ruckusIpv6AclFilterComments
RUCKUS-ACL-MIB ·
.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.29
Object
column
OctetString
Remark description of individual Access Control List entry.
Context
- MIB
- RUCKUS-ACL-MIB
- OID
.1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.29- Type
- column
- Access
- readonly
- Status
- current
- Parent
- ruckusIpv6AclFilterEntry
- Table
- ruckusIpv6AclFilterTable
- Siblings
- 29
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ruckusIpv6AclFilterSeqNum Specifies the sequence number for this ACL filter. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.1 |
| ruckusIpv6AclFilterDestAddr Destination Ipv6 address to match in packets. | column | INET-ADDRESS-MIBInetAddressIPv6 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.10 |
| ruckusIpv6AclFilterDestPrefixLen Destination Ipv6 address prefix length. | column | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.11 |
| ruckusIpv6AclFilterDestOperator Type of comparison to perform. For now, this only
applies to TCP/UDP for comparing the port number. | column | AclOperator | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.12 |
| ruckusIpv6AclFilterDestPortLow Specifies the TCP/UDP port number to match in packets.
If the operator is 'range', it specfies the start of range. | column | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.13 |
| ruckusIpv6AclFilterDestPortHigh Used only if the operator is defined as 'range', where it
specifies the end of range | column | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.14 |
| ruckusIpv6AclFilterEstablished Enable/Disable the filtering of established TCP packets
of which the ACK or RESET flag is on. This filter only
applies to TCP transport protocol. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.15 |
| ruckusIpv6AclFilterIcmpType Specifies the ICMP6 type for matching if the Protocol is ICMP6.
0 means ignore the field. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.16 |
| ruckusIpv6AclFilterIcmpCode ICMP Message Code value. Used in combination with ICMP Message
Type to setup an ICMP filter. This object is not used with any
other protocol. 0 means ignored. The supported values… | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.17 |
| ruckusIpv6AclFilterExtIcmpType Any type that can't be specified using the standard types
can be specified using this object. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.18 |
| ruckusIpv6AclFilterPolicyName Specifies the DSCP value to use in matching or marking. | column | AclPolicyName | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.19 |
| ruckusIpv6AclFilterAction Action to take if the IPv6 packet matches with this
access control list filter. | column | AclAction | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.2 |
| ruckusIpv6AclFilterDscpMatch Specifies the DSCP value for matching with this filter. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.20 |
| ruckusIpv6AclFilterDscpForce Specifies the DSCP value to be used for marking in outgoing
packets matching this filter. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.21 |
| ruckusIpv6AclFilterPriorityMatch Specifies the 802.1P priority for matching with this filter. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.22 |
| ruckusIpv6AclFilterPriorityForce Specifies the 802.1P priority to be used for marking in outgoing
packets matching this filter. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.23 |
| ruckusIpv6AclFilterInternalPriority QoS priority option for this filter. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.24 |
| ruckusIpv6AclFilterFragments Match IPv6 fragments with non-zero fragment offset in V6 packets
matching this ACL permit clause. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.25 |
| ruckusIpv6AclFilterSourceRoute Match only rource routed packets matching this ACL permit clause. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.26 |
| ruckusIpv6AclFilterMirrorPkts Mirror packets matching ACL permit clause. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.27 |
| ruckusIpv6AclFilterLogEnable Specifies if logging is enabled for the filter. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.28 |
| ruckusIpv6AclFilterStdProtocol Standard transport protocols allowed. The extended option
enables to define other protocol using the OID
ruckusIpv6AclFilterExtProtocol which takes any value. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.3 |
| ruckusIpv6AclFilterRowStatus The row status variable, used according to installation and
removal conventions for conceptual rows. Setting this object
to createAndGo(4) results in the creation of IPv6 ACL filt… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.30 |
| ruckusIpv6AclFilterExtProtocol Any transport protocol other than standard protocols mentioned
with ruckusIpv6AclFilterStdProtocol OID. 0 means any protocol. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.4 |
| ruckusIpv6AclFilterSrcAddr Source Ipv6 address to match in packets. | column | INET-ADDRESS-MIBInetAddressIPv6 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.5 |
| ruckusIpv6AclFilterSrcPrefixLen Source Ipv6 address prefix length. | column | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.6 |
| ruckusIpv6AclFilterSrcOperator Type of comparison to perform. For now, this only
applies to TCP/UDP for comparing the port number. | column | AclOperator | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.7 |
| ruckusIpv6AclFilterSrcPortLow Specifies the TCP/UDP port number to match in packets.
If the operator is 'range', it specfies the start of range. | column | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.8 |
| ruckusIpv6AclFilterSrcPortHigh Used only if the operator is defined as 'range', where it
specifies the end of range | column | Unsigned32 | .1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.9 |