fxsReversalOnIdleEnable
MX-FXS-MIB ·
.1.3.6.1.4.1.4935.15.40.1.125
Object
This object is deprecated. Therefore, agents may or may not implement it.
Use fxsPolarityAndDenialBehavior instead.
The Reversal on Idle feature is used because of an inability by some
customer's CPE to react to busy tone. This problem can be overcome by
applying polarity reversal when the circuit is not busy . The reversal
allows the CPE to effect release of a circuit under line lockout conditions
or the other party clearing. When a customer's line is in the idle, line
lockout or blocked state, the polarity of the customer's line is reversed.
When the customer's line is seized to originate a call, or ring current is
applied to terminate a call, the line polarity is returned to normal.
On release, line polarity is returned to the reversed condition.
When activated, this feature replaces the default behaviour of the unit
which is to briefly remove power from the line to signal that the remote party
has hung up.
disable: Do not perform line reversal when the line enters the idle
condition.
enable: Activates the Reversal on Idle feature as described above.
Context
- MIB
- MX-FXS-MIB
- OID
.1.3.6.1.4.1.4935.15.40.1.125- Type
- scalar
- Access
- readwrite
- Status
- deprecated
- Parent
- fxsMIBObjects
- Siblings
- 15
Values & Constraints
Type Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fxsByPassEnable Enable the bypass service.
disable : The port with the bypass service is never
redirected on the bypass line.
enable : When the port with the bypas… | scalar | Enumeration | .1.3.6.1.4.1.4935.15.40.1.1 |
| fxsCalleeHangupDelay The amount of time, in seconds, the unit waits after the
called user hangs up before signaling the end of the call.
This delay is effective only when the fxsCalleeHangu… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.100 |
| fxsPolarityAndDenialBehavior Determines how the line polarity is used to signal the beginning and end of a call.
noReversal :
Polarity reversal is not used. A short power drop is made at the end… | scalar | Enumeration | .1.3.6.1.4.1.4935.15.40.1.135 |
| fxsPowerDropOnDisconnectDuration Determines the power drop duration that is made at the end
of a call when the call is disconnected by the remote party.
This value is expressed in milliseconds (ms).
… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.140 |
| fxsBlankAnonymousCallerId Instructs the FXS unit to blank out the name portion of the received
caller ID whenever 'anonymous' (case insensitive) is used to identify
the originator of the call.
d… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.150 |
| fxsFskMarkoutBits Determines the number of markout bits that are added after
the checksum in FSK signals sent to the phone when it's on hook.
The Bellcore 202 standard specifies that the… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.155 |
| fxsCallingNumberCriteria Expression that the calling number must match in
order to apply the transformation specified in
fxsCallingNumberTransformation.
The criteria must be a regular expressio… | scalar | OctetString | .1.3.6.1.4.1.4935.15.40.1.160 |
| fxsCallingNumberTransformation Transformation applied on the calling number if it matches
the expression specified in fxsCallingNumberCriteria.
'\0' to '\9' are replaced by the corresponding group in… | scalar | OctetString | .1.3.6.1.4.1.4935.15.40.1.161 |
| fxsEpSpecificLoopCurrentTable Table that contains loop current configuration indexed by
endpoint number. | table | - | .1.3.6.1.4.1.4935.15.40.1.190 |
| fxsLoopCurrent Current flowing through the current detector that
permits the detection of the on-hook and off-hook states.
The loop current is in mA.
Some hardware platforms may suppo… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.2 |
| fxsEmergencyBypass | node | - | .1.3.6.1.4.1.4935.15.40.1.200 |
| fxsFlashHookDetectionDelayMin Minimum time in ms the hook switch must remain pressed
to perform a flash hook. | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.3 |
| fxsFlashHookDetectionDelayMax Maximum time in ms the hook switch can remain pressed
to perform a flash hook. | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.4 |
| fxsLoopCurrentDropEnable Instructs the FXS unit to suppress loop current on its ports
when they cannot be used or when the IP connection
is lost.
disable: Loop current is unaffected by the port… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.50 |
| fxsCalleeHangupSupervision Determines whether call clearing occurs as soon as the called user
is the first to hang up a received call. This variable has no
effect when the user acts as the calling party.
… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.75 |