pwTDMCfgSetUp2SynchTimeOut
PW-TDM-MIB ·
.1.3.6.1.2.1.186.1.3.1.11
Object
The amount of time the host should wait before declaring the pseudowire in a down state, if the number of consecutive TDM packets that have been received after changing the administrative status to up and after finalization of signaling (if supported) between the two PEs is smaller than pwTDMCfgConsecPktsInSynch. Once the PW has OperStatus of 'up', this parameter is no longer valid. This parameter is defined to ensure that the host does not prematurely inform failure of the PW. In particular, PW 'down' notifications should not be sent before expiration of this timer. This parameter is valid only after administrative changes of the status of the PW. If the PW fails due to network impairments, a 'down' notification should be sent. Object MAY be changed only when the related PW is defined as not active.
Context
- MIB
- PW-TDM-MIB
- OID
.1.3.6.1.2.1.186.1.3.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Units
- millisecond
- Parent
- pwTDMCfgEntry
- Table
- pwTDMCfgTable
- Siblings
- 19
Syntax
millisecond SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pwTDMCfgIndex Index to an entry in this table. When an NMS creates
a new entry/row in this table, it best makes use of
the value of the pwTDMCfgIndexNext object in order to
find a free or avai… | column | PwTDMCfgIndex | .1.3.6.1.2.1.186.1.3.1.1 |
| pwTDMCfgConsecMissPktsOutSynch The number of consecutive missing packets that are
required to enter the LOPS.
Object MAY be changed only when the related PW is
defined as not active. | column | Unsigned32 | .1.3.6.1.2.1.186.1.3.1.10 |
| pwTDMCfgPktReplacePolicy This parameter determines the value to be played when CE bound
packets over/underflow the jitter buffer, or are missing
for any reason. This byte pattern is sent (played) on
the … | column | Enumeration | .1.3.6.1.2.1.186.1.3.1.12 |
| pwTDMCfgAvePktLossTimeWindow The length of time over which the average packet
loss rate should be computed to detect excessive packet
loss rate.
Object MAY be changed only when the related PW is
defined as no… | column | millisecond SNMPv2-SMIInteger32 | .1.3.6.1.2.1.186.1.3.1.13 |
| pwTDMCfgExcessivePktLossThreshold Excessive packet loss rate is detected by computing the
average packet-loss rate over a pwTDMCfgAvePktLossTimeWindow
amount of time and comparing it with this threshold value.
The… | column | Percent SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.186.1.3.1.14 |
| pwTDMCfgAlarmThreshold Alarms are only reported when the defect state persists
for the length of time specified by this object.
Object MAY be changed only when the related PW is
defined as not active. | column | milisec SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.186.1.3.1.15 |
| pwTDMCfgClearAlarmThreshold Alarm MUST be cleared after the corresponding defect is
undetected for the amount of time specified by this object.
Object MAY be changed only when the related PW is
defined as no… | column | milisec SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.186.1.3.1.16 |
| pwTDMCfgMissingPktsToSes Percent of missing packets detected (consecutive or not)
within a 1-second window to cause a Severely Error
Second (SES) to be counted.
Object MAY be changed only when the related… | column | Percent SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.186.1.3.1.17 |
| pwTDMCfgTimestampMode Timestamp generation MAY be used in one of the following
modes:
1. Absolute mode: The PSN-bound IWF sets timestamps
using the clock recovered from the incoming TDM attachment
ci… | column | Enumeration | .1.3.6.1.2.1.186.1.3.1.18 |
| pwTDMCfgStorageType This variable indicates the storage type for this
row. Conceptual rows having the value permanent(4) must
allow write-access to all columnar objects. | column | SNMPv2-TCStorageType | .1.3.6.1.2.1.186.1.3.1.19 |
| pwTDMCfgRowStatus Object used for creating, modifying, and deleting
a row from this table. The following objects cannot be
modified if the entry is in use and the status is active:
pwTDMCfgPayload… | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.186.1.3.1.2 |
| pwTDMCfgPktFiller Filler byte pattern played out on the TDM
interface if pwTDMCfgPktReplacePolicy
was set to filler(3).
Object MAY be changed only when the related PW is
defined as not active. | column | Unsigned32 | .1.3.6.1.2.1.186.1.3.1.20 |
| pwTDMCfgName A descriptive string, preferably a unique name, to an entry
in this table.
Object MAY be changed at any time. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.2.1.186.1.3.1.21 |
| pwTDMCfgPayloadSize The value of this object indicates the PayLoad Size (in bytes)
to be defined during the PW setUp. Upon TX, implementation
must be capable of carrying that amount of bytes.
Upon R… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.186.1.3.1.4 |
| pwTDMCfgPktReorder If set to True: as CE-bound packets are queued in the
jitter buffer, out of order packets are re-ordered. The
maximum sequence number differential (i.e., the range in
which re-se… | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.186.1.3.1.5 |
| pwTDMCfgRtpHdrUsed If set to False: an RTP header is not pre-pended to the
TDM packet. | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.186.1.3.1.6 |
| pwTDMCfgJtrBfrDepth The size of this buffer SHOULD be locally
configured to allow accommodation to the PSN-specific packet
delay variation.
If configured to a value not supported by th… | column | microsecond SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.186.1.3.1.7 |
| pwTDMCfgPayloadSuppression Selecting 'enable' means: Payload suppression is allowed.
Payload MAY be omitted in order to conserve bandwidth.
Selecting 'disable' means: No suppression under any
condition.
Obj… | column | Enumeration | .1.3.6.1.2.1.186.1.3.1.8 |
| pwTDMCfgConsecPktsInSynch The number of consecutive packets with sequential
sequence numbers that are required to exit the
LOPS.
Object MAY be changed only when the related PW is
defined as not active. | column | Unsigned32 | .1.3.6.1.2.1.186.1.3.1.9 |