tmnxDot1agCfmMepFcltyInstance

TIMETRA-IEEE8021-CFM-MIB · .1.3.6.1.4.1.6527.3.1.2.52.9.3
Commands MIB view Table view

Object

scalar SNMPv2-TCDisplayString 
The value of tmnxDot1agCfmMepFcltyInstance indicates the specific
facility instance that a facility MEP has affected via a raised or
cleared event.
          
This value is used in combination with its tmnxDot1agCfmMepFcltyType.
          
The possible facility types and instance forms are described in the
following table:
          
      Facility Type         |  Facility Instance
    ---------------------------------------------
      port                  |  slot/mda/port
      lag                   |  lag-id
      networkInterface      |  interface name
      qinqPortTunnelSap     |  sap-id
      qinqLagTunnelSap      |  sap-id
          
The combined value will appear as in the following examples:
   port 7/2/2
   lag 1
   networkInterface test
   qinqPortTunnelSap 2/2/2:100.*
   qinqLagTunnelSap lag-1:100.*
          
 When a facility fault occurs on a QinQ port or lag, the sap executing
 the CFM functional test, the sap will be included as part of the
 event log message.  However, QinQ facility tunnel MEPs on the sap are
 only the detection point for the defect / clear condition.  The QinQ
 facility tunnel is port or lag based and a representative outer tag.

Context

MIB
TIMETRA-IEEE8021-CFM-MIB
OID
.1.3.6.1.4.1.6527.3.1.2.52.9.3
Type
scalar
Access
notifyonly
Status
current
Parent
tmnxDot1agCfmNotificationObjs
Groups
1

Net-SNMP examples

How SNMP and these commands work

Scalars have one instance, identified by the .0 suffix.

Read the scalar instance
/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'TIMETRA-IEEE8021-CFM-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-IEEE8021-CFM-MIB::tmnxDot1agCfmMepFcltyInstance.0'
More examples
Translate to a numeric OID
/usr/bin/snmptranslate -Pud -Ir -On -m 'TIMETRA-IEEE8021-CFM-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'TIMETRA-IEEE8021-CFM-MIB::tmnxDot1agCfmMepFcltyInstance'

Syntax

SNMPv2-TCDisplayString
Source
SNMPv2-TCDisplayString
Base type
OctetString
Display format
255a
Type Description
Represents textual information taken from the NVT ASCII
          
character set, as defined in pages 4, 10-11 of RFC 854.
          
To summarize RFC 854, the NVT ASCII repertoire specifies:
          
  - the use of character codes 0-127 (decimal)
          
  - the graphics characters (32-126) are interpreted as
    US ASCII
          
  - NUL, LF, CR, BEL, BS, HT, VT and FF have the special
    meanings specified in RFC 854
          
  - the other 25 codes have no standard interpretation
          
  - the sequence 'CR LF' means newline
          
  - the sequence 'CR NUL' means carriage-return
          
  - an 'LF' not preceded by a 'CR' means moving to the
    same column on the next line.
          
  - the sequence 'CR x' for any x other than LF or NUL is
    illegal.  (Note that this also means that a string may
    end with either 'CR LF' or 'CR NUL', but not with CR.)
          
Any object defined using this syntax may not exceed 255
characters in length.

Values & Constraints

Type Constraints
range: 0..255

Conformance

Member of
tmnxDot1agNotifyObjsGroupV14v0