wwpLeosMcastIgmpSnoopProxyQueryDelay

WWP-LEOS-MULTICAST-FILTER-MIB · .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.5

MIB view Table view

Object

column r/w seconds Integer32

The amount of time to wait before sending the next 
group specific query downstream.  
General queries are sent one port at a time.

Context

MIB: WWP-LEOS-MULTICAST-FILTER-MIB
OID: .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.5
Type: column
Access: readwrite
Status: current
Units: seconds
Parent: wwpLeosMcastIgmpSnoopEntry
Table: wwpLeosMcastIgmpSnoopTable
Siblings: 18

Syntax

seconds Integer32

Values & Constraints

Object Constraints

range: 1-100

Related Objects

Sibling Objects

Object	Type	Syntax	OID
wwpLeosMcastIgmpSnoopEnable For LEOS (4.x) IGMP snooping can be enabled on this VLAN by setting this object to 'true'. The Management station should define the router IP address range and the list of server…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.1`
wwpLeosMcastIgmpMinResponseTime Setting this object will set the minimum response time for given VLAN.	column	Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.10`
wwpLeosMcastIgmpDefaultRouterPort Setting this object will set the default router port for given VLAN.	column	Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.11`
wwpLeosMcastIgmpInquisitiveLeaveState Setting this object will set the IGMP inquisitive leave state for given VLAN.	column	Enumeration	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.12`
wwpLeosMcastIgmpLastMemberQueryInterval Setting this object will set the last membership query interval for given VLAN.	column	Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.13`
wwpLeosMcastIgmpPriority Setting this object will set the priority if IGMP packets for this VLAN.	column	Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.14`
wwpLeosMcastIgmpSnoopRouterRangeStartIpAddr The first IP Address of the router IP Address range.	column	SNMPv2-SMIIpAddress	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.15`
wwpLeosMcastIgmpSnoopRouterRangeEndIpAddr The last IP Address of the router IP Address range. When range is undefined, all leave/join messages will be forwarded to the router even when the multicast stream does not orig…	column	SNMPv2-SMIIpAddress	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.16`
wwpLeosMcastIgmpSnoopActiveLingerTimeout The object specifies the active linger timeout in seconds.	column	seconds Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.17`
wwpLeosMcastIgmpSnoopServerTopology The object specifies the server topology.	column	Enumeration	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.18`
wwpLeosMcastIgmpSnoopRapidRecoveryMode Specifies whether the rapid recovery mode is set to on or off. If this object is set to ON then device will generate and accept query packets with src IP = 0 else in the OFF stat…	column	Enumeration	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.19`
wwpLeosMcastIgmpSnoopRobustness The number of replies to send for each multicast group.	column	Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.2`
wwpLeosMcastIgmpSnoopProxyQueryInterval The interval period between each general query sent to the router. This parameter specifies how often to repeat the group specific query. Default will be 125 seconds. Note tha…	column	seconds Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.3`
wwpLeosMcastIgmpSnoopProxyQueryReplyTmo The amount of time to receive a membership report after a query message was sent. This value goes directly into the query packet.	column	seconds Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.4`
wwpLeosMcastIgmpSnoopLingerTmo This value specifies the amount of time that a multicast filter will be in place after the last host has left. In essence it configures how long to filter the stream after all …	column	seconds Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.6`
wwpLeosMcastIgmpQueryEngineState Setting this object to disable will enable query engine on a given VLAN. Setting it to enable will enable it.	column	Enumeration	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.7`
wwpLeosMcastIgmpProxyQuerySrcIp Setting this object will set the source ip address for the VLAN.	column	SNMPv2-SMIIpAddress	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.8`
wwpLeosMcastIgmpRouterQueryInterval Setting this object will set the router query interval for given VLAN.	column	Integer32	`.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.9`