missing packets (as detected via control word sequence number gaps).	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.1
dpwAtmPerfCurrentPktsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.2
dpwAtmPerfCurrentPktsMisOrder Number of packets detected out of order (via control word sequence numbers).	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.3
dpwAtmPerfCurrentPktsTimeout Number of packets transmitted due to timeout expiration while attempting to collect cells.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.4
dpwAtmPerfCurrentCellsXmit Number of transmitted cells.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.5
dpwAtmPerfCurrentCellsDropped Number of dropped cells.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.6
dpwAtmPerfCurrentCellsReceived Number of received cells.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.7
dpwAtmPerfCurrentUnknownCells Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.7.1.8

This table provides performance information per ATM PW
similar to the pwAtmPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period.

dpwAtmPerfIntervalEntry row .0.1.1.8.1

An entry in this table is created by the agent for
every pwAtmPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zer…

Indexes

PW-STD-MIBpwIndex dpwAtmPerfIntervalNumber

Column	Syntax	OID
dpwAtmPerfIntervalNumber A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, …	Unsigned32 Constraints: range: 1-96	.0.1.1.8.1.1
dpwAtmPerfIntervalValidData This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.1.1.8.1.2
dpwAtmPerfIntervalDuration The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.0.1.1.8.1.3
dpwAtmPerfIntervalMissingPkts Number of missing packets (as detected via control word sequence number gaps).	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.4
dpwAtmPerfIntervalPktsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.5
dpwAtmPerfIntervalPktsMisOrder Number of packets detected out of order (via control word sequence numbers).	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.6
dpwAtmPerfIntervalPktsTimeout Number of packets transmitted due to timeout expiration.	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.7
dpwAtmPerfIntervalCellsXmit Number of transmitted cells.	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.8
dpwAtmPerfIntervalCellsDropped Number of dropped cells.	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.9
dpwAtmPerfIntervalCellsReceived Number of received cells.	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.10
dpwAtmPerfIntervalUnknownCells Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.	PerfHist-TC-MIBPerfIntervalCount	.0.1.1.8.1.11
dpwAtmPerfIntervalTime Timestamp value of the system in hours, minutes and seconds when data is received for particular pseudo-wire for every 15-minutes	OctetString	.0.1.1.8.1.12

This table provides performance information per ATM PW
similar to the pwAtmPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month.

dpwAtmPerf1DayIntervalEntry row .0.1.1.9.1

An entry is created in this table by the agent
for every entry in the pwAtmCfgTable table.

Indexes

PW-STD-MIBpwIndex dpwAtmPerf1DayIntervalNumber

Column	Syntax	OID
dpwAtmPerf1DayIntervalNumber The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively	Unsigned32 Constraints: range: 1-365	.0.1.1.9.1.1
dpwAtmPerf1DayIntervalValidData This object indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.0.1.1.9.1.2
dpwAtmPerf1DayIntervalDuration The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.3
dpwAtmPerf1DayIntervalMissingPkts Number of missing packets (as detected via control word sequence number gaps).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.4
dpwAtmPerf1DayIntervalPktsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.5
dpwAtmPerf1DayIntervalPktsMisOrder Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.6
dpwAtmPerf1DayIntervalPktsTimeout Number of packets transmitted due to timeout expiration.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.7
dpwAtmPerf1DayIntervalCellsXmit Number of transmitted cells.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.8
dpwAtmPerf1DayIntervalCellsDropped Number of dropped cells.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.9
dpwAtmPerf1DayIntervalCellsReceived Number of received cells.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.10
dpwAtmPerf1DayIntervalUnknownCells Number of cells received from the PSN with unknown VPI or VCI value. This object is relevant only in N:1 mode.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.0.1.1.9.1.11
dpwAtmPerf1DayIntervalTime Timestamp value of the system in hours, minutes and seconds when data is received for particular pseudo-wire for every day	OctetString	.0.1.1.9.1.12

This table specifies to enable/disable OAM 
on the PW associated to the specified pwIndex.
It also shows the defects of the PW OAM.

dpwOamEntry row .0.1.1.10.1

This table is indexed by pwIndex.
Unless otherwise specified, all read-create
objects in this table MUST NOT be changed
after row activation and SHOULD remain
unchanged after reboot.

Indexes

PW-STD-MIBpwIndex

Column	Syntax	OID
dpwOamEnable This variable indicates if OAM is enabled for this PW. It MAY be changed at any time.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.1.1.10.1.1
dpwOamDefect This specifies the defect states of PW OAM	Integer32 Type Constraints: range: -2147483648..2147483647	.0.1.1.10.1.2
dpwOamRowStatus For creating, modifying, and deleting this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.0.1.1.10.1.3

This table specifies to enable/disable CC Generation and also
to set the Flow Type as E2E / SEG.

dpwAtmoamEntry row .0.1.1.11.1

This table is indexed by pwIndex.
Unless otherwise specified, all read-create
objects in this table MUST NOT be changed
after row activation and SHOULD remain
unchanged after reboot.

Indexes

PW-STD-MIBpwIndex

Column	Syntax	OID
dpwCcStatus This variable is used to enable / disable the CC Status.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.1.1.11.1.1
dpwFlowType This variable is used to set the flow type as E2E / SEG / Both.	Enumerationr/w Enumerated Values: 1 ete 2 seg 3 both	.0.1.1.11.1.2
dpwAtmoamRowStatus For creating, modifying, and deleting this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.0.1.1.11.1.3
dpwFrequencyTimerIntvl This variable is used to set the Frequency Timer Interval. The frequency timer interval can be 1 or 2	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.0.1.1.11.1.4

This table contains VP Shaping related parameters for upstream ont qos.

dpwAtmVpShapingEntry row .0.1.1.12.1

An entry in this table is created for upstream ont qos vci-qos.

Indexes

dpwAtmOntid dpwAtmVpi

Column	Syntax	OID
dpwAtmVpShapingBandwidth The Vp shaping bandwidth for upstream ATM cell packets. The unit of bandwidth is in cell/seconds.	Unsigned32r/w Constraints: range: 300-358795	.0.1.1.12.1.1
dpwAtmVpShapingRowStatus This Object is used to create, modify and delete a row in this table. When the Row status is active, whenever user configures in OLT, ONT is also configured. For row creation, user is suggested to configure the bandwidt…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1.1.12.1.2

The OAM statistic counts are in
this table.
This table provides OAM statistics information per ATM PW.

dpwAtmOamStatsEntry row .0.1.1.13.1

An entry in this table is created when AIS/RDI cells are received.
Number of OAM cells Txmitted and received are incremented

Indexes

PW-STD-MIBpwIndex

Column	Syntax	OID
dpwAtmOamStatsOamCellsRx Number of OAM Cells received.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.13.1.1
dpwAtmOamStatsOamCellsTx Number of OAM Cells transmitted.	PerfHist-TC-MIBPerfCurrentCount	.0.1.1.13.1.2