spsActiveAlarmTypeId
SILVERPEAK-MGMT-MIB ·
.1.3.6.1.4.1.23867.3.1.1.2.1.1.13
Object
column
Integer32
An ID that uniquely identifies a type of alarm.
The following is a list of currently defined type IDs
(ID listed below is in hexadecimal):
ID Description
----- ------------------------------------------
10000 Tunnel remote ID is misconfigured
10001 Tunnel state is Down
10002 Tunnel VRRP IP is misconfigured
10003 Tunnel keepalive version mismatch
10004 Tunnel WCCP GID is misconfigured
10005 Tunnel software version mismatch
10006 Connecting to a non-VX-X is not supported.
Please contact sales@silver-peak.com to discuss your options.
10007 Duplicate Silver Peak license detected on peer device.
10008 Tunnel local IP address not owned by this appliance
10009 Tunnel software version mismatch results in reduced functionality.
1000a Tunnel peer encapsulation mode mismatch detected.
1000b UDP Destination Port is the same as flow redirection port
20000 Tunnel has unexpected traffic class error
30000 RAID array is degraded
30001 Disk is failed
30002 Disk is degraded
30003 Fan failure detected
30004 System bypass mode
30005 LAN/WAN fail-to-wire card failure
30006 LAN/WAN fail-to-wire card relay failure
30007 Encryption card hardware failure
30008 Network interface admin down
30009 Network interface link down
3000a Management interface link down
3000b Interface is half duplex
3000c Interface speed is 10 Mbps
3000d Config DB disk full
3000e Operating System disk full
3000f File system disk full
30010 Datapath internal loopback test failed
30011 WAN next-hop unreachable
30012 VRRP instance is down
30013 VRRP state changed from Master to Backup
30014 WAN next-hop router discovered on a LAN port
(box is in backwards)
30015 Disk is not in service
30016 Disk is rebuilding
30017 Disk removed by operator
30018 LAN/WAN interfaces have different admin states
30019 LAN/WAN interfaces have different link carrier states
3001a LAN/WAN interface has been shutdown due to
link propagation of paired interface
3001b Disk SMART threshold exceeded
3001c Flow redirection cluster peer is down
3001d Bonding members have different speed/duplex
3001e WCCP adjacency(ies) down
3001f WCCP assignment table mismatch
30020 Power supply not connected, not powered or failed
30021 NIC interface failure
30022 LAN next-hop unreachable
30023 Unexpected system restart
30024 Insufficient configured memory size for this virtual appliance
30025 Insufficient configured processor count for this virtual appliance
30026 Insufficient configured disk storage for this virtual appliance
30027 Interfaces have different MTUs
30028 Interfaces have different MTUs
30029 Bridge loop is detected
3002a Bridge creation failed
3002b Network interface is unassigned
3002c System optimization turned off
3002d Sub-optimal configured memory size for this virtual appliance
3002e Sub-optimal configured processor count for this virtual appliance
3002f Sub-optimal configured disk storage for this virtual appliance
40000 Software upgrade process has failed
40001 System is low on resources
40002 Significant change in time of day has occurred,
and might compromise statistics.
40003 The licensing for this virtual appliance has expired.
40004 There is no license installed on this virtual appliance.
40005 A disk self test has been performed. The system will
require a reboot after the test.
40006 The SSL private key is invalid.
40007 The SSL certificate is not yet valid.
40008 The SSL certificate has expired.
40009 The NTP server is unreachable.
4000a Virtual appliance license expires on yyyy/mm/dd.
4000b Virtual appliance license expires on yyyy/mm/dd.
4000c Invalid virtual appliance license.
4000d Dual Wan-nexthop topology configuration no longer supported.
4000e Setting system wan-nexthop to VLAN nhop is no longer necessary.
4000f Minor inconsistencies during QOS upgrade.
40010 Major inconsistencies during QOS upgrade.
40011 Tunnel IP hdr disable setting was discarded during upgrade.
40012 A very large range has been configured for a local subnet.
40013 A peer name has been specified in a route-map that can't be resolved.
40014 Shaper max bandwidth exceeds system bandwidth
40015 Software capability token exceeds warning threshold
40016 Software capability token has exceeded the required limit
40017 Silvepeak Portal is unreachable
40018 Silverpeak Portal is unreachable for setting up a remote help session
40019 An application has been deleted on the Silver Peak portal
4001a Boost Limiting MTS
4001b Bad portal registration data
4001c EdgeConnect Base license not granted
4001d Orchestrator is unreachable from appliance using HTTPS
4001e Silver Peak Portal is unreachable for licensing
4001f Silver Peak Portal hostname cannot be resolved
40020 Edge Connect Plus license not granted
40021 Edge Connect Boost license not granted
40022 Appliance has not been approved for licensing by Orchestrator
40023 Software capability token related alarm
40024 A NATed interface connected to Internet has no public IP address
40025 Initial admin password is not yet changed
40026 DHCP server mis-configuration
40027 Subnet table has exceeded high-water level for BGP/OSPF entries
40028 Subnet table has reached maximum capacity
40029 Unable to resolve Orchestrator DNS name
4002a Builtin CA certificate is not valid
4002b CA certificate Bundle is not valid
4002c A BGP peer session is no longer in Established state
4002d An IP SLA monitor is in Down state
4002e An OSPF neighbor session is no longer in Full state
4002f DNS Proxy is down
40030 EC Licensing Warning
40031 DHCP server failover my state communications interrupted
40032 Secure Shell challenge-response passed
40033 Secure Shell challenge-response failed
40034 An IP SLA monitor is not installed
40035 Excessive route advertisement updates detected
40036 CPU uilization threshold exceeded
40037 DSCP label is unassigned
40038 Peer interface admin or oper or nh reachability is down
40039 EC Feature License not granted
4003a Stats collection slow or incomplete
4003b Unable to resolve Stats Collector DNS name
4003c Stats Collector is unreachable
4003d Failed to process ACL group template/data file
4003e ACL group string store memory exceeded
4003f ACL rule contains invalid syntax
40040 Failed to process AVC attribute template/data file
40041 Failed to register with the Cloud Portal using the credentials provided
40042 Failed to register with the Cloud Portal due to a network issue
40043 Failed to register with the Cloud Portal due to database errors
40044 BFD process is unresponsive
40045 Failed to load config DB
40046 Maximum allowable OSPF neighbors exceeded
40047 A bonded LACP port is in Down state
40048 A bonded LACP aggregator is in Down state
50001 WAN-side transmit throughput TCA
50002 LAN-side receive throughput TCA
50003 Total number of optimized flows TCA
50004 Total number of flows TCA
50005 File-system utilization TCA
50006 Tunnel latency TCA
50007 Tunnel loss pre-FEC TCA
50008 Tunnel loss post-FEC TCA
50009 Tunnel OOP pre-POC TCA
5000a Tunnel OOP post-POC TCA
5000b Tunnel utilization TCA
5000c Tunnel reduction TCA
5000d Appliance capacity TCA
----- ------------------------------------------
Context
- MIB
- SILVERPEAK-MGMT-MIB
- OID
.1.3.6.1.4.1.23867.3.1.1.2.1.1.13- Type
- column
- Access
- readonly
- Status
- current
- Parent
- activeAlarmEntry
- Table
- spsActiveAlarmTable
- Siblings
- 12
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| spsActiveAlarmIndex An index that uniquely identifies an entry in the
active alarm table. | column | Integer32 | .1.3.6.1.4.1.23867.3.1.1.2.1.1.1 |
| spsActiveAlarmClearable Identifies if the user can manually clear the alarm. | column | SILVERPEAK-TCSilverpeakYesNo | .1.3.6.1.4.1.23867.3.1.1.2.1.1.10 |
| spsActiveAlarmLogTime The value of sysUpTime when the alarm was generated. | column | OctetString | .1.3.6.1.4.1.23867.3.1.1.2.1.1.11 |
| spsActiveAlarmServiceAffect Identifies if the alarm is service affecting. | column | SILVERPEAK-TCSilverpeakYesNo | .1.3.6.1.4.1.23867.3.1.1.2.1.1.12 |
| spsActiveAlarmSeqNum The active alarm's sequence number at the time it was generated. | column | SILVERPEAK-TCSilverpeakSeqNum | .1.3.6.1.4.1.23867.3.1.1.2.1.1.2 |
| spsActiveAlarmSeverity The alarm severity for the active alarm. | column | SILVERPEAK-TCSilverpeakAlarmSeverity | .1.3.6.1.4.1.23867.3.1.1.2.1.1.3 |
| spsActiveAlarmName A short name for the active alarm. | column | OctetString | .1.3.6.1.4.1.23867.3.1.1.2.1.1.4 |
| spsActiveAlarmDescr A description for the active alarm. | column | OctetString | .1.3.6.1.4.1.23867.3.1.1.2.1.1.5 |
| spsActiveAlarmSource The source for the active alarm. | column | OctetString | .1.3.6.1.4.1.23867.3.1.1.2.1.1.6 |
| spsActiveAlarmType The alarm type for the active alarm. | column | OctetString | .1.3.6.1.4.1.23867.3.1.1.2.1.1.7 |
| spsActiveAlarmAcked Identifies if the user has acknowledged the alarm. | column | SILVERPEAK-TCSilverpeakYesNo | .1.3.6.1.4.1.23867.3.1.1.2.1.1.8 |
| spsActiveAlarmActive Identifies if the alarm is currently active. | column | SILVERPEAK-TCSilverpeakYesNo | .1.3.6.1.4.1.23867.3.1.1.2.1.1.9 |