vlagNewCfgHlthchkPeerIpv6
LENOVO-GbTOR-G8264-MIB ·
.1.3.6.1.4.1.26543.2.7.6.2.1.18.27
Object
scalar
r/w
OctetString
The New Health check Peer ipv6 address.
Context
- MIB
- LENOVO-GbTOR-G8264-MIB
- OID
.1.3.6.1.4.1.26543.2.7.6.2.1.18.27- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- vlagCfg
- Siblings
- 28
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-40
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| vlagIslCfg | node | - | .1.3.6.1.4.1.26543.2.7.6.2.1.18.1 |
| vlagCurCfgHlthchkPeerIp The current Health check Peer ip4 address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.26543.2.7.6.2.1.18.10 |
| vlagNewCfgHlthchkPeerIp The New Health check Peer ip4 address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.26543.2.7.6.2.1.18.11 |
| vlagCurCfgTierId Current vLAG Tier ID | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.12 |
| vlagNewCfgTierId This object is used to change the vLAG Tier ID of this switch.
vLAG consist of 2 vLAG peer switches connected by ISL link, the
system formed by the switches is referred to as a vL… | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.13 |
| vlagCurCfgStartupDelayInterval Current vLAG Startup delay interval | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.14 |
| vlagNewCfgStartupDelayInterval This object is used to change the vLAG startup Delay Timer
interval. The Timer is used to prevent traffic lost for the
vLAG ports may be up before the ISL is up. The Timer is st-
… | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.15 |
| vlagCurCfgGlobalEnable Current vLAG global status on switch. | scalar | Enumeration | .1.3.6.1.4.1.26543.2.7.6.2.1.18.16 |
| vlagNewCfgGlobalEnable Set true to enable vLAG globally or
Set false to disable vLAG globally on switch. | scalar | Enumeration | .1.3.6.1.4.1.26543.2.7.6.2.1.18.17 |
| vlagCurCfgHlthchkConnectRetryInterval In case of healtcheck TCP connection can not be
established, interval at which the retry attempt
will be made to connect to the peer. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.18 |
| vlagNewCfgHlthchkConnectRetryInterval In case of healtcheck TCP connection can not be
established, interval at which the retry attempt
will be made to connect to the peer. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.19 |
| vlagCurCfgHlthchkKeepaliveAttempts Number of keepalive attempts made before declaring
peer is down. Within this time, atleast one of the
keepalive message should have been received from the peer. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.20 |
| vlagNewCfgHlthchkKeepaliveAttempts Number of keepalive attempts made before declaring
peer is down.Within this time, atleast one of the
keepalive message should have been received from the peer. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.21 |
| vlagCurCfgHlthchkKeepaliveInterval Interval between keepalives sent over healthcheck
TCP session to keep the session alive. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.22 |
| vlagNewCfgHlthchkKeepaliveInterval Interval between keepalives sent over healthcheck
TCP session to keep the session alive. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.23 |
| vlagCurCfgAutoRecoveryInterval Current vLAG Auto Recovery interval | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.24 |
| vlagNewCfgAutoRecoveryInterval This object is used to change the vLAG Auto Recovery Timer
interval. The Timer is used to prevent all vlag ports stay
in ErrDisabled state when booting two vLAG switches but one
… | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.25 |
| vlagCurCfgHlthchkPeerIpv6 The current Health check Peer ipv6 address. | scalar | OctetString | .1.3.6.1.4.1.26543.2.7.6.2.1.18.26 |
| vlagCurCfgVrrpActive Current VLAG VRRP active mode configuration. If enabled(1), the
switch will always forward L3 traffic in all vLAG-enabled VRRP domains.
If disabled(2), the switch will forward L3 … | scalar | Enumeration | .1.3.6.1.4.1.26543.2.7.6.2.1.18.28 |
| vlagNewCfgVrrpActive Set to enabled(1) to configure the switch to always forward L3 traffic
in all vLAG-enabled VRRP domains. Set to disabled(2) to configure
the switch to forward L3 traffic in a VRRP… | scalar | Enumeration | .1.3.6.1.4.1.26543.2.7.6.2.1.18.29 |
| vlagCurCfgPeerGateway Current peer gateway configuration. If enabled(1), the vLAG switch
will act as the active gateway for packets that are addressed to the
router MAC address of the vLAG peer. | scalar | Enumeration | .1.3.6.1.4.1.26543.2.7.6.2.1.18.32 |
| vlagNewCfgPeerGateway Set enabled(1) to configure the vLAG switch to act as the active
gateway for packets that are addressed to the router MAC address
of the vLAG peer. Set to disabled(2) to configure… | scalar | Enumeration | .1.3.6.1.4.1.26543.2.7.6.2.1.18.33 |
| vlagCurCfgSwitchPriority Current vLAG switch priority | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.4 |
| vlagNewCfgSwitchPriority This object is used to change the vLAG priority of this switch. | scalar | Integer32 | .1.3.6.1.4.1.26543.2.7.6.2.1.18.5 |
| vlagCurCfgTrunkTable A table of objects of the vLAG groups configured in this
switch. | table | - | .1.3.6.1.4.1.26543.2.7.6.2.1.18.6 |
| vlagNewCfgTrunkTable A table of objects of the vLAG groups configured in this
switch. | table | - | .1.3.6.1.4.1.26543.2.7.6.2.1.18.7 |
| vlagCurCfgLacpTable A table of objects of the vLAG groups configured in this
switch. | table | - | .1.3.6.1.4.1.26543.2.7.6.2.1.18.8 |
| vlagNewCfgLacpTable A table of objects of the vLAG groups configured in this
switch. | table | - | .1.3.6.1.4.1.26543.2.7.6.2.1.18.9 |