ruckusIpv4AclFilterDestPortHigh

RUCKUS-ACL-MIB · .1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.14
MIB view Table view

Object

column r/w Unsigned32 
Used only if the operator is defined as 'range', where it
specifies the end of range

Context

MIB
RUCKUS-ACL-MIB
OID
.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.14
Type
column
Access
readwrite
Status
current
Parent
ruckusIpv4AclFilterEntry
Table
ruckusIpv4AclFilterTable
Siblings
29

Syntax

Unsigned32

Values & Constraints

Object Constraints
range: 0-65535

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
ruckusIpv4AclFilterSeqNum
Specifies the sequence number for this ACL filter.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.1
ruckusIpv4AclFilterDestAddr
Destination Ipv4 address to match in packets.
columnINET-ADDRESS-MIBInetAddressIPv4.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.10
ruckusIpv4AclFilterDestMask
Destination Ipv4 address mask used in combination with source IPv4 address to derive effective address for matching.
columnINET-ADDRESS-MIBInetAddressIPv4.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.11
ruckusIpv4AclFilterDestOperator
Type of comparison to perform. For now, this only applies to TCP/UDP for comparing the port number.
columnAclOperator.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.12
ruckusIpv4AclFilterDestPortLow
Specifies the TCP/UDP port number to match in packets. If the operator is 'range', it specfies the start of range.
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.13
ruckusIpv4AclFilterEstablished
Enable/Disable the filtering of established TCP packets of which the ACK or RESET flag is on. This filter only applies to TCP transport protocol.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.15
ruckusIpv4AclFilterPrecedence
Specifies the IP precedence value to match in packets.
columnIpPrecedence.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.16
ruckusIpv4AclFilterTos
This refers to the IP TOS value in range <0-15>, which is the sum of numeric vlaues of the following options 0x0 - normal TOS 0x1 - minimum monetary cost TOS 0x2 - maximum reliabi…
columnIpTos.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.17
ruckusIpv4AclFilterIcmpType
Specifies the ICMP type for matching if the Protocol is ICMP. 0 means ignore the field.
columnEnumeration.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.18
ruckusIpv4AclFilterIcmpCode
ICMP Message Code value. Used in combination with ICMP Message Type to setup an ICMP filter. This object is not used with any other protocol. 0 means ignored. The supported values…
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.19
ruckusIpv4AclFilterAction
Action to take if the IP packet matches with this ACL filter.
columnAclAction.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.2
ruckusIpv4AclFilterExtIcmpType
Any type that can't be specified using the standard types can be specified using this object.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.20
ruckusIpv4AclFilterPolicyName
Specifies the DSCP value to use in matching or marking.
columnAclPolicyName.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.21
ruckusIpv4AclFilterDscpMatch
Specifies the DSCP value for matching with this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.22
ruckusIpv4AclFilterDscpForce
Specifies the DSCP value to be used for marking in outgoing packets matching this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.23
ruckusIpv4AclFilterPriorityMatch
Specifies the 802.1P priority for matching with this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.24
ruckusIpv4AclFilterPriorityForce
Specifies the 802.1P priority to be used for marking in outgoing packets matching this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.25
ruckusIpv4AclFilterInternalPriority
QoS priority option for this filter.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.26
ruckusIpv4AclFilterMirrorPkts
Mirror packets matching ACL permit clause.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.27
ruckusIpv4AclFilterLogEnable
Specifies if logging is enabled for the filter.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.28
ruckusIpv4AclFilterComments
Remark description of individual Access Control List entry.
columnOctetString.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.29
ruckusIpv4AclFilterStdProtocol
Standard transport protocols allowed. The extended option enables to define other protocol using the OID ruckusIpv4AclFilterExtProtocol which takes any value.
columnEnumeration.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.3
ruckusIpv4AclFilterRowStatus
The row status variable, used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the creation of IPv4 ACL filt…
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.30
ruckusIpv4AclFilterExtProtocol
Any transport protocol other than standard protocols mentioned with ruckusIpv4AclFilterStdProtocol OID. 0 means any protocol.
columnInteger32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.4
ruckusIpv4AclFilterSrcAddr
Source Ipv4 address to match in packets.
columnINET-ADDRESS-MIBInetAddressIPv4.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.5
ruckusIpv4AclFilterSrcMask
Source Ipv4 address mask used in combination with source IPv4 address to derive effective address for matching.
columnINET-ADDRESS-MIBInetAddressIPv4.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.6
ruckusIpv4AclFilterSrcOperator
Type of comparison to perform. For now, this only applies to TCP/UDP for comparing the port number.
columnAclOperator.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.7
ruckusIpv4AclFilterSrcPortLow
Specifies the TCP/UDP port number to match in packets. If the operator is 'range', it specfies the start of range.
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.8
ruckusIpv4AclFilterSrcPortHigh
Used only if the operator is defined as 'range', where it specifies the end of range
columnUnsigned32.1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1.9