genEquipRadioCfgEnAlarmGenOnRslDegrade

MWRM-RADIO-MIB · .1.3.6.1.4.1.2281.10.7.2.1.18
MIB view Table view

Object

column r/w MWRM-UNIT-MIBEnableDisable 
TEnable/Disable alarm and trapgeneration on RSL degradationbelow user defined threshold.If enabled,
trap and alarm willbe generated when current RSLlevel degrades below userdefined threshold for 5subsequent seconds.
Alarm willbe cleared after RSL level staysabove the threshold for at leastanother 5 seconds.
Thresholdis calculated as a nominal RSLlevel minus the degradationmargin.

Context

MIB
MWRM-RADIO-MIB
OID
.1.3.6.1.4.1.2281.10.7.2.1.18
Type
column
Access
readwrite
Status
current
Parent
genEquipRadioCfgEntry
Table
genEquipRadioCfgTable
Siblings
22

Syntax

MWRM-UNIT-MIBEnableDisable
Source
MWRM-UNIT-MIBEnableDisable
Base type
Enumeration

Values & Constraints

Object Constraints
range: 3600-604800
Type Values
2enable
3disable

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
genEquipRadioCfgRadioId
This value is the radio ID that serves as this table Index
columnMWRM-UNIT-MIBRadioId.1.3.6.1.4.1.2281.10.7.2.1.1
genEquipRadioCfgRadioTrafficPriorityScheme
this parameter configures the relative priority of different traffic streams. High-tdm-over-high-ethernet gives priorities as follows: (1) TDM high priority (2) Ethernet high prio…
columnEnumeration.1.3.6.1.4.1.2281.10.7.2.1.10
genEquipRadioCfgRadioHiPriorityEthernetBW
this parameter configures the amount of bandwith reserved for high-priority Ethernet. It must be a number in resolution of 2.048 Mbit/s for E1 systems or 1.544 Mbit/s for T1 syste…
columnInteger32.1.3.6.1.4.1.2281.10.7.2.1.11
genEquipRadioCfgRadioMultiRadioEnable
this parameter enables/disables the multi-radio feature for this radio. Notice that for the feature to work it must be configured in two adjacent radios (odd and even slots)
columnMWRM-UNIT-MIBEnableDisable.1.3.6.1.4.1.2281.10.7.2.1.12
genEquipRadioCfgRadioMultiRadioBlockLocalTraffic
this parameter allows stopping distribution of data to different radios in Multi-Radio mode for debugging purposes
columnEnumeration.1.3.6.1.4.1.2281.10.7.2.1.13
genEquipRadioCfgRadioMultiRadioBlockMateTraffic
this parameter allows stopping distribution of data to the radio in the mate IDU in Multi-Radio mode for debugging purposes
columnEnumeration.1.3.6.1.4.1.2281.10.7.2.1.14
genEquipRadioCfgRadioCurrentAvailableCapacity
This parameter indicates the maximum possible capacity available for Ethernet. This sets a top limit for amount of high-priority Ethernet bandwidth
columnInteger32.1.3.6.1.4.1.2281.10.7.2.1.15
genEquipRadioCfgRadioMultiRadioExcessiveBERAdmin
This parameter configures whether in Multi-Radio mode data stops being distributed to the radio in case of an excessive BER condition
columnMWRM-UNIT-MIBEnableDisable.1.3.6.1.4.1.2281.10.7.2.1.16
genEquipRadioCfgRadioMultiRadioSignalDegradeAdmin
This parameter configures whether in Multi-Radio mode data stops being distributed to the radio in case of a signal degraded condition
columnMWRM-UNIT-MIBEnableDisable.1.3.6.1.4.1.2281.10.7.2.1.17
genEquipRadioCfgAlarmGenRslNominalLevel
RSL nominal level [in dBm] foralarm and event generation.
columnInteger32.1.3.6.1.4.1.2281.10.7.2.1.19
genEquipRadioCfgLinkId
Radio configuration link ID
columnInteger32.1.3.6.1.4.1.2281.10.7.2.1.2
genEquipRadioCfgAlarmGenRslDegradationMargin
RSL degradation margin [in dB]for alarm and eventgeneration. The margin isrelative to the nominal RSLlevel
columnInteger32.1.3.6.1.4.1.2281.10.7.2.1.20
genEquipRadioCfgLinkShutDownOnRadioFailure
This parameter enables shutting down the link and initiating automatic state propagation upon a failure in each one of the radios. Radio failure condition is determined by user co…
columnMWRM-UNIT-MIBEnableDisable.1.3.6.1.4.1.2281.10.7.2.1.21
genEquipRadioCfgLoopbackTimeout
The timeout in minutes for automatic termination of the loopback. The value '0' refers to 'no timeout'.
columnInteger32.1.3.6.1.4.1.2281.10.7.2.1.22
genEquipRadioCfgAbcMode
TThe radio mode (multi direction or multi carrier).
columnEnumeration.1.3.6.1.4.1.2281.10.7.2.1.23
genEquipRadioCfgMACHeaderCompression
The Admin state of the MAC header compression.
columnMWRM-UNIT-MIBEnableDisable.1.3.6.1.4.1.2281.10.7.2.1.3
genEquipRadioCfgClearCounters
Setting this parameter to ON will clear the radio counters.
columnMWRM-UNIT-MIBOffOn.1.3.6.1.4.1.2281.10.7.2.1.4
genEquipRadioCfgIfLoopback
The administrative state of the IF loopback.
columnEnumeration.1.3.6.1.4.1.2281.10.7.2.1.5
genEquipRadioCfgExcessiveBERThreshold
The BER threshold that when exceeded will be considered as 'Excessive BER'.
columnThresholdExponent.1.3.6.1.4.1.2281.10.7.2.1.6
genEquipRadioCfgSignalDegradeThreshold
The BER (Bit Error Rate) threshold that when exceeded will be considered as 'Signal Degrade'.
columnThresholdExponent.1.3.6.1.4.1.2281.10.7.2.1.7
genEquipRadioCfgRadioAdmin obsolete
Radio Admin state (Enable,Disable) can be used in ifTable::ifAdminStatus
columnMWRM-UNIT-MIBEnableDisable.1.3.6.1.4.1.2281.10.7.2.1.8
genEquipRadioCfgRadioOperationalStatus
The operational status of the radio interface.
columnMWRM-UNIT-MIBDownUp.1.3.6.1.4.1.2281.10.7.2.1.9