wwpLeosMcastIgmpSnoopLingerTmo
WWP-LEOS-MULTICAST-FILTER-MIB ·
.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.6
Object
column
r/w
seconds Integer32
This value specifies the amount of time that a multicast filter will be in place after the last host has left. In essence it configures how long to filter the stream after all the hosts have left the group. This can tune the system as to how long the router has to remove the stream from the subnet. The minimum value is 1 second, with no maximum value.
Context
- MIB
- WWP-LEOS-MULTICAST-FILTER-MIB
- OID
.1.3.6.1.4.1.6141.2.60.7.1.1.4.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- wwpLeosMcastIgmpSnoopEntry
- Table
- wwpLeosMcastIgmpSnoopTable
- Siblings
- 18
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: 10-300
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wwpLeosMcastIgmpSnoopEnable For LEOS (4.x) IGMP snooping can be enabled on this
VLAN by setting this object to 'true'. The Management
station should define the router IP address range
and the list of server… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.1 |
| wwpLeosMcastIgmpMinResponseTime Setting this object will set the minimum response time for given VLAN. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.10 |
| wwpLeosMcastIgmpDefaultRouterPort Setting this object will set the default router port for given VLAN. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.11 |
| wwpLeosMcastIgmpInquisitiveLeaveState Setting this object will set the IGMP inquisitive leave state for given VLAN. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.12 |
| wwpLeosMcastIgmpLastMemberQueryInterval Setting this object will set the last membership query interval for given VLAN. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.13 |
| wwpLeosMcastIgmpPriority Setting this object will set the priority if IGMP packets
for this VLAN. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.14 |
| wwpLeosMcastIgmpSnoopRouterRangeStartIpAddr The first IP Address of the router IP Address range. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.15 |
| wwpLeosMcastIgmpSnoopRouterRangeEndIpAddr The last IP Address of the router IP Address range.
When range is undefined, all leave/join
messages will be forwarded to the router even when the
multicast stream does not orig… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.16 |
| wwpLeosMcastIgmpSnoopActiveLingerTimeout The object specifies the active linger timeout in seconds. | column | seconds Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.17 |
| wwpLeosMcastIgmpSnoopServerTopology The object specifies the server topology. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.18 |
| wwpLeosMcastIgmpSnoopRapidRecoveryMode Specifies whether the rapid recovery mode is set to on or off.
If this object is set to ON then device will generate and
accept query packets with src IP = 0 else in the OFF stat… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.19 |
| wwpLeosMcastIgmpSnoopRobustness The number of replies to send for
each multicast group. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.2 |
| wwpLeosMcastIgmpSnoopProxyQueryInterval The interval period between each general query
sent to the router. This parameter specifies how
often to repeat the group specific query.
Default will be 125 seconds. Note tha… | column | seconds Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.3 |
| wwpLeosMcastIgmpSnoopProxyQueryReplyTmo The amount of time to receive a membership
report after a query message was sent.
This value goes directly into the query packet. | column | seconds Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.4 |
| wwpLeosMcastIgmpSnoopProxyQueryDelay The amount of time to wait before sending the next
group specific query downstream.
General queries are sent one port at a time. | column | seconds Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.5 |
| wwpLeosMcastIgmpQueryEngineState Setting this object to disable will enable query engine on
a given VLAN. Setting it to enable will enable it. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.7 |
| wwpLeosMcastIgmpProxyQuerySrcIp Setting this object will set the source ip address for the VLAN. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.8 |
| wwpLeosMcastIgmpRouterQueryInterval Setting this object will set the router query interval for given VLAN. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.7.1.1.4.1.9 |