CISCOSB-IPv6 Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
16
Rows
16
Columns
108

rlIpAddressTable

table
.1.3.6.1.4.1.9.6.1.101.26.19 · 1 row entry · 2 columns
Open in standard view 
This table is parallel to ipAddressTable, and is used to
add/delete IPv6 entries to/from that table. It contains
private objects.
rlIpAddressEntry entry .1.3.6.1.4.1.9.6.1.101.26.19.1
An address mapping for a particular interface.
Indexes
No indexes recorded
Column Syntax OID
rlIpAddressPrefixLength
The prefix length of this address.
INET-ADDRESS-MIBInetAddressPrefixLengthr/w
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.26.19.1.1
rlIpAddressType
Extend standard field ipAddressType to multicast
Enumeration .1.3.6.1.4.1.9.6.1.101.26.19.1.2

rlipv6InterfaceTable

table
.1.3.6.1.4.1.9.6.1.101.26.20 · 1 row entry · 7 columns
Open in standard view 
This table is parallel to ipv6InterfaceTable, and is used to
configure additional interface parameters.
rlipv6InterfaceEntry entry .1.3.6.1.4.1.9.6.1.101.26.20.1
Additional configuration parameters for a particular interface.
Indexes
No indexes recorded
Column Syntax OID
rlipv6InterfaceNdDadAttemps
ND Duplicated address detection number of attempts.
Integer32r/w
Constraints:
range: 0-600
 .1.3.6.1.4.1.9.6.1.101.26.20.1.1
rlipv6InterfaceAutoconfigEnable
Enables or disables Stateless Address Auto configuration
on specific interface.
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.26.20.1.2
rlipv6InterfaceIcmpUnreachSendEnable
Enables or disables sending of ICMP Destination Unreachable
Error on specific interface.
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.26.20.1.3
rlipv6InterfaceLinkMTU
The maximum transmission unit (MTU) size of IPv6 packets
sent on an interface in bytes.
Unsigned32r/w
Constraints:
range: 1280-65535
 .1.3.6.1.4.1.9.6.1.101.26.20.1.4
rlipv6InterfaceMLDVersion
Set version of MLD protocol on specific interface.
Unsigned32r/w
Constraints:
range: 1-2
 .1.3.6.1.4.1.9.6.1.101.26.20.1.5
rlipv6InterfaceRetransmitTime
This value will be included in all IPv6 router advertisements sent
out this interface. Very short intervals are not recommended in
normal IPv6 operation. When a nondefault value is configured, the
configured time is bot…
millisecondsUnsigned32r/w
Enumerated Values:
1enable
2disable
Constraints:
range: 0-0
range: 1000-3600000
 .1.3.6.1.4.1.9.6.1.101.26.20.1.6
rlipv6InterfaceIcmpRedirectSendEnable
Enables or disables sending of ICMP IPv6 redirect messages to
re-send a packet through the same interface on which the packet was
received.
Enumerationr/w
Enumerated Values:
1enable
2disable
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.6.1.101.26.20.1.7

rlinetCidrRouteTable

table
.1.3.6.1.4.1.9.6.1.101.26.21 · 1 row entry · 2 columns
Open in standard view 
This table is parallel to inetCidrRouteTable, and is used to
configure or display additional route parameters.
rlinetCidrRouteEntry entry .1.3.6.1.4.1.9.6.1.101.26.21.1
Additional parameters for a particular route.
Indexes
No indexes recorded
Column Syntax OID
rlinetCidrRouteLifetime
The remaining length of time, in seconds, that this route
will continue to be valid, i.e., time until deprecation.
A value of 4,294,967,295 represents infinity.
secondsSNMPv2-SMIUnsigned32
Enumerated Values:
1unconfigured
2image1
3image2
Constraints:
range: 1-2
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.21.1.1
rlinetCidrRouteInfo
A reference to MIB definitions specific to the particular routing
protocol which is responsible for this route, as determined by the
value specified in the route's inetCidrRouteProto value.
Enumeration
Enumerated Values:
1enable
2disable
Constraints:
range: 1-5
 .1.3.6.1.4.1.9.6.1.101.26.21.1.2

rlipNetToPhysicalTable

table
.1.3.6.1.4.1.9.6.1.101.26.22 · 1 row entry · 2 columns
Open in standard view 
This table is parallel to ipNetToPhysicalTable, and is used to
configure or display additional neighbor parameters.
rlipNetToPhysicalEntry entry .1.3.6.1.4.1.9.6.1.101.26.22.1
Additional parameters for a neighbor
Indexes
No indexes recorded
Column Syntax OID
rlipNetToPhysicalIsRouter
This object has the value 'true(1)', if the neighbor
is router; otherwise, the value is 'false(2)'.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.26.22.1.1
rlipNetToPhysicalReachableConfirmed
Time (in seconds) since the address was confirmed to be reachable.
Only, relevant for dynamic entries.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.22.1.2

rlInetStaticRouteTable

table
.1.3.6.1.4.1.9.6.1.101.26.28 · 1 row entry · 13 columns
Open in standard view 
This entity's static (user configured) Inet Routing table.
Entries are MAX-ACCESSible even if not used for forwarding
rlInetStaticRouteEntry entry .1.3.6.1.4.1.9.6.1.101.26.28.1
A particular Static(user configured) route to a particular destination.
Indexes
rlInetStaticRouteDestType rlInetStaticRouteDest rlInetStaticRoutePfxLen rlInetStaticRouteNextHopType rlInetStaticRouteNextHop rlInetStaticRouteIfIndex
Column Syntax OID
rlInetStaticRouteDestType
The type of the address used as the destination
internetwork address or subnet address.
INET-ADDRESS-MIBInetAddressType
Constraints:
range: 0-80
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.26.28.1.1
rlInetStaticRouteDest
Destination internetwork address or subnet address. The
destination prefix length is applied to this value, and to a
particular destination address, to determine whether the route
applies to the particular address.
If …
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.26.28.1.2
rlInetStaticRoutePfxLen
Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlInetStaticRouteDest field.
INET-ADDRESS-MIBInetAddressPrefixLength
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.26.28.1.3
rlInetStaticRouteNextHopType
The type of the address used as the next-hop address
for this route.
INET-ADDRESS-MIBInetAddressType
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.26.28.1.4
rlInetStaticRouteNextHop
The next-hop IP address, if any.
If rlInetStaticRouteAction is 'forward', there may or may not be
a next-hop IP address.
A next-hop IP address is not required if an output interface
index is specified (in other words, i…
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.26.28.1.5
rlInetStaticRouteIfIndex
The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified.
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.28.1.6
rlInetStaticRoutePathCost
Path cost for this static route.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.28.1.7
rlInetStaticRouteType
Same as inetCidrRouteType MIB (excluded 'other' route type)
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.26.28.1.8
rlInetStaticRouteOwner
Static - The route is configured over Static IP.
This route is written to configuration files.
Dhcp - The route is Configured by DHCP
(received as part of DHCP configuration)
This route IS NOT written to configurati…
Enumeration
Enumerated Values:
1mgmtUnit
2stackUnit
3mgmtUnassigned
 .1.3.6.1.4.1.9.6.1.101.26.28.1.9
rlInetStaticRouteRowStatus
The row status variable, used according to row
installation and removal conventions.
A row entry cannot be modified when the status is
marked as active(1).
SNMPv2-TCRowStatusr/w
Constraints:
range: 0-255
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.6.1.101.26.28.1.10
rlInetStaticRouteForwardingStatus
active - An indication that the route has implication on routing
inactive - the route is a backup route or it is down. It is not used
in forwarding decision.
Down means that the Ip interface on which it is co…
Enumeration
Constraints:
range: 0-15
 .1.3.6.1.4.1.9.6.1.101.26.28.1.11
rlInetStaticRouteTrackObject
Track object number
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.28.1.12
rlInetStaticRouteTrackStatus
Track status
Enumeration
Constraints:
range: 0-15
 .1.3.6.1.4.1.9.6.1.101.26.28.1.13

rlInetRoutingDistanceTable

table
.1.3.6.1.4.1.9.6.1.101.26.29 · 1 row entry · 6 columns
Open in standard view 
This table defines administrative distances for
different protocol routes that are inserted into
the routing table.
rlInetRoutingDistanceEntry entry .1.3.6.1.4.1.9.6.1.101.26.29.1
A set of distances per inet address type.
Indexes
rlInetRoutingDistanceType
Column Syntax OID
rlInetRoutingDistanceType
The inet address type for distance definitions set,
either IPv4 or IPv6.
Enumeration
Constraints:
range: 1-255
 .1.3.6.1.4.1.9.6.1.101.26.29.1.1
rlInetRoutingDistanceConnected
The administrative distance used for directly connected routes.
Integer32r/w
Constraints:
range: 0-255
range: 0-255
 .1.3.6.1.4.1.9.6.1.101.26.29.1.2
rlInetRoutingDistanceStatic
The administrative distance used for static routes.
Integer32r/w
Constraints:
range: 0-80
range: 0-255
 .1.3.6.1.4.1.9.6.1.101.26.29.1.3
rlInetRoutingDistanceRip
The administrative distance used for RIP routes.
Integer32r/w
Enumerated Values:
1enable
2disable
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.6.1.101.26.29.1.4
rlInetRoutingDistanceOspfInternal
The administrative distance used for OSPF internal routes.
Integer32r/w
Enumerated Values:
1enable
2disable
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.6.1.101.26.29.1.5
rlInetRoutingDistanceOspfExternal
The administrative distance used for OSPF Autonomous System external routes.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.6.1.101.26.29.1.6

rlInternInetCidrRouteTable

table
.1.3.6.1.4.1.9.6.1.101.26.30 · 1 row entry · 19 columns
Open in standard view 
Internal inetCidrRouteTable - this entity's IP Routing table.
rlInternInetCidrRouteEntry entry .1.3.6.1.4.1.9.6.1.101.26.30.1
A particular route to a particular destination, under a
particular policy (as reflected in the
rlInternInetCidrRoutePolicy object).

Dynamically created rows will survive an agent reboot.

Implem…
Indexes
rlInternInetCidrRouteDestType rlInternInetCidrRouteDest rlInternInetCidrRoutePfxLen rlInternInetCidrRoutePolicy rlInternInetCidrRouteNextHopType rlInternInetCidrRouteNextHop
Column Syntax OID
rlInternInetCidrRouteDestType
The type of the rlInternInetCidrRouteDest address, as defined
in the InetAddress MIB.

Only those address types that may appear in an actual
routing table are allowed as values of this object.
INET-ADDRESS-MIBInetAddressType
Constraints:
range: 0-80
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.26.30.1.1
rlInternInetCidrRouteDest
The destination IP address of this route.

The type of this address is determined by the value of
the rlInternInetCidrRouteDestType object.

The values for the index objects rlInternInetCidrR…
INET-ADDRESS-MIBInetAddress
Enumerated Values:
2image1
3image2
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.26.30.1.2
rlInternInetCidrRoutePfxLen
Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlInternInetCidrRouteDest field.

The values for the i…
INET-ADDRESS-MIBInetAddressPrefixLength
Enumerated Values:
1enable
2disable
Constraints:
range: 0-31
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.26.30.1.3
rlInternInetCidrRoutePolicy
This object is an opaque object without any defined
semantics. Its purpose is to serve as an additional
index that may delineate between multiple entries to
the same destination. The value { 0 0 } shall be used
as the…
ObjectIdentifier
Enumerated Values:
1enable
2disable
Constraints:
range: 0-31
 .1.3.6.1.4.1.9.6.1.101.26.30.1.4
rlInternInetCidrRouteNextHopType
The type of the rlInternInetCidrRouteNextHop address, as
defined in the InetAddress MIB.

Value should be set to unknown(0) for non-remote
routes.

Only those address types that may appear in…
INET-ADDRESS-MIBInetAddressType
Enumerated Values:
1inProgress
2notInProgress
3finishedWithSuccess
4finishedWithError
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.26.30.1.5
rlInternInetCidrRouteNextHop
On remote routes, the address of the next system en
route. For non-remote routes, a zero length string.

The type of this address is determined by the value of
the rlInternInetCidrRouteNextHopType objec…
INET-ADDRESS-MIBInetAddress
Enumerated Values:
1unassigned
2standby-opr
3standby-cfg
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.26.30.1.6
rlInternInetCidrRouteIfIndex
The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified.
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.30.1.7
rlInternInetCidrRouteType
The type of route. Note that local(3) refers to a
route for which the next hop is the final destination;
remote(4) refers to a route for which the next hop is
not the final destination.

Routes that do no…
Enumeration .1.3.6.1.4.1.9.6.1.101.26.30.1.8
rlInternInetCidrRouteProto
The routing mechanism via which this route was learned.
Inclusion of values for gateway routing protocols is
not intended to imply that hosts should support those
protocols.
IANA-RTPROTO-MIBIANAipRouteProtocol
Constraints:
range: -1-255
Textual Convention: IANA-RTPROTO-MIBIANAipRouteProtocol Enumeration
Type Values:
1other
2local
3netmgmt
4icmp
5egp
6ggp
7hello
8rip
9isIs
10esIs
11ciscoIgrp
12bbnSpfIgp
13ospf
14bgp
15idpr
16ciscoEigrp
17dvmrp
18rpl
19dhcp
20ttdp
 .1.3.6.1.4.1.9.6.1.101.26.30.1.9
rlInternInetCidrRouteAge
The number of seconds since this route was last updated
or otherwise determined to be correct. Note that no
semantics of 'too old' can be implied, except through
knowledge of the routing protocol by which the route
was…
SNMPv2-SMIGauge32
Enumerated Values:
1empty
2full
3error
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.30.1.10
rlInternInetCidrRouteNextHopAS
The Autonomous System Number of the Next Hop. The
semantics of this object are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. When this object is unknown or not relevant…
INET-ADDRESS-MIBInetAutonomousSystemNumber
Enumerated Values:
1enable
2disable
Textual Convention: INET-ADDRESS-MIBInetAutonomousSystemNumber Unsigned32
 .1.3.6.1.4.1.9.6.1.101.26.30.1.11
rlInternInetCidrRouteMetric1
The primary routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should b…
SNMPv2-SMIInteger32
Enumerated Values:
1enable
2disable
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.30.1.12
rlInternInetCidrRouteMetric2
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should …
SNMPv2-SMIInteger32
Constraints:
range: 0-255
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.30.1.13
rlInternInetCidrRouteMetric3
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should …
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.30.1.14
rlInternInetCidrRouteMetric4
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should …
SNMPv2-SMIInteger32
Enumerated Values:
0pluggable
1power-down
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.30.1.15
rlInternInetCidrRouteMetric5
An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should …
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.30.1.16
rlInternInetCidrRouteStatus
The row status variable, used according to row
installation and removal conventions.

A row entry cannot be modified when the status is
marked as active(1).
SNMPv2-TCRowStatus
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.6.1.101.26.30.1.17
rlInternInetCidrRouteLifetime
The remaining length of time, in seconds, that this route
will continue to be valid, i.e., time until deprecation.
A value of 4,294,967,295 represents infinity.
secondsSNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.30.1.18
rlInternInetCidrRouteInfo
A reference to MIB definitions specific to the particular routing
protocol which is responsible for this route, as determined by the
value specified in the route's inetCidrRouteProto value.
Enumeration .1.3.6.1.4.1.9.6.1.101.26.30.1.19

rlInternInetStaticRouteTable

table
.1.3.6.1.4.1.9.6.1.101.26.31 · 1 row entry · 11 columns
Open in standard view 
This entity's static (user configured) Inet Routing table.
Entries are MAX-ACCESSible even if not used for forwarding
rlInternInetStaticRouteEntry entry .1.3.6.1.4.1.9.6.1.101.26.31.1
A particular Static(user configured) route to a particular destination.
Indexes
rlInternInetStaticRouteDestType rlInternInetStaticRouteDest rlInternInetStaticRoutePfxLen rlInternInetStaticRouteNextHopType rlInternInetStaticRouteNextHop rlInternInetStaticRouteIfIndex
Column Syntax OID
rlInternInetStaticRouteDestType
The type of the address used as the destination
internetwork address or subnet address.
INET-ADDRESS-MIBInetAddressType
Constraints:
range: 0-899
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.26.31.1.1
rlInternInetStaticRouteDest
Destination internetwork address or subnet address. The
destination prefix length is applied to this value, and to a
particular destination address, to determine whether the route
applies to the particular address.
If …
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.26.31.1.2
rlInternInetStaticRoutePfxLen
Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlInternInetStaticRouteDest field.
INET-ADDRESS-MIBInetAddressPrefixLength
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.26.31.1.3
rlInternInetStaticRouteNextHopType
The type of the address used as the next-hop address
for this route.
INET-ADDRESS-MIBInetAddressType
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.26.31.1.4
rlInternInetStaticRouteNextHop
The next-hop IP address, if any.
If rlInternInetStaticRouteAction is 'forward', there may or may not be
a next-hop IP address.
A next-hop IP address is not required if an output interface
index is specified (in other wo…
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.26.31.1.5
rlInternInetStaticRouteIfIndex
The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified.
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.6.1.101.26.31.1.6
rlInternInetStaticRoutePathCost
Path cost for this static route. Value of 0 signs default value metric
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.26.31.1.7
rlInternInetStaticRouteType
Same as inetCidrRouteType MIB (excluded 'other' route type)
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.26.31.1.8
rlInternInetStaticRouteOwner
Static - The route is configured over Static IP.
This route is written to configuration files.
Dhcp - The route is Configured by DHCP
(received as part of DHCP configuration)
This route IS NOT written to configurati…
Enumeration .1.3.6.1.4.1.9.6.1.101.26.31.1.9
rlInternInetStaticRouteRowStatus
The row status variable, used according to row
installation and removal conventions.
A row entry cannot be modified when the status is
marked as active(1).
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.6.1.101.26.31.1.10
rlInternInetStaticRouteForwardingStatus
active - An indication that the route has implication on routing
inactive - the route is a backup route or it is down. It is not used
in forwarding decision.
Down means that the Ip interface on which it is co…
Enumeration
Enumerated Values:
1stack
2ethernet
 .1.3.6.1.4.1.9.6.1.101.26.31.1.11

rlIpv6GeneralPrefixTable

table
.1.3.6.1.4.1.9.6.1.101.129.4 · 1 row entry · 6 columns
Open in standard view 
This table defines general prefix description,
based on which a number of longer, more specific, prefixes can
be defined.
rlIpv6GeneralPrefixEntry entry .1.3.6.1.4.1.9.6.1.101.129.4.1
Single entry in general prefix table.
Indexes
rlIpv6GeneralPrefixName
Column Syntax OID
rlIpv6GeneralPrefixName
The name assigned to the prefix.
SNMPv2-TCDisplayString
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.4.1.1
rlIpv6GeneralPrefixInetAddrType
Prefix inet address type. Has to be IPv6.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.129.4.1.2
rlIpv6GeneralPrefixInetAddr
The IPv6 network assigned to the general prefix.
This argument must be in the form documented in RFC4293
where the address is specified in hexadecimal using 16-bit values
between colons.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.4.1.3
rlIpv6GeneralPrefixInetAddrPrefixLength
Indicates the number of leading one bits that form the
mask to be logical-ANDed with the inet address
before being compared to the value in the
rlIpv6GeneralPrefixInetAddr field.
INET-ADDRESS-MIBInetAddressPrefixLengthr/w
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.129.4.1.4
rlIpv6GeneralPrefixInterfaceId
Interface id to use when creating prefix based on point-to-point interface.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.4.1.5
rlIpv6GeneralPrefixRowStatus
Row status.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.6.1.101.129.4.1.6

rlIpv6RouterAdvertPrefixTable

table
.1.3.6.1.4.1.9.6.1.101.129.6 · 1 row entry · 12 columns
Open in standard view 
This table defines IPv6 prefixes which are included in IPv6 Neighbor
Discovery (ND) router advertisements.
rlIpv6RouterAdvertPrefixEntry entry .1.3.6.1.4.1.9.6.1.101.129.6.1
Single entry in Neighbor Discovery Prefix table.
Indexes
rlIpv6RouterAdvertPrefixIfIndex rlIpv6RouterAdvertPrefixIsDefault rlIpv6RouterAdvertPrefixInetAddrType rlIpv6RouterAdvertPrefixInetAddr rlIpv6RouterAdvertPrefixInetAddrPrefixLength
Column Syntax OID
rlIpv6RouterAdvertPrefixIfIndex
The index value that uniquely identifies the interface on
which this prefix is configured. The interface identified
by a particular value of this index is the same interface as
identified by the same value of the IF-MI…
IF-MIBInterfaceIndex
Constraints:
range: 0-96
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.9.6.1.101.129.6.1.1
rlIpv6RouterAdvertPrefixIsDefault
Indicates whether this object belongs to 'default' entry.
Default entry contains specifics about advertising prefixes which
were created from local ipv6 addresses.
SNMPv2-TCTruthValue
Constraints:
range: 0-96
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.129.6.1.2
rlIpv6RouterAdvertPrefixInetAddrType
Prefix inet address type. Has to be IPv6.
INET-ADDRESS-MIBInetAddressType
Constraints:
range: 0-899
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.129.6.1.3
rlIpv6RouterAdvertPrefixInetAddr
The IPv6 network prefix to include in router advertisements.
This argument must be in the form documented in RFC4293 where
the address is specified in hexadecimal using 16-bit values between
colons.
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.6.1.4
rlIpv6RouterAdvertPrefixInetAddrPrefixLength
The length of the IPv6 prefix. A decimal value that indicates
how many of the high-order contiguous bits of the address comprise
the prefix (the network portion of the address).
INET-ADDRESS-MIBInetAddressPrefixLength
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.129.6.1.5
rlIpv6RouterAdvertPrefixAdminStatus
Admin status of the entry. Relevant only for default entry.
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.129.6.1.6
rlIpv6RouterAdvertPrefixAdvertise
Whether the prefix is included in router advertisements.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.129.6.1.7
rlIpv6RouterAdvertPrefixOnLinkStatus
If object has the value 'onlink(1)', this prefix is confidered as on-link.
This prefix will be advertised with the L-bit set and will be present
in the Routing Table.
If object has the value 'not-onlink(2)', this prefix…
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.129.6.1.8
rlIpv6RouterAdvertPrefixAutonomousFlag
If object has the value 'true(1)', this prefix indicates to hosts on
the local link that the specified prefix can be used for IPv6
autoconfiguration. The prefix will be advertised with the A-bit set.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.129.6.1.9
rlIpv6RouterAdvertPrefixAdvPreferredLifetime
The amount of time (in seconds) that the specified IPv6 prefix is
advertised as being preferred.
secondsSNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.6.1.10
rlIpv6RouterAdvertPrefixAdvValidLifetime
The amount of time (in seconds) that the specified IPv6 prefix is
advertised as being valid.
secondsSNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.6.1.11
rlIpv6RouterAdvertPrefixRowStatus
Row status.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.6.1.101.129.6.1.12

rlIpv6RouterAdvertTable

table
.1.3.6.1.4.1.9.6.1.101.129.7 · 1 row entry · 3 columns
Open in standard view 
This table is parallel to inetCidrRouteTable, and is used to
configure or display additional route parameters.
rlIpv6RouterAdvertEntry entry .1.3.6.1.4.1.9.6.1.101.129.7.1
Additional parameters for a particular route.
Indexes
No indexes recorded
Column Syntax OID
rlIpv6RouterAdvertAdvIntervalOption
Indicates to a visiting mobile node the interval at which that node
may expect to receive RAs. The node may use this information in its
movement detection algorithm.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.129.7.1.1
rlIpv6RouterAdvertRouterPreference
Configures a default router preference (DRP) for the router on a specific interface.
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.129.7.1.2
rlIpv6RouterAdvertIsCurHopLimitUserConfigured
Indicates that hop limit value used in router advertisement is
an user configured value and not necessarily value that is used by
router itself.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.6.1.101.129.7.1.3

rlIpv6PathMtuTable

table
.1.3.6.1.4.1.9.6.1.101.129.9 · 1 row entry · 4 columns
Open in standard view 
This table used to represent all Path MTU changes to specific destination
received from 'packet-too-big' messages.
rlIpv6PathMtuEntry entry .1.3.6.1.4.1.9.6.1.101.129.9.1
Single entry in Path MTU table.
Indexes
rlIpv6PathMtuEntryInetDestAddrType IF-MIBifIndex rlIpv6PathMtuEntryInetDestAddr
Column Syntax OID
rlIpv6PathMtuEntryInetDestAddrType
Prefix inet address type. Has to be IPv6.
INET-ADDRESS-MIBInetAddressType
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.129.9.1.1
rlIpv6PathMtuEntryInetDestAddr
The IPv6 destination address for which packet-too-big message
was received.
This argument must be in the form documented in RFC4293
where the address is specified in hexadecimal using 16-bit values
between colons.
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.9.1.2
rlIpv6PathMtuEntryMtu
The MTU value that was received in packet-too-bug message for
specific destination.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.9.1.3
rlIpv6PathMtuEntryAge
This entry's age (seconds)
secondsSNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.9.1.4

rlIpNetToPhysicalTableClearTable

table
.1.3.6.1.4.1.9.6.1.101.129.10 · 1 row entry · 2 columns
Open in standard view 
This entity is used to clear all or specific-type entries from ipNetToPhysicalTable.
rlIpNetToPhysicalTableClearEntry entry .1.3.6.1.4.1.9.6.1.101.129.10.1
A particular entry in this table.
Indexes
rlIpNetToPhysicalTableClearIfIndex
Column Syntax OID
rlIpNetToPhysicalTableClearIfIndex
Interface index of to clear or zero in case of whole table.
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.6.1.101.129.10.1.1
rlIpNetToPhysicalTableClearScope
Scope of the action - type of entries to delete.
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.129.10.1.2

rlIpv6HostForwardingTable

table
.1.3.6.1.4.1.9.6.1.101.129.11 · 1 row entry · 8 columns
Open in standard view 
This entity's IPv6 host forwarding table.
rlIpv6HostForwardingEntry entry .1.3.6.1.4.1.9.6.1.101.129.11.1
A particular Static(user configured) route to a particular destination.
Indexes
rlIpv6HostForwardingDestType IF-MIBifIndex ADTRAN-GENERIC-IMA-MIBadGenImaGroupDayIntervalNumber rlIpv6HostForwardingDest rlIpv6HostForwardingPfxLen rlIpv6HostForwardingNextHopType rlIpv6HostForwardingNextHop rlIpv6HostForwardingIfIndex rlIpv6HostForwardingType
Column Syntax OID
rlIpv6HostForwardingDestType
The type of the address used as the destination
internetwork address or subnet address.
INET-ADDRESS-MIBInetAddressType
Constraints:
range: 1-7
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.129.11.1.1
rlIpv6HostForwardingDest
Destination internetwork address or subnet address.
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.11.1.2
rlIpv6HostForwardingPfxLen
Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlIpv6HostForwardingDest field.
INET-ADDRESS-MIBInetAddressPrefixLength
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.6.1.101.129.11.1.3
rlIpv6HostForwardingNextHopType
The type of the address used as the next-hop address
for this route.
INET-ADDRESS-MIBInetAddressType
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.129.11.1.4
rlIpv6HostForwardingNextHop
The next-hop IP address, if any.
A next-hop IP address is not required if an output interface
index is specified (in other words, if rlIpv6HostForwardingIfIndex is
non-zero).
If there is no next-hop IP address, the rlIp…
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.11.1.5
rlIpv6HostForwardingIfIndex
The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified.
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.6.1.101.129.11.1.6
rlIpv6HostForwardingType
Forwarding type
Enumeration .1.3.6.1.4.1.9.6.1.101.129.11.1.7
rlIpv6HostForwardingPathCost
Path cost for this route.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.11.1.8

rlIpv6TunnelToIPv6DbTable

table
.1.3.6.1.4.1.9.6.1.101.129.15 · 1 row entry · 8 columns
Open in standard view 
This entity's IPv6 Tunnel if/addr/prefix table.
rlIpv6TunnelToIPv6DbEntry entry .1.3.6.1.4.1.9.6.1.101.129.15.1
A particular tunnel configured data to IPv6 db.
Indexes
rlIpv6TunnelToIPv6IfIndex
Column Syntax OID
rlIpv6TunnelToIPv6IfIndex
IfIndex of tunnel interface
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.9.6.1.101.129.15.1.1
rlIpv6TunnelToIPv6Action
Action of the entry. All other fields relevant for appropriate actions.
Enumerationr/w .1.3.6.1.4.1.9.6.1.101.129.15.1.2
rlIpv6TunnelToIPv6TunnelType
Tunnel type (manual/isatap/6to4/...).
IANAifType-MIBIANAtunnelTyper/w
Textual Convention: IANAifType-MIBIANAtunnelType Enumeration
Type Values:
1other
2direct
3gre
4minimal
5l2tp
6pptp
7l2f
8udp
9atmp
10msdp
11sixToFour
12sixOverFour
13isatap
14teredo
15ipHttps
16softwireMesh
17dsLite
18aplusp
19ipsectunnelmode
 .1.3.6.1.4.1.9.6.1.101.129.15.1.3
rlIpv6TunnelToIPv6Address
The address used for this tunnel. Could be local IPv4 of the tunnel.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.15.1.4
rlIpv6TunnelToIPv6PrefixLength
The address/prefix length used for above address if applicable.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.15.1.5
rlIpv6TunnelToIPv6Mtu
Mtu of this interface. Used for host isatap tunnels
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.15.1.6
rlIpv6TunnelToIPv6MinRtrSolicitationInterval
Minimal router solicitation interval. Used for host isatap tunnels
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.6.1.101.129.15.1.7
rlIpv6TunnelToIPv6LinkLayerIPv4
IPv4 address used for link-layer of ipv6 over ipv4 tunnel
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.6.1.101.129.15.1.8

rlInetStaticRouteAuxMappingTable

table
.1.3.6.1.4.1.9.6.1.101.129.19 · 1 row entry · 3 columns
Open in standard view 
This entity's IPv6 auxulary mapping table. Serves to map nexthop ipv6 address to on-link prefix ifindex
rlInetStaticRouteAuxMappingEntry entry .1.3.6.1.4.1.9.6.1.101.129.19.1
An Auxulary Mapping table to find onlink prefix ifindex for ipv6 static route.
Indexes
rlInetStaticRouteAuxMappingNextHopType rlInetStaticRouteAuxMappingNextHop
Column Syntax OID
rlInetStaticRouteAuxMappingNextHopType
The type of the address used as the next-hop address
for this route.
INET-ADDRESS-MIBInetAddressType
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.6.1.101.129.19.1.1
rlInetStaticRouteAuxMappingNextHop
The next-hop IP address
INET-ADDRESS-MIBInetAddress
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.6.1.101.129.19.1.2
rlInetStaticRouteAuxMappingNextHopIfIndex
The ifIndex mapped to specified necthop address
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.6.1.101.129.19.1.3