A3Com-Dvmrp-r1-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
11
Rows
11
Columns
65

a3ComDvmrpPortTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.1 · 1 row entry · 5 columns
Open in standard view 
This table contains entries of parameters associated with every port
or tunnel.
a3ComDvmrpPortEntry entry .1.3.6.1.4.1.43.2.28.2.1.1
Each entry contains information for a spcified port or tunnel.
Indexes
a3ComDvmrpPortIndex
Column Syntax OID
a3ComDvmrpPortIndex mandatory
The port number or tunnel ID of which this entry applies. The
tunnel ID starts with 1025 and end with 1056, i.e. total tunnel
number is limited to 32.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.1.1.1
a3ComDvmrpPortControl mandatory
This object allows the multicast routing to run with DVMRP or not.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.28.2.1.1.2
a3ComDvmrpPortMetric mandatory
This object specifies the cost to the given port or tunnel. A value
of 32 is considered 'infinity'.
Integer32r/w
Constraints:
range: 1-31
 .1.3.6.1.4.1.43.2.28.2.1.1.3
a3ComDvmrpPortRateLimit mandatory
This object specifies the bandwidth in Kbits/second that will be
allocated for the multicast datagrams traffic. If set the value to
0 then the full bandwidth of the port will be applied.
Integer32r/w
Constraints:
range: 0-100000
 .1.3.6.1.4.1.43.2.28.2.1.1.4
a3ComDvmrpPortAggregateCtrl mandatory
This object controls the way to advertise routes.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.28.2.1.1.5

a3ComDvmrpBoundaryAddrTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.2 · 1 row entry · 4 columns
Open in standard view 
This table contains multicast addresses to be scoped for each port or
tunnel.
a3ComDvmrpBoundaryAddrEntry entry .1.3.6.1.4.1.43.2.28.2.2.1
Each entry contains a single or a range of multicast addresses to be
scoped over a specific port or tunnel.
Indexes
a3ComDvmrpBoundaryAddrPort a3ComDvmrpBoundaryAddrIpAddr
Column Syntax OID
a3ComDvmrpBoundaryAddrPort mandatory
The port or tunnel number to which this entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.2.1.1
a3ComDvmrpBoundaryAddrIpAddr mandatory
This allows you to configure a single or a set of multicast
addresses to be scoped that they do not get forwarded beyond a
boundary router.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.2.1.2
a3ComDvmrpBoundaryAddrMask mandatory
This is the subnet mask associated with a3ComDvmrpBoundaryIpAddr of
this entry. If this is not specified, the value 255.255.255.255 is
used.
RFC1155-SMIIpAddressr/w
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.2.1.3
a3ComDvmrpBoundaryAddrStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.2.1.4

a3ComDvmrpMospfTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.3 · 1 row entry · 5 columns
Open in standard view 
This table contains a list of source subnet in MOSPF domain.
a3ComDvmrpMospfEntry entry .1.3.6.1.4.1.43.2.28.2.3.1
Each entry contains a source subnet in MOSPF domain to be advertised
or not to be advertised to the DVMRP domain.
Indexes
a3ComDvmrpMospfIpAddr a3ComDvmrpMospfIpMask
Column Syntax OID
a3ComDvmrpMospfIpAddr mandatory
Source subnet's IP address.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.3.1.1
a3ComDvmrpMospfIpMask mandatory
This is subnet mask associated with a3ComDvmrpMospfIpAddr. It is
a number of contiguous leading 1s, i.e. if the value is 1, it
indicates the subnet mask is 128.0.0.0, or if the value is 8 then
the subnet mask is 255.0.0…
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.3.1.2
a3ComDvmrpMospfMetric mandatory
The routing metric to this source subnet. It ranges from 1 to 31.
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.3.1.3
a3ComDvmrpMospfAction mandatory
If this object is set to aggregate(1), then this source subnet, if
learned from MOSPF, is advertised to DVMRP domain in aggregate form.
If this object is set to individual(2), then this source subnet, if
learned from MO…
Enumerationr/w
Enumerated Values:
1aggregate
2individual
3reject
 .1.3.6.1.4.1.43.2.28.2.3.1.4
a3ComDvmrpMospfStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.3.1.5

a3ComDvmrpNeighborTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.4 · 1 row entry · 4 columns
Open in standard view 
This table contains a list of neighbors entries for each X.25 or
Frame-Relay networks.
a3ComDvmrpNeighborEntry entry .1.3.6.1.4.1.43.2.28.2.4.1
Each entry contains a single X.25 DTE address or a Frame-Relay DLCI.
Indexes
a3ComDvmrpNeighborPort a3ComDvmrpNeighborType a3ComDvmrpNeighborAddr
Column Syntax OID
a3ComDvmrpNeighborPort mandatory
The port number to which this entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.4.1.1
a3ComDvmrpNeighborType mandatory
This object specifies the media type of the port.
Enumeration
Enumerated Values:
2x25
4frame-relay
 .1.3.6.1.4.1.43.2.28.2.4.1.2
a3ComDvmrpNeighborAddr mandatory
This object specifies an X.25 DTE address or a Frame-Relay DLCI.
RFC1213-MIBPhysAddress
Textual Convention: RFC1213-MIBPhysAddress OctetString
 .1.3.6.1.4.1.43.2.28.2.4.1.3
a3ComDvmrpNeighborStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.4.1.4

a3ComDvmrpTunnelTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.5 · 1 row entry · 5 columns
Open in standard view 
This table contains entries of tunnel.
a3ComDvmrpTunnelEntry entry .1.3.6.1.4.1.43.2.28.2.5.1
Each entry contains parameters associated with a specific tunnel.
Indexes
a3ComDvmrpTunnelId
Column Syntax OID
a3ComDvmrpTunnelId mandatory
The ID number of which this entry applies. Tunnel ID starts with
1025 and ends with 1056.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.5.1.1
a3ComDvmrpTunnelLocalIp mandatory
This object specifies the IP address of local end of a tunnel. It
must be one of system's directly connected subnet.
RFC1155-SMIIpAddressr/w
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.5.1.2
a3ComDvmrpTunnelRemoteIp mandatory
This object specifies the IP address of remote end of a tunnel.
RFC1155-SMIIpAddressr/w
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.5.1.3
a3ComDvmrpTunnelTtl mandatory
This object specifies the value to be put in IP packet's TTL field
when transmits packets through a tunnel.
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.43.2.28.2.5.1.4
a3ComDvmrpTunnelStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.5.1.5

a3ComDvmrpAggreExceptTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.6 · 1 row entry · 3 columns
Open in standard view 
The table contains list of subnets not to be aggregated.
a3ComDvmrpAggreExceptEntry entry .1.3.6.1.4.1.43.2.28.2.6.1
Each entry contains a range of subnets.
Indexes
a3ComDvmrpAggreExceptIpAddr a3ComDvmrpAggreExceptIpMask
Column Syntax OID
a3ComDvmrpAggreExceptIpAddr mandatory
This object specifies the IP subnet address.
RFC1155-SMIIpAddressr/w
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.6.1.1
a3ComDvmrpAggreExceptIpMask mandatory
The subnet mask of ccsIpDvmrpAggreExceptIpAddr. It is an
integer value representing number of consecutive leading 1s. i.e.
if the value is 1, then the subnet mask is 128.0.0.0, if the value
is 8 then the subnet mask is …
Integer32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.43.2.28.2.6.1.2
a3ComDvmrpAggreExceptStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.6.1.3

a3ComDvmrpAggreRangeTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.7 · 1 row entry · 4 columns
Open in standard view 
The table contains range of routes to be aggregated.
a3ComDvmrpAggreRangeEntry entry .1.3.6.1.4.1.43.2.28.2.7.1
Each entry contains a range of routes.
Indexes
a3ComDvmrpAggreRangeIpAddr a3ComDvmrpAggreRangeIpMask
Column Syntax OID
a3ComDvmrpAggreRangeIpAddr mandatory
This object specifies the IP subnet address.
RFC1155-SMIIpAddressr/w
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.7.1.1
a3ComDvmrpAggreRangeIpMask mandatory
The subnet mask of ccsIpDvmrpAggreRangeIpAddr. It is an
integer value representing number of consecutive leading 1s. i.e.
if the value is 1, then the subnet mask is 128.0.0.0, if the value
is 8 then the subnet mask is 2…
Integer32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.43.2.28.2.7.1.2
a3ComDvmrpAggreRangeMetric mandatory
This object specifies the cost to the above subnet. If set this
object to value 0, the metric associated with the aggregate route
to be advertised will pick up the best one among all the aggregated
routes.
Integer32r/w
Constraints:
range: 0-31
 .1.3.6.1.4.1.43.2.28.2.7.1.3
a3ComDvmrpAggreRangeStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.7.1.4

a3ComDvmrpDestGroupTable

table mandatory
.1.3.6.1.4.1.43.2.28.2.8 · 1 row entry · 4 columns
Open in standard view 
The table contains destination groups to be or not to be forwarded
to MOSPF domain. This table will take effect only if object
a3ComDvmrpDestGroupPolicy is set to 'destGroup (1)'.
a3ComDvmrpDestGroupEntry entry .1.3.6.1.4.1.43.2.28.2.8.1
Each entry contains a destination group to be or not to be forwarded
to MOSPF domain.
Indexes
a3ComDvmrpDestGroupIpAddr a3ComDvmrpDestGroupIpMask
Column Syntax OID
a3ComDvmrpDestGroupIpAddr mandatory
This object specifies the destination group IP address, the first
byte in decimal must be in the range of 224 to 239.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.2.8.1.1
a3ComDvmrpDestGroupIpMask mandatory
This is subnet mask associated with a3ComDvmrpDestGroupIpAddr. It is
a number of contiguous leading 1s, i.e. if the value is 1, it
indicates the subnet mask is 128.0.0.0, or if the value is 8 then
the subnet mask is 255…
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.2.8.1.2
a3ComDvmrpDestGroupAction mandatory
This object specifies if this destination group needs to be
forwarded to MOSPF domain. If set to 'accept (1)', the group is
forwarded to MOSPF domain; if set to 'reject (2)' then the group
is filtered out.
Enumerationr/w
Enumerated Values:
1accept
2reject
 .1.3.6.1.4.1.43.2.28.2.8.1.3
a3ComDvmrpDestGroupStatus mandatory
This object is used to add and delete entries in this table. See
the definition of RowStatus for detail.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.28.2.8.1.4

a3ComDvmrpRouteTable

table mandatory
.1.3.6.1.4.1.43.2.28.3.1 · 1 row entry · 13 columns
Open in standard view 
This table contains multicast route information.
a3ComDvmrpRouteEntry entry .1.3.6.1.4.1.43.2.28.3.1.1
Each entry contains route information to a specific subnet or source.
Indexes
a3ComDvmrpRouteSource
Column Syntax OID
a3ComDvmrpRouteSource mandatory
The source IP address of this route.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.3.1.1.1
a3ComDvmrpRouteMask mandatory
This object is logical-anded with the source address before
comparing to the value in previous object a3ComDvmrpRouteSource.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.3.1.1.2
a3ComDvmrpRoutePreHop mandatory
The IP address of the upstream router of this route.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.3.1.1.3
a3ComDvmrpRouteMetric mandatory
The routing metric of this route. It's routing-protocol
dependenable, for DVMRP, the metric should be in range 1 to 31.
The value 32 is considered 'infinity' or unreachable.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.1.1.4
a3ComDvmrpRoutePort mandatory
The port number identifies from which this route comes.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.1.1.5
a3ComDvmrpRouteType mandatory
The type of route.
Enumeration
Enumerated Values:
1other
2direct
3remote
 .1.3.6.1.4.1.43.2.28.3.1.1.6
a3ComDvmrpRouteStatus mandatory
The status of route.
Enumeration
Enumerated Values:
1other
2up
3down
4hold-down
5garbage-collection
 .1.3.6.1.4.1.43.2.28.3.1.1.7
a3ComDvmrpRouteProtocol mandatory
The routing algorithm to which this route applies.
Enumeration
Enumerated Values:
1other
2static
3dvmrp
4mospf
5cbt
6pim
 .1.3.6.1.4.1.43.2.28.3.1.1.8
a3ComDvmrpRouteTtl mandatory
The time in seconds this route was last updated.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.1.1.9
a3ComDvmrpRouteChild mandatory
This object identifies ports that connect to child subtree of the
multicast tree rooted at a3ComDvmrpRouteSource. Each octet, except
the first one which contains a value specified length of this
object, contains a bit m…
OctetString .1.3.6.1.4.1.43.2.28.3.1.1.10
a3ComDvmrpRouteChildTunnel mandatory
This object is the same as above but includes tunnel ports only.
The first (should say the second) octet specifies ports from 1025
(for tunnel port 1) to 1032, the next octet specifies ports 1033 to
1040, ... etc.
OctetString .1.3.6.1.4.1.43.2.28.3.1.1.11
a3ComDvmrpRouteLeaf mandatory
This objec identifies ports that connect to leaf subnet of the
multicast tree rooted at a3ComDvmrpRouteSource. The value meaning
within each octet is the same as that of a3ComDvmrpRouteChild, except
the bit set means th…
OctetString .1.3.6.1.4.1.43.2.28.3.1.1.12
a3ComDvmrpRouteLeafTunnel mandatory
This objec is the same as a3ComDvmrpRouteLeaf object but includes
tunnel ports only.
OctetString .1.3.6.1.4.1.43.2.28.3.1.1.13

a3ComDvmrpForwardTable

table mandatory
.1.3.6.1.4.1.43.2.28.3.2 · 1 row entry · 8 columns
Open in standard view 
This table contains information of each (source, group) pair.
a3ComDvmrpForwardEntry entry .1.3.6.1.4.1.43.2.28.3.2.1
Each entry contains forwarding information for a specific (source,
group) pair.
Indexes
a3ComDvmrpForwardSource a3ComDvmrpForwardGroup
Column Syntax OID
a3ComDvmrpForwardSource mandatory
This object specifies root's IP address of this (source, group)
multicast distribution tree.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.3.2.1.1
a3ComDvmrpForwardGroup mandatory
This object specifies the destination multicast group address of
this (source, group) multicast distribution tree.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.3.2.1.2
a3ComDvmrpForwardTtl mandatory
This object specifies the time in seconds left for this (source,
group) entry to stay in the forwarding table. When this value
reaches 0, this (source, group) entry is deleted from the table.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.2.1.3
a3ComDvmrpForwardInPort mandatory
This object specifies the incoming port for the multicast
datagrams from the source a3ComDvmrpForwardSource.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.2.1.4
a3ComDvmrpForwardOutPorts mandatory
This object specifies ports to which multicast datagrams
belonging to this (source, group) pair to be forwarded. The value
in each octet contains a bit maps of 8 ports, that the significant
bit represents the lowest por…
OctetString .1.3.6.1.4.1.43.2.28.3.2.1.5
a3ComDvmrpForwardOutPortsTunnel mandatory
This object is the same as a3ComDvmrpForwardOutPorts object but
includes tunnel ports mapping only.
OctetString .1.3.6.1.4.1.43.2.28.3.2.1.6
a3ComDvmrpForwardScoped mandatory
This object specifies if it is a boundary port. If the value of
this object is yes(1), it means multicast traffic will not be
forwarded on the scoped address, specified in 3ComDvmrpForwardGroup,
on this port.
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.43.2.28.3.2.1.7
a3ComDvmrpForwardPruneSent mandatory
This object specifies if a Prune message has been sent to its
upstream router. A prune message is sent when router wants to leave
the multicast delivery tree associated with this (source, group)
pair.
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.43.2.28.3.2.1.8

a3ComDvmrpNbrRouterTable

table mandatory
.1.3.6.1.4.1.43.2.28.3.3 · 1 row entry · 10 columns
Open in standard view 
This table contains information of each neighboring router.
a3ComDvmrpNbrRouterEntry entry .1.3.6.1.4.1.43.2.28.3.3.1
Each entry contains neighboring router's IP address, DVMRP version,
generation ID, expiration time and status.
Indexes
a3ComDvmrpNbrRouterPort a3ComDvmrpNbrRouterIpAddr
Column Syntax OID
a3ComDvmrpNbrRouterPort mandatory
The port number or tunnel ID of which this entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.3.1.1
a3ComDvmrpNbrRouterIpAddr mandatory
The IP address of this neighboring router.
RFC1155-SMIIpAddress
Textual Convention: RFC1155-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.28.3.3.1.2
a3ComDvmrpNbrRouterGenId mandatory
The generation ID of this neighboring router.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.3.1.3
a3ComDvmrpNbrRouterVerProtocol mandatory
The version of DVMRP protocol that this neighboring router is
running.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.3.1.4
a3ComDvmrpNbrRouterVerMrouted mandatory
The version of 'mrouted' that this neighboring router is running.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.3.1.5
a3ComDvmrpNbrRouterTtl mandatory
The time in seconds left for this neighboring router. When the
value reaches 0, this entry is deleted from the table.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.28.3.3.1.6
a3ComDvmrpNbrRouterLeafStatus mandatory
This object specifies if this neighboring router is a leaf node.
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.43.2.28.3.3.1.7
a3ComDvmrpNbrRouterPruneStatus mandatory
This object specifies if this neighboring router supports DVMRP
prune.
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.43.2.28.3.3.1.8
a3ComDvmrpNbrRouterGenIdStatus mandatory
This object specifies if this neighboring router provides generation
ID and its router list in the DVMRP probe packet.
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.43.2.28.3.3.1.9
a3ComDvmrpNbrRouterMtraceStatus mandatory
This object specifies if this neighboring router supports multicast
trace route.
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.43.2.28.3.3.1.10