ruckusIpv6AclFilterStdProtocol

RUCKUS-ACL-MIB · .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.3
MIB view Table view

Object

column r/w Enumeration 
Standard transport protocols allowed. The extended option 
enables to define other protocol using the OID
ruckusIpv6AclFilterExtProtocol which takes any value.

Context

MIB
RUCKUS-ACL-MIB
OID
.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.3
Type
column
Access
readwrite
Status
current
Parent
ruckusIpv6AclFilterEntry
Table
ruckusIpv6AclFilterTable
Siblings
29

Syntax

Enumeration

Values & Constraints

Enumerated Values
6tcp
17udp
41ip6
50esp
51ahp
58icmp
132sctp
255extended

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
ruckusIpv6AclFilterSeqNum
Specifies the sequence number for this ACL filter.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.1
ruckusIpv6AclFilterDestAddr
Destination Ipv6 address to match in packets.
columnINET-ADDRESS-MIBInetAddressIPv6.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.10
ruckusIpv6AclFilterDestPrefixLen
Destination Ipv6 address prefix length.
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.11
ruckusIpv6AclFilterDestOperator
Type of comparison to perform. For now, this only applies to TCP/UDP for comparing the port number.
columnAclOperator.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.12
ruckusIpv6AclFilterDestPortLow
Specifies the TCP/UDP port number to match in packets. If the operator is 'range', it specfies the start of range.
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.13
ruckusIpv6AclFilterDestPortHigh
Used only if the operator is defined as 'range', where it specifies the end of range
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.14
ruckusIpv6AclFilterEstablished
Enable/Disable the filtering of established TCP packets of which the ACK or RESET flag is on. This filter only applies to TCP transport protocol.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.15
ruckusIpv6AclFilterIcmpType
Specifies the ICMP6 type for matching if the Protocol is ICMP6. 0 means ignore the field.
columnEnumeration.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.16
ruckusIpv6AclFilterIcmpCode
ICMP Message Code value. Used in combination with ICMP Message Type to setup an ICMP filter. This object is not used with any other protocol. 0 means ignored. The supported values…
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.17
ruckusIpv6AclFilterExtIcmpType
Any type that can't be specified using the standard types can be specified using this object.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.18
ruckusIpv6AclFilterPolicyName
Specifies the DSCP value to use in matching or marking.
columnAclPolicyName.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.19
ruckusIpv6AclFilterAction
Action to take if the IPv6 packet matches with this access control list filter.
columnAclAction.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.2
ruckusIpv6AclFilterDscpMatch
Specifies the DSCP value for matching with this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.20
ruckusIpv6AclFilterDscpForce
Specifies the DSCP value to be used for marking in outgoing packets matching this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.21
ruckusIpv6AclFilterPriorityMatch
Specifies the 802.1P priority for matching with this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.22
ruckusIpv6AclFilterPriorityForce
Specifies the 802.1P priority to be used for marking in outgoing packets matching this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.23
ruckusIpv6AclFilterInternalPriority
QoS priority option for this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.24
ruckusIpv6AclFilterFragments
Match IPv6 fragments with non-zero fragment offset in V6 packets matching this ACL permit clause.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.25
ruckusIpv6AclFilterSourceRoute
Match only rource routed packets matching this ACL permit clause.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.26
ruckusIpv6AclFilterMirrorPkts
Mirror packets matching ACL permit clause.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.27
ruckusIpv6AclFilterLogEnable
Specifies if logging is enabled for the filter.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.28
ruckusIpv6AclFilterComments
Remark description of individual Access Control List entry.
columnOctetString.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.29
ruckusIpv6AclFilterRowStatus
The row status variable, used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the creation of IPv6 ACL filt…
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.30
ruckusIpv6AclFilterExtProtocol
Any transport protocol other than standard protocols mentioned with ruckusIpv6AclFilterStdProtocol OID. 0 means any protocol.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.4
ruckusIpv6AclFilterSrcAddr
Source Ipv6 address to match in packets.
columnINET-ADDRESS-MIBInetAddressIPv6.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.5
ruckusIpv6AclFilterSrcPrefixLen
Source Ipv6 address prefix length.
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.6
ruckusIpv6AclFilterSrcOperator
Type of comparison to perform. For now, this only applies to TCP/UDP for comparing the port number.
columnAclOperator.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.7
ruckusIpv6AclFilterSrcPortLow
Specifies the TCP/UDP port number to match in packets. If the operator is 'range', it specfies the start of range.
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.8
ruckusIpv6AclFilterSrcPortHigh
Used only if the operator is defined as 'range', where it specifies the end of range
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.9