sleAlarmSeverityIndex

The following alarms is devided by the specific character, ===============.
The division basis is that alarms is bounded or released.
              
001: portDown: To detect whether physical or logical interface's link status is up or down.
002: portUp: 
===============
003: portRemoved: To detect whether physical interface is installed or not.
004: portInstalled: 
===============
005: powerFail: To detect whether power module's operation status is good or not.
		(Without doubt, more than 1 power module should be equipped.)
006: powerOK: 
===============
007: powerRemoved: To detect whether power module is installed or not, through the PLD access.
		   (Without doubt, more than 1 power module should be equipped.)
008: powerInstalled: 
===============
009: fanFail: To detect whether FAN module's operation status is good or not.
010: fanOK: 
===============
011: fanRemoved: To detect whether FAN module is installed or not, through the PLD access.
012: fanInstalled: 
===============
013: moduleRemoved: To detect whether physical interface module is installed or not, through the S/W I2C
014: moduleInstalled: 
===============
015: systemRestart: Network system is restarted by operator. This is not H/W start but S/W start.
===============
016: systemStart: Network system is restarted by operator or system status. This is not S/W start but H/W start.
		  (This alarm isn??t used current)
===============
017: broadcastOver: To detect the receipt of broadcast packet.
 			    (This alarm isn??t used current)
018: broadcastUnder: 
===============
019: cpuOverLoad: To detect whether the configured CPU load threshold is less than current CPU load usage or not.
020: cpuUnderLoad: 
===============
021: memoryOverUsed: To detect whether the configured memory threshold is less than current memory usage or not.
022: memoryUnderUsed: 
===============
023: portOverThreshold: To detect whether the configured physical or logical interface threshold is 
			less than delta value of current interface's InOctects or not.
024: portUnderThreshold: 
===============
025: temperatureHigh: To detect whether the configured system's temperature threshold is 
		      less than current temperature or not.
026: temperatureLow: 
===============
027: mfgdBlocked: To detect whether the specific MAC by MAC flood guard is blocked or not.
028: mfgdReleased: 
===============
029: ipConflict: To detect whether the same IP address on different network node is configured or not.
030: ipUnconflict: 
===============
031: dhcpLeaseShortage: To detect whether IP address that can be assigned to subscriber by DHCP server is 
			sufficient or not.
032: dhcpLeaseSufficient: 
===============
033: dhcpOccuredIllegalEntry: To detect whether a subsceiber is using a static IP address or not.
034: dhcpRemovedIllegalEntry: 
===============
035: rmonAlarmRising: To detect whether rising threshold of a specific MO in RMON alarm sampling is 
		      less than current calculated value by alarm sample type or not. But alarm generation 
		      would be issued by means of event type in RMON event.
036: rmonAlarmNoRising: 
===============
037: rmonAlarmFalling: To detect whether falling threshold of a specific MO in RMON alarm sampling is 
		       less than current calculated value by alarm sample type or not. 
		       But alarm generation would be issued by means of event type in RMON event.
038: rmonAlarmNoFalling: 
===============
039: bpduGuardDisabled: To detect whether edge ports is guarded about superior BPDU or not. 
			In case of insertion edge node with 0 or lower priority than priority of current root bridge node, 
			it will be disarrangement during a short time because of recognition a new inserted node 
			as root bridge. 
			So these edge ports is guarded, and then edge ports is blocked about all superior BPDU. 
			So STP reconfiguration doesn't use this edge ports.
===============
040: rootGuardDisabled: To detect whether edge ports is guarded about superior BPDU or not. 
			In case of insertion edge node with 0 or lower priority than priority of current root bridge node, 
			it will be disarrangement during a short time because of recognition a new inserted node 
			as root bridge. 
			So, Root guard prevents a new inserted node from being root bridge as well as 
			receiving a superior BPDU from root bridge. 
			but this node participates in STP topology reconfiguration. 
			If root bridge does not send a superior BPDU, then this node acts usually though STP state change.
===============
041: portSecurity: To detect whether interface is configured for security or not. 
		   This can be used to prevent MAC from flooding as well as spoofing. 
		   That is, As a result, this will obstruct an attack as like DoS attack.
===============
042: userLogin: 
043: userLogout: 
===============
051: igmpGroupJoined: To detect whether a subscriber is joined a multicast group or not.
052: igmpGroupLeaved: 
===============
053: dhcpIpaddressBound: To detect wether a dynamic IP address is assigned to a subscriber or not.
054: dhcpIpaddressFree: 
===============
055: doorOpened: To detect whether outer door is opeded or not, as external alarm.
056: doorClosed: 
===============
057: powerModeChangedPowerToBattery: To detect whether a system is using AC power or battery. 
				     A system is using AC power usually. 
				     If there is any power problems as like a power failure, 
				     a system is using battery instead of AC power. 
058: powerModeChangedBatteryToPower: 
===============
059: batterylowcapacity: To detect whether current battery capacity is less 
			 capacity threshold according to battery usage or not. 
			 The capacity of AC power is 16 voltage and battery is 20. 
			 Capacity threshold is configured by H/W specification.
			 So operator can't change it.
060: batterynormalcapacity: 
===============
061: batteryhighTemperature: To detect whether current temperature of battery is greater than temperature threshold or not. 
062: batterynormalTemperature: 
===============
063: authenticationFail: To detect whether the connected user is authentic or non-authentic.
064: authenticationNofail: 
===============
065: psuAcHighTemperature: To detect whether current temperature of Power Supply Unit is 
			   greater than temperature threshold or not. 
066: psuAcNormalTemperature: 
===============
067: batteryRemoved: To detect whether battery is equipped at network system or not. 
		     Battery is used as redundancy power service. So operator can decide the installation of battery.
068: batteryEquipped: 
===============
069: batteryLowVoltage: To detect whether battery voltage is less than 12.5 volt or not. 
			12.5 volt value is configured by H/W specification. So operator can't change it.
070: batteryNormalVoltage: 
===============
071: adminAccessLogin: To detect whether a operator connects at this network system or not.
072: adminAccessLogout: 
===============
073: cfgdBlocked: To detect whether it is blocked flood to CPU or not.
074: cfgdReleased: 
===============
075: sfgdBlocked: To detect whether it is blocked flood to system or not.
076: sfgdReleased: 
===============
077: swWatchdogAbnormalState: To detect whether a specific process acts normally or not.
078: swWatchdogNormalState: 
===============
079: swWatchdogDetectError: To detect whether a specific process is detected a error related to itself or cleared.
080: swWatchdogClearError: 
===============
081: ppsControlBlocked: To detect whether it is blocked by pps-control or not.
082: ppsControlReleased: 
===============
083: gotDMITempHighOverAlarm: To detect whether internal temperature exceeds high alarm level or not.
084: gotDMITempHighFallAlarm: 
===============
085: gotDMITempLowOverAlarm: To detect whether internal temperature is below low alarm level or not.
086: gotDMITempLowFallAlarm: 
===============
087: gotDMITempHighOverWarning: To detect whether internal temperature exceeds high warning level or not.
088: gotDMITempHighFallWarning: 
===============
089: gotDMITempLowOverWarning: To detect whether internal temperature is below low warning level or not.
090: gotDMITempLowFallWarning: 
===============
091: gotDMIVolHighOverAlarm: To detect whether internal supply voltage exceeds high alarm level or not.
092: gotDMIVolHighFallAlarm: 
===============
093: gotDMIVolLowOverAlarm: To detect whether internal supply voltage is below low alarm level or not.
094: gotDMIVolLowFallAlarm: 
===============
095: gotDMIVolHighOverWarning: To detect whether internal supply voltage exceeds high warning level or not.
096: gotDMIVolHighFallWarning: 
===============
097: gotDMIVolLowOverWarning: To detect whether internal supply voltage is below low warning level or not.
098: gotDMIVolLowFallWarning: 
===============
099: gotDMITxBiasHighOverAlarm: To detect whether TX Bias current exceeds high alarm level or not.
100: gotDMITxBiasHighFallAlarm: 
===============
101: gotDMITxBiasLowOverAlarm: To detect whether TX Bias current is below low alarm level or not.
102: gotDMITxBiasLowFallAlarm: 
===============
103: gotDMITxBiasHighOverWarning: To detect whether TX Bias current exceeds high warning level or not.
104: gotDMITxBiasHighFallWarning: 
===============
105: gotDMITxBiasLowOverWarning: To detect whether TX Bias current is below low warning level or not.
106: gotDMITxBiasLowFallWarning: 
===============
107: gotDMITxPowerHighOverAlarm: To detect whether TX output power exceeds high alarm level or not.
108: gotDMITxPowerHighFallAlarm: 
===============
109: gotDMITxPowerLowOverAlarm: To detect whether TX output power is below low alarm level or not.
110: gotDMITxPowerLowFallAlarm: 
===============
111: gotDMITxPowerHighOverWarning: To detect whether TX output power exceeds high warning level or not.
112: gotDMITxPowerHighFallWarning: 
===============
113: gotDMITxPowerLowOverWarning: To detect whether TX output power is below low warning level or not.
114: gotDMITxPowerLowFallWarning: 
===============
115: gotDMIRxPowerHighOverAlarm: To detect whether RX output power exceeds high alarm level or not.
116: gotDMIRxPowerHighFallAlarm: 
===============
117: gotDMIRxPowerLowOverAlarm: To detect whether RX output power is below low alarm level or not.
118: gotDMIRxPowerLowFallAlarm: 
===============
119: gotDMIRxPowerHighOverWarning: To detect whether RX output power exceeds high warning level or not.
120: gotDMIRxPowerHighFallWarning: 
===============
121: gotDMIRxPowerLowOverWarning: To detect whether RX output power is below low warning level or not.
122: gotDMIRxPowerLowFallWarning: 
===============
123: nosRemoteUpgradeRequest: 
124: nosRemoteUpgradeSuccess: 
125: nosRemoteUpgradeFailAbort: 
126: nosRemoteUpgradeFailHeaderError: 
127: nosRemoteUpgradeFailDownloadError: 
128: nosRemoteUpgradeFailFlashError: 
129: nosRemoteUpgradeStart: 
===============
130: systemDyingGasp:
===============
133: cliHistory: To detect whether CLI history is detected or not.
134: cliHistoryNo:
===============
135: ntpConnectionFail: To detect whether NTP connection is failed or not.
136: ntpConnectionFailNo:
===============
137: nmsConnectionTypeChanged:  To detect whether NMS connection type is changed.
===============
159: clockModuleRemoved:  To detect whether clock module is removed or installed.
160: clockModuleInstalled:
161: clockModuleInitFail:  To detect whether clock module initiolization is failed or not.
162: clockModuleInitOk:
===============
163: cliHistoryLog: To detect whether CLI history log is over or not.
164: cliHistoryLogNo:
===============
165: slotActionEvent: To detect whether slot action is changed.
166: slotStateChange: To detect whether slot state is changed.
===============
167: interfaceAdminDown: To detect whether physical or logical interface's admin link status is up or down.
168: interfaceAdminUp:
===============
169: slotPowerMonAbnormal: To detect whether slot power monitor abnormal or normal is detected.
170: slotPowerMonNormal:
===============
171: slotErrorLEDChanged: To detect whether error LED is changed.
===============
185: cpuPpsOverThreshold: To detect whether PPS is over threshold or not.
186: cpuPpsUnderThreshold:
===============
199: slotHealthStatusTimeout: To detect whether slot health status is time out or not.
200: slotHealthStatusTimeoutCleared:
===============
201: advaTemperature: To detect whether current chassis temperature is less than chassis temperature threshold or not.
202: advaTemperatureNo: 
===============
203: advaPSUFailure: To detect whether ADVA system's power supply unit has a failure or not.
204: advaPSUFailureNo: 
===============
205: advaFanFailure: To detect whether ADVA system's FAN has a failure or not.
206: advaFanFailureNo: 
===============
207: advaInterfaceReceiveFailure: To detect whether ADVA system's receipt has a failure or not.
208: advaInterfaceReceiveFailureNo:  
===============
209: advaInterfaceOpticalThreshold: To detect whether Adva system's optical receive power level is 
				    less than optical threshold or not.
210: advaInterfaceOpticalThresholdNo: 
===============
211: advaInterfaceTransmitFault: To detect whether ADVA system's transmission has a failure or not.
212: advaInterfaceTransmitFaultNo: 
===============
213: dvaInterfaceMisconfiguration: To detect whether ADVA system's interface is configured rightly or not.
214: advaInterfaceMisconfigurationNo: 
===============
215: advaInterfaceSFPMismatch: To detect whether ADVA system's SFP interface is mismatched or not.
216: advaInterfaceSFPMismatchNo: 
===============
217: advaVoltageLow: To detect whether ADVA system's current voltage is less than voltage threshold or not.
218: advaVoltageLowNo: 
===============
219: advaVoltageHigh: To detect whether ADVA system's current voltage is greater than voltage threshold or not.
220: advaVoltageHighNo: 
===============
301: erpDomainLotp: To detect whether LOTP(Loss of Test Packet) exists a domain of ERP or not. 
		    The Loss of Test Packet defect is defined when a node does not receive 
		    any test packet at any of its ports for a period of 3 times.
302: erpDomainLotpNo: 
===============
303: erpDomainULotp: To detect whether undirectional LOTP(Loss of Test Packet) exists a domain of ERP or not. 
		     The Loss of Test Packet defect is defined when a RM node of one domain does not 
		     receive any test packet at one port for a period of 3 times.
304: erpDomainULotpNo: 
===============
305: erpDomainMultipleRM: To detect whether Multiple RM node is supported or not. 
			  The defect is raised when a RM node receives its own test packets 
			  with an Ack destination address field with a non-zero value.
306: erpDomainMultipleRMNo: 
===============
307: erpDomainRMNodeReacheablity: To detect whether RM reachability is raised or not. 
				  The detection of multiple failures indicates that the ring is segmented and 
			          that the RM Node is unreacheable. 
				  This is only possible at normal ring nodes isolated from the RM node.
308: erpDomainRMNodeReacheablityNo: 
===============
391: startupConfigLoadEnded: To detect whether startup configuration load is ended.
===============
401: eponOnuDeregister: To detect whether ONU is registered into OLT or not. 
			That is, ONU that its operation is service on should be sent registration information to OLT. 
402: eponOnuRegister: 
===============
403: eponOnuRegistrationError: To detect whether ONU is failed registeration process into OLT.
404: eponOnuNoRegistrationError: 
===============
405: eponBadEncryptionKey: To detect wwhether the encryption key is valid or not.
			   A message between ONU and OLT is encrypted using random encryption key. 
			   There is that the encryption key is invalid as transmission failure from time to time.
406: eponNoBadEncryptionKey: 
===============
407: eponLlidMistmatch: To detect whether Llid of message between ONU and OLT is valid or not. 
			On registering, ONU informs unique ID to OLT.
			And then, all communication between ONU and OLT must use the unique ID. 
			The unique ID is called Llid.
408: eponNoLlidMismatch: 
===============
409: eponTooManyRegister: To detect whether the registered ONU per 1 OLT is greater than 32 or not. 
			  That is, ONU can be registered from 1 to the maximum 32 at 1 OLT.
410: eponNoTooManyRegister: 
===============
411: eponDyingGASP: To detect whether a ONU is down from dying gasp or not. 
		    A ONU could be changed to down state as a number of reasons.
		    By the way, ONU that is changed to down as dying gasp would be sent dying gasp signal to OLT and 
		    then ONU's link would be changed to down.
412: eponNoDyingGASP: 
===============
413: eponOnuErrFramePeriod: 
414: eponOnuNoErrFramePeriod: 
===============
415: eponOnuErrFrame: 
416: eponOnuNoErrFrame: 
===============
417: eponOnuErrFrameSecondSummary: 
418: eponOnuNoErrFrameSecondSummary: 
===============
419: eponOnuLastOnuDeregister: To detect whether a deregistered ONU is last ONU or not. 
			       If a deregistered ONU is last ONU, the OLT would be changed to serviceable status. 
420: eponOnuNoLastOnuDeregister: 
===============
421: eponOltCableDown: 
422: eponOltRecoverCableDown: 
===============
501: autoCLIStart: To detect whether the scheduled auto CLI is started or not.
502: autoCLINoStart: 
===============
503: autoCLIComplete: To detect whether the scheduled auto CLI is completed or not. 
504: autoCLINoComplete: 
===============
505: autoCLIRemoveOutputFile: To detect whether the result file of the scheduled auto CLI is removed or not.
			      The reason that the result file is removed is that the configured file size for the result  is
			      less than the stored result file size. 
			      If so, the oldest file would be removed before everything.
506: autoCLINoRemoveOutputFile: 
===============
507: autoResetSystem: To detect whether the system is restarted or not. 
		      The conditions that system is restarted is that ping loss threshold is 
		      less than current ping loss count during the configured interval and 
		      that current free memory size is less than configured free memory size.
508: autoResetNoSystem: 
===============
509: autoResetPingReplyLoss: To detect whether ping reply from the designated network node is received or not.
			     Operator designates any gateway system that can communicate to detect 
			     current network environment. 
			     System sends ICMP packet to the designated gateway system periodically. 
			     If  the system doesn't receive ping reply packet within any interval, 
			     operator recognizes that the system can't communicate any more 
			     because of some problems of the system. 
510: autoResetNoPingReplyLoss: 
===============
511: autoResetMemoryLeakDetect: To detect whether current free memory size is 
				less than the configured free memory size or not. 
				Periodically, free memory size is checked to confirm system availability.
512: autoResetNoMemoryLeakDetect: 
===============
601: arulePacketDropDetect: To detect whether it is dropped some packet by arule or not.
602: arulePacketDropRelease: 
===============
620: bME1CardNoDetect: 
621: clearBME1CardNoDetect: 
===============
622: bME1CardAFEerror: 
623: clearBME1CardAFEerror: 
===============
624: bME1CardIFEerror: 
625: clearBME1CardIFEerror: 
===============
626: bME1CardFWerror: 
627: clearBME1CardFWerror: 
===============
628: bME1CardPROVerror: 
629: clearBME1CardPROVerror: 
===============
630: bME1CrashDetect: 
631: clearBME1CrashDetect: 
===============
632: bME2CardNoDetect: 
633: clearBME2CardNoDetect: 
===============
634: bME2CardAFEerror: 
635: clearBME2CardAFEerror: 
===============
636: bME2CardIFEerror: 
637: clearBME2CardIFEerror: 
===============
638: bME2CardFWerror: 
639: clearBME2CardFWerror: 
===============
640: bME2CardPROVerror: 
641: clearBME2CardPROVerror: 
===============
642: bME2CrashDetect: 
643: clearBME2CrashDetect: 
===============
644: bME3CardNoDetect: 
645: clearBME3CardNoDetect: 
===============
646: bME3CardAFEerror: 
647: clearBME3CardAFEerror: 
===============
648: bME3CardIFEerror: 
649: clearBME3CardIFEerror: 
===============
650: bME3CardFWerror: 
651: clearBME3CardFWerror: 
===============
652: bME3CardPROVerror: 
653: clearBME3CardPROVerror: 
===============
654: bME3CrashDetect: 
655: clearBME3CrashDetect: 
===============
656: powerFromBattery: 
657: clearPowerFromBattery: 
===============
658: invalidBatteryStatus: 
659: clearInvalidBatteryStatus: 
===============
660: batteryChargeLow: 
661: clearBatteryChargeLow: 
===============
662: batteryNotPresent: 
663: clearBatteryNotPresent: 
===============
664: voltageLow: 
665: clearVoltageLow: 
===============
666: tempOverThreshold: 
667: clearTempOverThreshold: 
===============
668: tempUnderThreshold: 
669: clearTempUnderThreshold: 
===============
670: cpuOverThreshold: 
671: clearCpuOverThreshold: 
===============
672: trafficOverload: 
673: clearTrafficOverload: 
===============
674: gEPONModuleNotDetect: 
675: clearGEPONModuleNotDetect:
===============
676: gEPONPortOperationDown: 
677: clearGEPONPortOperationDown: 
===============
678: gEPONNoIncomingTraffic: 
679: clearGEPONNoIncomingTraffic: 
===============
680: processCrashDetect: 
681: clearProcessCrashDetect: 
===============
682: memoryLeakDetect: 
683: clearMemoryLeakDetect: 
===============
684: memoryCorrupDetect: 
685: clearMemoryCorrupDetect: 
===============
686: memoryLowDetect: 
687: clearMemoryLowDetect: 
===============
688: dataLineerror: 
689: clearDataLineerror: 
===============
690: addressLineerror: 
691: clearAddressLineerror: 
===============
692: chipsetNotDetcet: 
693: clearChipsetNotDetcet: 
===============
694: pciBuserror: 
695: clearPciBuserror: 
===============
696: securityAdminConnect: 
697: clearSecurityAdminConnect: 
===============
698: oNUPowerDown: 
699: clearONUPowerDown: 
===============
700: oNUNotRegister: 
701: clearONUNotRegister: 
===============
702: oNTOpticPre: 
703: clearONTOpticPre: 
===============
800: switchoverInitiated: 
===============
801: switchoverDone: 
===============
803: redConfigurationMisMatch: To detect whether redundancy configuration is mismatched.
===============
901: gponNoAuthCBU: To detect no auth CBU is detected.
902: gponDuplicateONU: To detect ONU is duplicated.
903: gponDyingGasp: To detect dying GASP is detected.
904: gponUpgradeComplete: To detect upgrade complete is detected.
905: gponDeregistered: To detect whether deregistered is detected or not.
906: gponRegistered: 
907: gponRogueOnu: To detect rogue ONU is detected
908: gponOnuBatteryEvent: To detect whether ONU battery event is detected or not.
909: clearGponOnuBetteryEvent:
910: gponOnuPortOperStatus: To detectONU port operation statue is chagned.
911: gponTransceiverChanged: To detect transceiver is changed.
912: gponOltLosOn: To detect whether OLT LOS is on or off
913: gponOltLosOff:
914: gponOltLosiOn: To detect whether OLT LOSI is on or off
915: gponOltLosiOff:
916: gponDyingGaspOn: To detect whether dying GASP is on or off
917: gponDyingGaspOff:
918: gponOntOSUpgradeStatus: To detect ONT OS upgrade status is changed.
919: gponOntBLUpgradeStatus: To detect BL upgrade status is changed.
920: gponOltRxPowerLoss: To detect OLT RX power is loss.
921: gponOltRxPowerDetected: To detect OLT RX power status is changed.
922: gponOnuTemperatureHighOverThreshold: To detect whether ONU temperature exceeds high threshold or not.
923: gponOnuTemperatureHighFallThreshold:
924: gponOnuTemperatureLowOverThreshold: To detect whether ONU temperature belows low threshold or not.
925: gponOnuTemperatureLowFallThreshold:
926: gponOnuCpuOverThreshold: To detect whether ONU CPU exceeds threshold or not.
927: gponOnuCpuFallThreshold: 
928: gponOnuMemoryOverThreshold: To detect whether memory exceeds threshold or not.
929: gponOnuMemoryFallThreshold: 
930: gponOnuI2cFail: To detect ONU L2C fail is detected.
931: gponOnuRxOpticLowThreshAlarmOn: To detect whether ONU RX optic belows low threshold or not.
932: gponOnuRxOpticLowThreshAlarmOff: 
933: gponOnuRxOpticHighThreshAlarmOn: To detect whether ONU RX optic exceeds high threshold or not.
934: gponOnuRxOpticHighThreshAlarmOff:
935: gponOltLOFIOn: To detect whether OLT LOFL is on or off
936: gponOltLOFIOff:
937: gponOltDOWOn: To detect whether OLT DOW is on or off
938: gponOltDOWOff:
939: gponOltSFOn: To detect whether OLT SF is on or off
940: gponOltSFOff:
941: gponOltSDOn: To detect whether OLT SD is on or off
942: gponOltSDOff:
943: gponOltLCDGIOn: To detect whether OLT LCDGL is on or off
944: gponOltLCDGIOff:
945: gponOltRDOn: To detect whether OLT RD is on or off
946: gponOltRDOff:
947: gponOltSUFOn: To detect whether OLT SUF is on or off
948: gponOltSUFOff:
949: gponOltLOAOn: To detect whether OLT LOA is on or off
950: gponOltLOAOff:
951: gponOltLOAMIOn: To detect whether OLT LOAML is on or off
952: gponOltLOAMIOff:
953: gponOltMEMOn: To detect whether OLT MEM is on or off
954: gponOltMEMOff:
955: gponOltPEEOn: To detect whether OLT PEE is on or off
956: gponOltPEEOff:
957: gponOltPSTOn: To detect whether OLT PST is on or off
958: gponOltPSTOff:
959: gponOltERROn: To detect whether OLT ERR is on or off
960: gponOltERROff:
961: gponOltREIOn: To detect whether OLT REI is on or off
962: gponOltREIOff:
963: gponAntiSpoofingDupPortOn: To detect whether anti spoofing port is duplicated or not.
964: gponAntiSpoofingDupPortOff:
965: gponRedundancySwitchOver: To detect redundancy switchover is changed.
966: gponDuplicatedRangingResponse: To detect ranging response is changed.
967: gponOnuPortOpticModuleRemove: To detect whether ONU port optic module is removed or installed.
968: gponOnuPortOpticModuleInstall:
969: gponOnuOMCCProblemDetected: To detect whether ONU OMCC problem is detected or not.
970: gponOnuOMCCProblemCleared:
971: gponOltFixedTcontAlarmOn: To detect whether OLT fixed Tcont alarm is on or off.
972: gponOltFixedTcontAlarmOff:
973: gponOltDynamicTcontAlarmOn: To detect whether OLT dynamic Tcont alarm is on or off.
974: gponOltDynamicTcontAlarmOff:
975: gponOltPortCountAlarmOn: To detect whether OLT port count alarm is on or off.
976: gponOltPortCountAlarmOff:
977: gponOltCableDownAlarmOn: To detect whether OLT cable down alarm is on or off.
978: gponOltCableDownAlarmOff:
979: gponOltDeactiveMonitorAlarmOn: To detect whether deactive monitor alarm is on or off.
980: gponOltDeactiveMonitorAlarmOff:
981: gponOltDfiOn: To detect whether OLT DFI is on or off.
982: gponOltDfiOff:
984: gponOltTransceiverPortChanged: To detect OLT transeiver port is changed.
985: gponOnuPortOperStatusDown: To detect whether ONU port operation status is down or up.
986: gponOnuPortOperStatusUp::
===============
1101: emLogDefectCPUHighOver: To detect whether EM log detect CPU exceeds threshold or not.
1102: emLogDefectCPUHighUnder:
1103: emLogTemperHighOver: To detect whether EM log temperature exceeds high threshold or not.
1104: emLogTemperHighUnder:
1105: emLogTemperLowUnder: To detect whether EM log CPU belows low threshold or not.
1106: emLogTemperLowOver:
1107: emLogMemLowUnder:  To detect whether EM log memory belows low threshold or not.
1108: emLogMemLowOver:
1109: emLogFanFail:  To detect whether EM log fan status is failed or not.
1110: emLogFanFailCleared:
1111: emLogPhyCRCFail: To detect whether EM log physical CRC is failed or not.
1112: emLogPhyCRCFailCleared:
1113: emLogPhyDetectFail: To detect whether EM log physical status is failed or not.
1114: emLogPhyDetectFailCleared:
1115: emLogSFUMateInitFail: To detect whether EM log SFU mate initialization is failed or not.
1116: emLogSFUMateInitFailCleared:
1117: emLogDaemonHealthBad: To detect whether EM log daemon health is bad or not.
1118: emLogDaemonHealthBadCleared:
1119: emLogGPIURavenLinkDown: To detect whether EM log GPIU RAVEN link is down or not.
1120: emLogGPIURavenLinkDownCleared:
===============
1151: slotNosUpgradeStart: To detect whether slot NOS upgrade is started or ended.
1152: slotNosUpgradeEnd:
===============
1331: gponOnuAniVoltageLowThreshAlarmOn: To detect whether ONU ANI voltage belows low threshold or not.
1332: gponOnuAniVoltageLowThreshAlarmOff:
1333: gponOnuAniVoltageHighThreshAlarmOn: To detect whether ONU ANI voltage exceeds high threshold or not.
1334: gponOnuAniVoltageHighThreshAlarmOff:
1335: gponOnuAniTemperatureLowThreshAlarmOn: To detect whether ONU ANI temperature belows low threshold or not.
1336: gponOnuAniTemperatureLowThreshAlarmOff:
1337: gponOnuAniTemperatureHighThreshAlarmOn: To detect whether ONU ANI temperature exceeds high threshold or not.
1338: gponOnuAniTemperatureHighThreshAlarmOff:
1339: gponOnuAniTxBiasLowThreshAlarmOn: To detect whether ONU ANI TX bias belows low threshold or not.
1340: gponOnuAniTxBiasLowThreshAlarmOff:
1341: gponOnuAniTxBiasHighThreshAlarmOn: To detect whether ONU ANI TX bias exceeds high threshold or not. 
1342: gponOnuAniTxBiasHighThreshAlarmOff:
1343: gponOnuAniTxpowerLowThreshAlarmOn: To detect whether ONU ANI TX power belows low threshold or not.
1344: gponOnuAniTxpowerLowThreshAlarmOff:
1345: gponOnuAniTxpowerHighThreshAlarmOn: To detect whether ONU ANI TX power exceeds high threshold or not.
1346: gponOnuAniTxpowerHighThreshAlarmOff:

MIB

SLE-FAULTMGMT-MIB

OID

.1.3.6.1.4.1.6296.101.4.2.1.1.1

Type

column

Access

readonly

Status

current

Parent

sleAlarmSeverityEntry

Groups

1