CISCO-VISM-CONN-STAT-MIB Table View

This object identifies the LCN(Logical Channel
Number) on the VISM.

This object is use to either reset counters or
perform no action(do not clear counters).

This object keep count of egress AAL2(ATM
Adaptation layer 2) CPS(Common Part Sub-layer)
PDU(Protocol Data Unit) dropped due to HEC(Header
Error Control) error.

This object keeps track of egress AAL2 Type3
CPS PDUs dropped due to invalid CRC-10(Cyclic
redundancy check) error. CRC validation is for
Type 3 packets only. Type 1 packets are not
subjected to CRC-10 error validation.…

This object keeps track of the number of
OAM(Operation and management) loopback cells
lost. OAM loopback cells are sent on a periodic
basis (1 sec) on each PVC(Permanent Virtual
Circuit) to monitor the health of the P…

This object keeps track of the number AAL2 cells
dropped due to invalid OSF (OffSet Field) in
the egress direction.

This object keeps track of the number of AAL2
cells dropped due to invalid Parity bit field
in the egress direction.

This object keeps track of the number of AAL2
CPS packets sent to the network.

This object keeps track of AAL2 CPS packets
received from the network. This does not include
the packets which are counted as error packets.

This object keeps track of AAL2 CPS packets
dropped in the egress direction due to invalid
CID(Channel Identifier). The CID may be
considered as invalid if it is out of range or
not configured.

This object keeps track of AAL2 CPS packets
dropped in the egress direction due to invalid
UUI (User-to-User Information) field.

This object keeps track of AAL2 CPS packets
dropped in the egress direction due to invalid
length field.

This object counts the number of AAL5 PDUs
dropped in the egress direction due to invalid
CPI(Common Part Indicator) field in the AAL5 PDU
trailer. This is applicable only to the PVCs
configured as AAL5 PVCs (VoIP(Voice…

This object counts the number AAL5 PDUs
dropped due to the SDU(Service Data Unit)
size bigger than the configured value. This
is applicable for AAL5 PVCs only.

This object counts the number of AAL5 PDUs
dropped due to the length violations. This is
applicable to the CCS PVCs. The HDLC(High Level
Data Link Control) frames should have a minimum
frame size in order for the proper…

This object counts the number of AAL5 PDUs
dropped in the egress direction due to CRC-32
errors detected by the SAR(Segmentation and
Reassembly).

This object counts of AAL5 PDU reassembly
timer expirations. The timers are maintained
in the egress direction for building an AAL5
PDU from the cells.

This object counts the peak transmit cell rate
(cells per second) for the channel since midnight
with reference to node time;
the peak cell rate counter gets reset to 0
every 24 hours at midnight.
If the node time is…

This object counts the current transmit cell
rate (cells per second) for the channel.

This object counts the peak receive cell rate
(cells per second) for the channel since midnight
with reference to node time;
the peak cell rate counter gets reset to 0
every 24 hours at midnight.
If the node time is …

This object counts the current receive cell
rate (cells per second) for the channel.

This object holds the number of times that ATM network
alarms were successfully suppressed and prevented from
propagating onto the TDM side for this PVC.

The number of instances that an ATM AIS alarm was
transmitted.

The number of instances that an ATM AIS alarm was
received.

The number of instances that an ATM FERF alarm was
transmitted.

The number of instances that an ATM FERF alarm was
received.

This object counts the number of AAL5 PDUs transmitted
to the network. This is only applicable to the PVCs
configured as AAL5 PVCs, VoIP (Voice Over IP) PVCs
or CCS (Common Channel Signaling) PVCs in the case of
VoA…

This object counts the number of AAL5 PDUs received
from the network. This is only applicable to the PVCs
configured as AAL5 PVCs, VoIP (Voice Over IP) PVCs
or CCS (Common Channel Signaling) PVCs in the case of
VoAA…

The real-time number of seconds remaining for the AIS
delay timer after which the ATM alarm will be propagated
to the TDM side.
This object is tied to the vismChanAisDelayTime object
in the CISCO-VISM-CONN-MIB. vismC…

The number of instances that OAM loopback
timeout alarm has occurred since the system
was last re-initialized.

The total duration of OAM loopback timeout
alarms since the system was last
re-initialized.