CISCOSB-rlInterfaces Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
6
Rows
6
Columns
68

swIfTable

table
.1.3.6.1.4.1.9.6.1.101.43.1 · 1 row entry · 50 columns
Open in standard view 
Switch media specific information and configuration of the device
interfaces.
swIfEntry entry .1.3.6.1.4.1.9.6.1.101.43.1.1
Defines the contents of each line in the swIfTable table.
Indexes
swIfIndex
Column Syntax OID
swIfIndex
Index to the swIfTable. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II).
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.1
swIfPhysAddressType obsolete
This variable indicates whether the physical address assigned to this
interface should be the default one or be chosen from the set of
reserved physical addresses of the device.
Enumerationr/w
Enumerated Values:
1default
2reserve
 .1.3.6.1.4.1.9.6.1.101.43.1.1.2
swIfDuplexAdminMode
This variable specifies whether this interface should operate in
half duplex or full duplex mode. This specification will take effect
only if swIfSpeedDuplexAutoNegotiation is disabled.
A value of 'none' is returned if …
Enumerationr/w
Enumerated Values:
1none
2half
3full
 .1.3.6.1.4.1.9.6.1.101.43.1.1.3
swIfDuplexOperMode
This variable indicates whether this interface operates in half
duplex or full duplex mode.
This variable can have the values hybrid or unknown
only for a trunk.
unknown - only if trunk operative status is not present.
Enumeration
Enumerated Values:
1half
2full
3hybrid
4unknown
 .1.3.6.1.4.1.9.6.1.101.43.1.1.4
swIfBackPressureMode
This variable indicates whether this interface activates back pressure
when congested.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.9.6.1.101.43.1.1.5
swIfTaggedMode
If enable, this interface operates in tagged mode, i.e all frames sent
out through this interface will have the 802.1Q header.
If disabled the frames will not be tagged.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.9.6.1.101.43.1.1.6
swIfTransceiverType
This variable indicates the transceiver type of this interface.
Enumeration
Enumerated Values:
1regular
2fiberOptics
3comboRegular
4comboFiberOptics
 .1.3.6.1.4.1.9.6.1.101.43.1.1.7
swIfLockAdminStatus
This variable indicates whether this interface should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from this port and
forwards all frames arrived at this port. In locked mode …
Enumerationr/w
Enumerated Values:
1locked
2unlocked
 .1.3.6.1.4.1.9.6.1.101.43.1.1.8
swIfLockOperStatus
This variable defines whether this interface operates in locked
or unlocked mode. It is locked in each of the following two cases:
1) if swLockAdminStatus is set to locked
2) no IP/IPX interface is defined over…
Enumeration
Enumerated Values:
1locked
2unlocked
 .1.3.6.1.4.1.9.6.1.101.43.1.1.9
swIfType
This variable specifies the type of interface.
Enumeration
Enumerated Values:
1eth10M
2eth100M
3eth1000M
4eth2500M
5eth5G
6eth10G
7eth20G
8eth40G
9eth100G
10eth25G
11eth50G
12unknown
 .1.3.6.1.4.1.9.6.1.101.43.1.1.10
swIfDefaultTag
This variable specifies the default VLAN tag which will be attached
to outgoing frames if swIfTaggedMode for this interface is enabled.
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.6.1.101.43.1.1.11
swIfDefaultPriority
This variable specifies the default port priority.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.9.6.1.101.43.1.1.12
swIfStatus
The status of a table entry.
It is used to delete an entry from this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.6.1.101.43.1.1.13
swIfFlowControlMode
on - Flow control will be enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
autoNegotiation - Flow control will be enabled or disabled on this
interface. If en…
Enumerationr/w
Enumerated Values:
1on
2off
3autoNegotiation
4enabledRx
5enabledTx
 .1.3.6.1.4.1.9.6.1.101.43.1.1.14
swIfSpeedAdminMode
This variable specifies the required speed of this interface in bits
per second. This specification will take effect only if
swIfSpeedDuplexAutoNegotiation is disabled.
A value of 10 is returned for 10G.
A value of 0 is…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.15
swIfSpeedDuplexAutoNegotiation
If enabled the speed and duplex mode will be set by the device through
the autonegotiation process. Otherwise these characteristics will be
set according to the values of swIfSpeedAdminMode and
swIfSpeedDuplexAutoNegoti…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.9.6.1.101.43.1.1.16
swIfOperFlowControlMode
on - Flow control is enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
enabledRx - Flow control is enabled on this interface for
recieved frames.
enabledTx - Flow co…
Enumeration
Enumerated Values:
1on
2off
3enabledRx
4enabledTx
 .1.3.6.1.4.1.9.6.1.101.43.1.1.17
swIfOperSpeedDuplexAutoNegotiation
If enabled the speed and duplex are determined by the device through
the autonegotiation process.
If disabled these characteristics are determined according to the values
of swIfSpeedAdminMode and swIfDuplexAdminMode.
h…
Enumeration
Enumerated Values:
1enabled
2disabled
3hybrid
4unknown
 .1.3.6.1.4.1.9.6.1.101.43.1.1.18
swIfOperBackPressureMode
This variable indicates the operative back pressure mode of
this interface.
Enumeration
Enumerated Values:
1enable
2disable
3hybrid
4unknown
 .1.3.6.1.4.1.9.6.1.101.43.1.1.19
swIfAdminLockAction
This variable indicates which action this interface should be taken
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is f…
Enumerationr/w
Enumerated Values:
1discard
2forwardNormal
3discardDisable
 .1.3.6.1.4.1.9.6.1.101.43.1.1.20
swIfOperLockAction
This variable indicates which action this interface actually takes in
locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is fo…
Enumeration
Enumerated Values:
1discard
2forwardNormal
3discardDisable
 .1.3.6.1.4.1.9.6.1.101.43.1.1.21
swIfAdminLockTrapEnable
This variable indicates whether to create a SNMP trap in the locked mode.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.1.1.22
swIfOperLockTrapEnable
This variable indicates whether a SNMP trap can be created in the
locked mode.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.1.1.23
swIfOperSuspendedStatus
This variable indicates whether the port is suspended or not due to some
feature. After reboot this value is false
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.1.1.24
swIfLockOperTrapCount
This variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a
packet which was received on this ifIndex). It's relevant only in locked
mode while trap is …
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.25
swIfLockAdminTrapFrequency
This variable indicates the minimal frequency (in seconds) of sending
a trap per ifIndex. It's relevant only in locked mode and in trap
enabled.
Integer32r/w
Constraints:
range: 1-1000000
 .1.3.6.1.4.1.9.6.1.101.43.1.1.26
swIfReActivate
This variable reactivates (enables) an ifIndex (which was suspended)
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.1.1.27
swIfAdminMdix
The configuration is on a physical port, not include trunks.
cross - The interface should force crossover.
normal - The interface should not force crossover.
auto - Auto mdix is enabled on the interface.
Enumerationr/w
Enumerated Values:
1cross
2normal
3auto
 .1.3.6.1.4.1.9.6.1.101.43.1.1.28
swIfOperMdix
cross - The interface is in crossover mode.
normal - The interface is not in crossover mode.
unknown - Only for port that its operative status is not present
or down.
Enumeration
Enumerated Values:
1cross
2normal
3unknown
 .1.3.6.1.4.1.9.6.1.101.43.1.1.29
swIfHostMode
This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto.
In addtion multiple-auth was added.
Enumerationr/w
Enumerated Values:
1single
2multiple
3multiple-auth
 .1.3.6.1.4.1.9.6.1.101.43.1.1.30
swIfSingleHostViolationAdminAction
This variable indicates which action this interface should take in single authorized.
Possible actions:
discard - every packet is dropped.
forwardNormal - every packet is forwarded according to the DST address.
discardD…
Enumerationr/w
Enumerated Values:
1discard
2forwardNormal
3discardDisable
 .1.3.6.1.4.1.9.6.1.101.43.1.1.31
swIfSingleHostViolationOperAction
This variable indicates which action this interface actually takes in single authorized.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is forwarded according to the DST address.…
Enumeration
Enumerated Values:
1discard
2forwardNormal
3discardDisable
 .1.3.6.1.4.1.9.6.1.101.43.1.1.32
swIfSingleHostViolationAdminTrapEnable
This variable indicates whether to create a SNMP trap in single authorized.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.1.1.33
swIfSingleHostViolationOperTrapEnable
This variable indicates whether a SNMP trap can be created in the single authorized.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.1.1.34
swIfSingleHostViolationOperTrapCount
This variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a packet
which was received on this ifIndex). It's relevant only in single authorized
while tr…
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.35
swIfSingleHostViolationAdminTrapFrequency
This variable indicates the minimal frequency (in seconds) of sending a
trap per ifIndex. It's relevant only in single authorized and in trap enabled.
A value of 0 means that trap is disabled.
Integer32r/w
Constraints:
range: 0-1000000
 .1.3.6.1.4.1.9.6.1.101.43.1.1.36
swIfLockLimitationMode
This variable indicates what is the learning limitation on the locked interface.
Possible values:
disabled - learning is stopped. The dynamic addresses associated with the
port are not aged out or relearned on other…
Enumerationr/w
Enumerated Values:
1disabled
2dynamic
3secure-permanent
4secure-delete-on-reset
 .1.3.6.1.4.1.9.6.1.101.43.1.1.37
swIfLockMaxMacAddresses
This variable defines the maximum number of dynamic addresses that
can be asscoiated with the locked interface. It isn't relevant in
disabled limitation mode.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.38
swIfLockMacAddressesCount
This variable indicates the actual number of dynamic addresses that can
be asscoiated with the locked interface. It isn't relevant in disabled
limitation mode.
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.39
swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities
Administrative auto negotiation capabilities of the interface that can be advertised when
swIfSpeedDuplexAutoNegotiation is enabled.
default bit means advertise all the port's capabilities
according to its type.
AutoNegCapabilitiesBitsr/w
Textual Convention: AutoNegCapabilitiesBits Bits
Type Values:
0default
1unknown
2tenHalf
3tenFull
4fastHalf
5fastFull
6gigaHalf
7gigaFull
8tenGigaFull
9fiveGigaFull
10twoPointFiveGigaFull
11twentyFiveGigaFull
12fortyGigaFull
13fiftyGigaFull
14oneHundredGigaFull
15twoHundredGigaFull
 .1.3.6.1.4.1.9.6.1.101.43.1.1.40
swIfOperSpeedDuplexAutoNegotiationLocalCapabilities
Operative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up.
AutoNegCapabilitiesBits
Textual Convention: AutoNegCapabilitiesBits Bits
Type Values:
0default
1unknown
2tenHalf
3tenFull
4fastHalf
5fastFull
6gigaHalf
7gigaFull
8tenGigaFull
9fiveGigaFull
10twoPointFiveGigaFull
11twentyFiveGigaFull
12fortyGigaFull
13fiftyGigaFull
14oneHundredGigaFull
15twoHundredGigaFull
 .1.3.6.1.4.1.9.6.1.101.43.1.1.41
swIfSpeedDuplexNegotiationRemoteCapabilities
Operative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up,
or auto negotiation process not complete,
or remote link is not auto negotiation able.
AutoNegCapabilitiesBits
Textual Convention: AutoNegCapabilitiesBits Bits
Type Values:
0default
1unknown
2tenHalf
3tenFull
4fastHalf
5fastFull
6gigaHalf
7gigaFull
8tenGigaFull
9fiveGigaFull
10twoPointFiveGigaFull
11twentyFiveGigaFull
12fortyGigaFull
13fiftyGigaFull
14oneHundredGigaFull
15twoHundredGigaFull
 .1.3.6.1.4.1.9.6.1.101.43.1.1.42
swIfAdminComboMode
This variable specifies the administrative mode of a combo Ethernet interface.
Enumerationr/w
Enumerated Values:
1force-fiber
2force-copper
3prefer-fiber
4prefer-copper
 .1.3.6.1.4.1.9.6.1.101.43.1.1.43
swIfOperComboMode
This variable specifies the operative mode of a combo Ethernet interface.
Enumeration
Enumerated Values:
1fiber
2copper
3unknown
 .1.3.6.1.4.1.9.6.1.101.43.1.1.44
swIfAutoNegotiationMasterSlavePreference
This variable specifies the administrative mode of the Maste-Slave preference in auto negotiation.
Enumerationr/w
Enumerated Values:
1preferMaster
2preferSlave
 .1.3.6.1.4.1.9.6.1.101.43.1.1.45
swIfPortCapabilities
Returns the port capabilities.
AutoNegCapabilitiesBits
Textual Convention: AutoNegCapabilitiesBits Bits
Type Values:
0default
1unknown
2tenHalf
3tenFull
4fastHalf
5fastFull
6gigaHalf
7gigaFull
8tenGigaFull
9fiveGigaFull
10twoPointFiveGigaFull
11twentyFiveGigaFull
12fortyGigaFull
13fiftyGigaFull
14oneHundredGigaFull
15twoHundredGigaFull
 .1.3.6.1.4.1.9.6.1.101.43.1.1.46
swIfPortStateDuration
The amount of time(in sec) that a port has been up or down.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.43.1.1.47
swIfApNegotiationLane
which lane is used to perform negotiation in AP mode.
Enumerationr/w
Enumerated Values:
0laneZero
1laneOne
2laneTwo
3laneThree
 .1.3.6.1.4.1.9.6.1.101.43.1.1.48
swIfPortFecMode
determine fec (error correction) mode.
Enumerationr/w
Enumerated Values:
1fc
2rs
3none
128default
 .1.3.6.1.4.1.9.6.1.101.43.1.1.49
swIfPortNumOfLanes
determine number of lanes to configure interface mode.
Enumerationr/w
Enumerated Values:
1oneLane
2twoLanes
4fourLanes
8eightLanes
128default
 .1.3.6.1.4.1.9.6.1.101.43.1.1.50

swIfPortLockIfRangeTable

table
.1.3.6.1.4.1.9.6.1.101.43.6 · 1 row entry · 6 columns
Open in standard view 
Port lock interfaces range configuration
swIfPortLockIfRangeEntry entry .1.3.6.1.4.1.9.6.1.101.43.6.1
Defines the contents of each line in the swIfPortLockIfRangeTable table.
Indexes
swIfPortLockIfRangeIndex
Column Syntax OID
swIfPortLockIfRangeIndex
Index to the swIfPortLockIfRangeTable.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.43.6.1.1
swIfPortLockIfRange
The set of interfaces to which the port lock parameters should be configured
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
 .1.3.6.1.4.1.9.6.1.101.43.6.1.2
swIfPortLockIfRangeLockStatus
This variable indicates whether the interfaces range should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from these interfaces and
forwards all frames arrived at these interfa…
Enumerationr/w
Enumerated Values:
1locked
2unlocked
 .1.3.6.1.4.1.9.6.1.101.43.6.1.3
swIfPortLockIfRangeAction
This variable indicates which action for these interfaces should be take
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet…
Enumerationr/w
Enumerated Values:
1discard
2forwardNormal
3discardDisable
 .1.3.6.1.4.1.9.6.1.101.43.6.1.4
swIfPortLockIfRangeTrapEn
This variable indicates whether to create a SNMP trap in the locked mode.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.43.6.1.5
swIfPortLockIfRangeTrapFreq
This variable indicates the minimal frequency (in seconds) of sending
a trap for these interfaces. It's relevant only in locked mode and in trap
enabled.
Integer32r/w
Constraints:
range: 1-1000000
 .1.3.6.1.4.1.9.6.1.101.43.6.1.6

swIfExtTable

table
.1.3.6.1.4.1.9.6.1.101.43.7 · 1 row entry · 1 columns
Open in standard view 
Display information and configuration of the device interfaces.
swIfExtEntry entry .1.3.6.1.4.1.9.6.1.101.43.7.1
Defines the contents of each row in the swIfExtTable.
Indexes
IF-MIBifIndex
Column Syntax OID
swIfExtSFPSpeed
Configure speed of an SFP Ethernet interface.
Enumerationr/w
Enumerated Values:
1default
2eth100M
3eth1G
 .1.3.6.1.4.1.9.6.1.101.43.7.1.1

rlMacOperationTable

table
.1.3.6.1.4.1.9.6.1.101.43.8 · 1 row entry · 2 columns
Open in standard view 
pefrom mac operation on given ifindex
macOperationEntry entry .1.3.6.1.4.1.9.6.1.101.43.8.1
Defines mac operation
Indexes
macOpifIndex
Column Syntax OID
macOpifIndex
Index to the rlMacOperationTable. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II).
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.43.8.1.1
macOpType
This variable indicates what operation should be performed on the MAC
of the given interface.
Enumerationr/w
Enumerated Values:
1securePortDynamicToStatic
2securePortClearStatic
 .1.3.6.1.4.1.9.6.1.101.43.8.1.2

rlIfCutThroughTable

table
.1.3.6.1.4.1.9.6.1.101.54.27 · 1 row entry · 3 columns
Open in standard view 
Information and configuration of cut-through feature.
rlIfCutThroughEntry entry .1.3.6.1.4.1.9.6.1.101.54.27.1
Defines the contents of each line in the swIfTable table.
Indexes
swIfIndex
Column Syntax OID
rlIfCutThroughPriorityEnable
Enable or disable cut-through for a priority for an interface.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.54.27.1.1
rlIfCutThroughUntaggedEnable
Enable or disable cut-through for untagged packets for an interface.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.54.27.1.2
rlIfCutThroughOperMode
Operational mode of spesific cut-through interface.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.54.27.1.3

rlIfApPortTable

table
.1.3.6.1.4.1.9.6.1.101.54.35 · 1 row entry · 6 columns
Open in standard view 
Information and configuration of AP advertisements feature.
rlIfApPortEntry entry .1.3.6.1.4.1.9.6.1.101.54.35.1
Defines the contents of each line in the rlIfApPortTable table.
Indexes
rlIfApPortIndex rlIfApPortSpeed
Column Syntax OID
rlIfApPortIndex
Index to the swIfApTable. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II).
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.54.35.1.1
rlIfApPortSpeed
This variable specifies the required speed of this interface in bits
per second. This specification will take effect only if
swIfSpeedDuplexAutoNegotiation is disabled.
A value of 10 is returned for 10G.
A value of 0 is…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.54.35.1.2
rlIfApPortFcFecSupported
Enable or disable support FC fec on an interface.
Enumerationr/w
Enumerated Values:
0default
1true
2false
 .1.3.6.1.4.1.9.6.1.101.54.35.1.3
rlIfApPortRsFecSupported
Enable or disable support RS fec on an interface.
Enumerationr/w
Enumerated Values:
0default
1true
2false
 .1.3.6.1.4.1.9.6.1.101.54.35.1.4
rlIfApPortFecRequired
Required or not required fec from link partner.
Enumerationr/w
Enumerated Values:
0default
1true
2false
 .1.3.6.1.4.1.9.6.1.101.54.35.1.5
rlIfApPortNumOfLanesBmp
num of lanes to advertize per speed for interface mode.
NumOfLanesBitsr/w
Textual Convention: NumOfLanesBits Bits
Type Values:
0default
1oneLane
2twoLanes
3fourLanes
4eightLanes
 .1.3.6.1.4.1.9.6.1.101.54.35.1.6