fxsByPassEnable
MX-FXS-MIB ·
.1.3.6.1.4.1.4935.15.40.1.1
Object
scalar
r/w
Enumeration
Enable the bypass service.
disable : The port with the bypass service is never
redirected on the bypass line.
enable : When the port with the bypass service is unusable
(ifAdminUsageState is idle-unusable), it will be
redirected to the bypass line. When this port
becomes usable again (ifAdminUsageState is idle),
the redirection is stopped within 10 seconds if
the bypass line is unused or 10 seconds after
the termination of the call.
NOTE: The control of the bypass service is only possible
when the unit is powered on. When power is off, the
bypass service is always enabled.
Context
- MIB
- MX-FXS-MIB
- OID
.1.3.6.1.4.1.4935.15.40.1.1- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- fxsMIBObjects
- Siblings
- 15
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fxsCalleeHangupDelay The amount of time, in seconds, the unit waits after the
called user hangs up before signaling the end of the call.
This delay is effective only when the fxsCalleeHangu… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.100 |
| fxsReversalOnIdleEnable deprecated This object is deprecated. Therefore, agents may or may not implement it.
Use fxsPolarityAndDenialBehavior instead.
The Reversal on Idle feature is used because… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.125 |
| fxsPolarityAndDenialBehavior Determines how the line polarity is used to signal the beginning and end of a call.
noReversal :
Polarity reversal is not used. A short power drop is made at the end… | scalar | Enumeration | .1.3.6.1.4.1.4935.15.40.1.135 |
| fxsPowerDropOnDisconnectDuration Determines the power drop duration that is made at the end
of a call when the call is disconnected by the remote party.
This value is expressed in milliseconds (ms).
… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.140 |
| fxsBlankAnonymousCallerId Instructs the FXS unit to blank out the name portion of the received
caller ID whenever 'anonymous' (case insensitive) is used to identify
the originator of the call.
d… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.150 |
| fxsFskMarkoutBits Determines the number of markout bits that are added after
the checksum in FSK signals sent to the phone when it's on hook.
The Bellcore 202 standard specifies that the… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.155 |
| fxsCallingNumberCriteria Expression that the calling number must match in
order to apply the transformation specified in
fxsCallingNumberTransformation.
The criteria must be a regular expressio… | scalar | OctetString | .1.3.6.1.4.1.4935.15.40.1.160 |
| fxsCallingNumberTransformation Transformation applied on the calling number if it matches
the expression specified in fxsCallingNumberCriteria.
'\0' to '\9' are replaced by the corresponding group in… | scalar | OctetString | .1.3.6.1.4.1.4935.15.40.1.161 |
| fxsEpSpecificLoopCurrentTable Table that contains loop current configuration indexed by
endpoint number. | table | - | .1.3.6.1.4.1.4935.15.40.1.190 |
| fxsLoopCurrent Current flowing through the current detector that
permits the detection of the on-hook and off-hook states.
The loop current is in mA.
Some hardware platforms may suppo… | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.2 |
| fxsEmergencyBypass | node | - | .1.3.6.1.4.1.4935.15.40.1.200 |
| fxsFlashHookDetectionDelayMin Minimum time in ms the hook switch must remain pressed
to perform a flash hook. | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.3 |
| fxsFlashHookDetectionDelayMax Maximum time in ms the hook switch can remain pressed
to perform a flash hook. | scalar | Unsigned32 | .1.3.6.1.4.1.4935.15.40.1.4 |
| fxsLoopCurrentDropEnable Instructs the FXS unit to suppress loop current on its ports
when they cannot be used or when the IP connection
is lost.
disable: Loop current is unaffected by the port… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.50 |
| fxsCalleeHangupSupervision Determines whether call clearing occurs as soon as the called user
is the first to hang up a received call. This variable has no
effect when the user acts as the calling party.
… | scalar | MX-TCMxEnableState | .1.3.6.1.4.1.4935.15.40.1.75 |