DC-LMP-PROD Table View

The index of this dcLmpProductEntry. This is the
HAF entity index passed on the entity create parameters.

The Node ID for this LMP node.

Management assigned interface identifier for the IP Sockets
component interface to DC-LMP.

The number of buffers available for sending
sockets data to a given neighbor. This is used to pace
the sockets data flow. There can never be more than this
many outstanding unacked non-IPCC messages to a given neighbo…

The number of pre-reserved buffers available for interacting
with the DLM provider. This is used to ensure DLM
interactions do not fail in buffer shortage conditions.

Note that this field may not be alte…

The initial interval in milliseconds between resends of LMP
messages, where per-message type values are not provided.

The default factor that governs the speed with which the
sender increases the retransmission interval.

This object specifies the default value for the HelloInterval
parameter used in the Hello protocol keep-alive phase. It
indicates how frequently LMP Hello messages will be sent.

This field is used as the …

This object specifies the default minimum value for the
HelloInterval parameter. It is used as a default value
for lmpCcHelloIntervalMin.

This field can be set to zero to disable the LMP Hello
mechanism.

This object specifies the default maximum value for the
HelloInterval parameter. It is used as a default value
for lmpCcHelloIntervalMax.

This field can be set to zero to disable the LMP Hello
mechanism.

This object specifies the default HelloDeadInterval parameter to
use in the Hello protocol keep-alive phase. It indicates how long
a device should wait before declaring the control channel dead.

The Hello…

This object specifies the default minimum value for the
HelloDeadInterval parameter. It is used as a default value
for lmpCcHelloDeadIntervalMin.

This field can be set to zero to disable the LMP Hello
mec…

This object specifies the default maximum value for the
HelloDeadInterval parameter. It is used as a default value
for lmpCcHelloDeadIntervalMax.

This field can be set to zero to disable the LMP Hello
mec…

This object indicates how often the link verification
procedure is executed.

This field can be set to zero to disable periodic link
verification.

If this object is true, then it enables the
generation of lmpTeLinkPropertyMismatch
and lmpDataLinkPropertyMismatch notifications,
otherwise these notifications are not emitted.

If this object is true, then it enables the
generation of lmpUnprotected notification,
otherwise these notifications are not emitted.

If this object is true, then it enables the generation of
lmpControlChannelUp and lmpControlChannelDown notifications,
otherwise these notifications are not emitted.

If this object is true, then it enables the
generation of lmpTeLinkDegraded and lmpTeLinkNotDegraded
notifications, otherwise these notifications are not emitted.

If this object is true, then it enables the
generation of lmpTeLinkCorrelated notification,
otherwise these notifications are not emitted.

If this object is true, then it enables the
generation of lmpDataLinkVerificationFailure notifications,
otherwise these notifications are not emitted.

Denotes whether or not this instance of DC-LMP should
automatically generate new entries in the neighbor table
for new neighbors discovered during control channel
setup. This feature only applies to control channels
th…

Denotes whether or not this instance of DC-LMP should
attempt to automatically correlate TE links with neighbor
nodes.

When this feature is enabled, then during link
correlation DC-LMP will attempt to per…

The interval in milliseconds between schedulings of UNI Service
Discovery. If 0, UNI is not scheduled repeatedly.

The maximum allowed time in milliseconds of a UNI Service Discovery
exchange.

OIF UNI specifies that Config, ConfigAck, ConfigNack and Hello
messages be sent to the neighbor's IPCC address (or the All-nodes
multicast address in the case of an in-fibre Config).
All other messages must be sent with…

Flag to indicate whether DC-LMP has restarted following a
failure. If this is true, then for a period
_LMP_PRODUCT_RESTART_TIME_ after restarting, LinkSummary
messages are processed differently, according to the
sectio…

The desired administrative state of the LMP entity.

The current operational state of the LMP entity.

Used to create and delete an LMP Product Table entry.
Note that when this object is set to 'active', the
dcLmpProductSocketBufPoolSize and dcLmpProductDLMIBufPoolSize
objects in the row may not be modified.

This field is now deprecated. WDM is now configured on a per TE Link
and Control Channel basis. The lmpTeLinkDwdm and lmpCcWdmMode fields
should be used instead.

Indicates whether this LMP entity can operate in an WDM role and if
so whether it should take the role of a peer or optical line system
(OLS).

Some LMP implementations use the Node ID as the source IP address in
LMP messages.

In UNI scenarios this is safe, because the Node ID is drawn from the
same address space as the interface addresses, and s…

When set to a non-zero value greater than
lmpCcHelloDeadIntervalNegotiated, the object overrides the
value of lmpCcHelloDeadIntervalNegotiated for a control
channel to indicate how long the device…

The if_index of test port for LMP correlation procedure.
The test port used as LMP TEST signal injection origin.

The wavelength of test signal for LMP correlation procedure.

This object specifies the VerifyDeadInterval parameter
used in the verification of the physical connectivity of
data-bearing links. It specifies the observation period
used to detect a Test message at the remote node.

The default attenuation level for GMPLS tunnels when programming ROADM channel map
for the case when EDFA amplifier is used at the common ROADM port.

The default attenuation level for GMPLS tunnels when programming ROADM channel map
for the case when EDFA amplifier isn't used at the common ROADM port.