genEquipRadioCfgRadioMultiRadioSignalDegradeAdmin
MWRM-RADIO-MIB ·
.1.3.6.1.4.1.2281.10.7.2.1.17
Object
This parameter configures whether in Multi-Radio mode data stops being distributed to the radio in case of a signal degraded condition
Context
- MIB
- MWRM-RADIO-MIB
- OID
.1.3.6.1.4.1.2281.10.7.2.1.17- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- genEquipRadioCfgEntry
- Table
- genEquipRadioCfgTable
- Siblings
- 22
Syntax
MWRM-UNIT-MIBEnableDisable
- Source
- MWRM-UNIT-MIBEnableDisable
- Base type
Enumeration
Values & Constraints
Object Constraints
range: 0-16
Type Values
2 | enable |
3 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| genEquipRadioCfgRadioId This value is the radio ID that serves as this table Index | column | MWRM-UNIT-MIBRadioId | .1.3.6.1.4.1.2281.10.7.2.1.1 |
| genEquipRadioCfgRadioTrafficPriorityScheme this parameter configures the relative priority of different traffic streams.
High-tdm-over-high-ethernet gives priorities as follows:
(1) TDM high priority (2) Ethernet high prio… | column | Enumeration | .1.3.6.1.4.1.2281.10.7.2.1.10 |
| genEquipRadioCfgRadioHiPriorityEthernetBW this parameter configures the amount of bandwith reserved for high-priority Ethernet.
It must be a number in resolution of 2.048 Mbit/s for E1 systems or 1.544 Mbit/s for T1 syste… | column | Integer32 | .1.3.6.1.4.1.2281.10.7.2.1.11 |
| genEquipRadioCfgRadioMultiRadioEnable this parameter enables/disables the multi-radio feature for this radio.
Notice that for the feature to work it must be configured in two adjacent radios (odd and even slots) | column | MWRM-UNIT-MIBEnableDisable | .1.3.6.1.4.1.2281.10.7.2.1.12 |
| genEquipRadioCfgRadioMultiRadioBlockLocalTraffic this parameter allows stopping distribution of data to different radios in Multi-Radio mode for debugging purposes | column | Enumeration | .1.3.6.1.4.1.2281.10.7.2.1.13 |
| genEquipRadioCfgRadioMultiRadioBlockMateTraffic this parameter allows stopping distribution of data to the radio in the mate IDU in Multi-Radio mode for debugging purposes | column | Enumeration | .1.3.6.1.4.1.2281.10.7.2.1.14 |
| genEquipRadioCfgRadioCurrentAvailableCapacity This parameter indicates the maximum possible capacity available for Ethernet.
This sets a top limit for amount of high-priority Ethernet bandwidth | column | Integer32 | .1.3.6.1.4.1.2281.10.7.2.1.15 |
| genEquipRadioCfgRadioMultiRadioExcessiveBERAdmin This parameter configures whether in Multi-Radio mode data stops being distributed to the radio in
case of an excessive BER condition | column | MWRM-UNIT-MIBEnableDisable | .1.3.6.1.4.1.2281.10.7.2.1.16 |
| genEquipRadioCfgEnAlarmGenOnRslDegrade TEnable/Disable alarm and trapgeneration on RSL degradationbelow user defined threshold.If enabled,
trap and alarm willbe generated when current RSLlevel degrades below userdefine… | column | MWRM-UNIT-MIBEnableDisable | .1.3.6.1.4.1.2281.10.7.2.1.18 |
| genEquipRadioCfgAlarmGenRslNominalLevel RSL nominal level [in dBm] foralarm and event generation. | column | Integer32 | .1.3.6.1.4.1.2281.10.7.2.1.19 |
| genEquipRadioCfgLinkId Radio configuration link ID | column | Integer32 | .1.3.6.1.4.1.2281.10.7.2.1.2 |
| genEquipRadioCfgAlarmGenRslDegradationMargin RSL degradation margin [in dB]for alarm and eventgeneration. The margin isrelative to the nominal RSLlevel | column | Integer32 | .1.3.6.1.4.1.2281.10.7.2.1.20 |
| genEquipRadioCfgLinkShutDownOnRadioFailure This parameter enables shutting down the link and initiating automatic
state propagation upon a failure in each one of the radios.
Radio failure condition is determined by user co… | column | MWRM-UNIT-MIBEnableDisable | .1.3.6.1.4.1.2281.10.7.2.1.21 |
| genEquipRadioCfgLoopbackTimeout The timeout in minutes for automatic termination of the loopback. The value '0' refers to 'no timeout'. | column | Integer32 | .1.3.6.1.4.1.2281.10.7.2.1.22 |
| genEquipRadioCfgAbcMode TThe radio mode (multi direction or multi carrier). | column | Enumeration | .1.3.6.1.4.1.2281.10.7.2.1.23 |
| genEquipRadioCfgMACHeaderCompression The Admin state of the MAC header compression. | column | MWRM-UNIT-MIBEnableDisable | .1.3.6.1.4.1.2281.10.7.2.1.3 |
| genEquipRadioCfgClearCounters Setting this parameter to ON will clear the radio counters. | column | MWRM-UNIT-MIBOffOn | .1.3.6.1.4.1.2281.10.7.2.1.4 |
| genEquipRadioCfgIfLoopback The administrative state of the IF loopback. | column | Enumeration | .1.3.6.1.4.1.2281.10.7.2.1.5 |
| genEquipRadioCfgExcessiveBERThreshold The BER threshold that when exceeded will be considered as 'Excessive BER'. | column | ThresholdExponent | .1.3.6.1.4.1.2281.10.7.2.1.6 |
| genEquipRadioCfgSignalDegradeThreshold The BER (Bit Error Rate) threshold that when exceeded will be considered as 'Signal Degrade'. | column | ThresholdExponent | .1.3.6.1.4.1.2281.10.7.2.1.7 |
| genEquipRadioCfgRadioAdmin obsolete Radio Admin state (Enable,Disable) can be used in ifTable::ifAdminStatus | column | MWRM-UNIT-MIBEnableDisable | .1.3.6.1.4.1.2281.10.7.2.1.8 |
| genEquipRadioCfgRadioOperationalStatus The operational status of the radio interface. | column | MWRM-UNIT-MIBDownUp | .1.3.6.1.4.1.2281.10.7.2.1.9 |