agCurRFC4741NetconfSessionTimeout

LENOVO-GbTOR-G8264-MIB · .1.3.6.1.4.1.26543.2.7.6.1.1.1.144
MIB view Table view

Object

scalar Integer32 
Once NETCONF session setup, NETCONF server will allocate resource
for this session.
agCurRFC4741NetconfSessionTimeout indicates the number of seconds before
the resources are freed if there is no operation on this session

Context

MIB
LENOVO-GbTOR-G8264-MIB
OID
.1.3.6.1.4.1.26543.2.7.6.1.1.1.144
Type
scalar
Access
readonly
Status
current
Parent
agSystem
Siblings
119

Syntax

Integer32

Values & Constraints

Object Constraints
range: 30-3600

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
agSoftwareVersion
The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not avai…
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.10
agCurCfgSysCustomDstStart
The current Custom DST start rule
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.100
agNewCfgSysCustomDstStart
Set Custom DST start rule
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.101
agCurCfgSysCustomDstEnd
The current Custom DST end rule
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.102
agNewCfgSysCustomDstEnd
Set Custom DST end rule
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.103
agHavePanicDump
The presence of a panic dump in the flash memory.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.104
agBootVer
The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.11
agCurCfgResetControl
Current reset control state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.111
agNewCfgResetControl
Enable/disable reset control after panic.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.112
agCurCfgSysDlight
Current daylight savings time status.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.113
agNewCfgSysDlight
Enable/disable daylight savings time.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.114
agCurCfgErrDisableRecovery
This object indicates whether the system will automatically re-enable an error-disabled port after the time interval indicated by agCurCfgErrDisableTimeout has elapsed. A port is …
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.115
agNewCfgErrDisableRecovery
This object specifies whether the system should automatically re-enable an error-disabled port. Use this object to change the global setting of the error-disable recovery action.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.116
agCurCfgErrDisableTimeout
This object indicates the time, in seconds, that the system will wait before it automatically re-enables any port that is in error-disabled state.
scalarseconds Integer32.1.3.6.1.4.1.26543.2.7.6.1.1.1.117
agNewCfgErrDisableTimeout
This object specifies the time, in seconds, that the system should wait before it automatically re-enables a port that is in error-disabled state. Use this object to change the g…
scalarseconds Integer32.1.3.6.1.4.1.26543.2.7.6.1.1.1.118
agCurCfgTelnetAccess
Current telnet access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.119
agImage1Ver
The version of the software image stored in image 1 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid…
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.12
agNewCfgTelnetAccess
Enable/disable telnet access.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.120
agCurCfgDcbx
Current DCBX state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.121
agNewCfgDcbx
Enable/disable DCBX feature.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.122
serverPortsCurCfgPorts
The current configured server port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || …
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.127
serverPortsNewCfgPorts
New configuration server port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |…
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.128
serverPortsNewCfgAddPort
The port to be added to the server ports list. A '0' value is returned when read.
scalarPortNumber.1.3.6.1.4.1.26543.2.7.6.1.1.1.129
agImage2Ver
The version of the software image stored in image 2 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid…
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.13
serverPortsNewCfgRemovePort
The port to be removed from the server ports list. A '0' value is returned when read.
scalarPortNumber.1.3.6.1.4.1.26543.2.7.6.1.1.1.130
agCurBootProfile
Profile that will be used by the switch after reset
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.131
agNewBootProfile
Configure the profile that will be used by the switch after reset
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.132
agNetboot
Ena/dis loading of config over n/w during bootup
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.133
agNetbootTftpAddr
Tftp server address from where config file needs to be downloaded
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.26543.2.7.6.1.1.1.134
agNetbootCfgFile
Config file location on tftp server
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.135
agCurCfgLinkscanMode
Set linkscan mode
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.136
agNewCfgLinkscanMode
Set linkscan mode
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.137
agUSBboot
Ena/dis USB Boot capability
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.138
agCurServiceLED
Ena/dis Service Required LED
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.139
agRtcDate
The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.14
agNewServiceLED
Ena/dis Service Required LED
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.140
agUSBeject
Eject USB - eject(1) Get current USB state: usbready(2) - USB mounted nousb(3) - no USB mounted
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.141
agCurRFC4741NetconfAccess
Current NETCONF server access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.142
agNewRFC4741NetconfAccess
Enable/disable NETCONF server access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.143
agNewRFC4741NetconfSessionTimeout
Once NETCONF session setup, NETCONF server will allocate resource for this session. agNewRFC4741NetconfSessionTimeout specifies the number of seconds before the resources are free…
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.145
agCurRFC4741NetconfSshAccess
Current NETCONF server over SSH access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.146
agNewRFC4741NetconfSshAccess
Enable/disable NETCONF server over SSH access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.147
agCurRFC4741NetconfSshPort
The TCP port number that the NETCONF server over SSH is listening to in the current configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.148
agNewRFC4741NetconfSshPort
The TCP port number that the NETCONF server over SSH is listening to in the new configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.149
agRtcTime
The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.15
agCurCfgLFDStatus
This object indicates whether the system will put any port in an error-disabled state due to excessive link flaps. A port will be put in an error-disabled state due to …
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.158
agNewCfgLFDStatus
This object indicates whether the system should put any port in an error-disabled state due to excessive link flaps. Use this object to change the global setting of the Link Flap …
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.159
agLastSetErrorReason
The error reason of the last SET failure.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.16
agCurCfgLFDFlaps
This object indicates the maximum number of flaps allowed in a time period set by agCurCfgLFDTime.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.160
agNewCfgLFDFlaps
This object specifies the maximum number of flaps that should be allowed in a time period. Use this object to change the global maximum number of flaps allowed in a time period.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.161
agCurCfgLFDTime
This object indicates the length of time period in seconds during which link flaps are counted.
scalarseconds Integer32.1.3.6.1.4.1.26543.2.7.6.1.1.1.162
agNewCfgLFDTime
This object specifies the length of time period in seconds that should be used to count link flaps.
scalarseconds Integer32.1.3.6.1.4.1.26543.2.7.6.1.1.1.163
agCurCfgTrapSrcLoopIf
The index of the loopback interface that should be used for the source IP of the SNMP trap; 0 means that no loopback interface is used as the source of the SNMP trap.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.164
agNewCfgTrapSrcLoopIf
The index of the loopback interface that should be used for the source IP of the SNMP trap; 0 means that no loopback interface is used as the source of the SNMP trap.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.165
agCfgMtm
This object specifies the new value for MTM. The available MTM values are: 7159-64F (1) 7159-G64 (2) 7159-HC4 (3) 7159-HC3 (4) 7159-PAJ (5) 7159-PAK (6) 7120-64C (7)
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.166
agCurCfgDefipData
Enable or disable the use of default IP address on data interface, as configured in the current configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.167
agNewCfgDefipData
Enable or disable the use of default IP address on data interface, in the new configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.168
agCurCfgDefipMgmt
Enable or disable the use of default IP address on mgmt interface, as configured in the current configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.169
agCurCfgHttpServerPort
The TCP port number that the HTTP server is listening to in the current configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.17
agNewCfgDefipMgmt
Enable or disable the use of default IP address on mgmt interface, in the new configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.170
agNewSecurityMode
This is an action object to change switch security mode. There are thtree security modes for Lenovo switch: strict mode, compatibility mode and strict mode with SNMP not comply. …
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.177
agNewCfgSslVersionLevel
New status of SSL Server Minimum Acceptable Protocol Version.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.178
agCurCfgSslVersionLevel
Current status of SSL Server Minimum Acceptable Protocol Version.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.179
agNewCfgHttpServerPort
The TCP port number that the HTTP server is listening to in the new configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.18
agCurSecurityMode
This is an action object to change switch security mode. There are thtree security modes for Lenovo switch: strict mode, compatibility mode and strict mode with SNMP not comply. …
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.180
agCurCfgTrapHostTable
The table of current trap hosts configure.
table-.1.3.6.1.4.1.26543.2.7.6.1.1.1.184
agNewCfgTrapHostTable
The table for trap host definitions in the new configuration block.
table-.1.3.6.1.4.1.26543.2.7.6.1.1.1.185
agStaggeredReloadDelay
Delay between each reload (in minutes). By default it is 1 minute.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.186
agCurSysHostCert
Current Host Certificate
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.187
agCurCfgBootStpMaxInstances
The current maximum number of spanning tree instances or groups supported by the switch. This value can be changed by setting a new value for the agNewCfgBootStpMaxInstances objec…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.189
agCurCfgLoginBanner
The user defined login banner.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.19
agNewCfgBootStpMaxInstances
The maximum number of spanning tree instances or groups that will be supported by the switch in the next system reboot.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.190
agNewSecurityPolicy
The security policy that will take effect after the next boot.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.191
agCurSecurityPolicy
The current security policy.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.192
agSFTPEnable
In secure mode enable or disable sftp transfers.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.193
agApplyConfiguration
This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply are written to the n…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.2
agNewCfgLoginBanner
The user defined login banner.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.20
agCurCfgConsole
Enable or disable console output of syslog messages.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.23
agNewCfgConsole
Enable or disable console output of syslog messages.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.24
agCurCfgBootp
Enable or disable the use of BootP, as currently configured in the current configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.29
agSavePending
This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.3
agNewCfgBootp
Enable or disable the use of BootP, in the new configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.30
agSlotNumber
Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.31
agCurCfgSnmpTimeout
Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be freed by setting the s…
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.32
agNewCfgSnmpTimeout
Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be freed by setting the s…
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.33
agCurCfgTelnetServerPort
The TCP port number that the telnet server listens for telnet sessions.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.34
agNewCfgTelnetServerPort
The TCP port number that the telnet server listens for telnet sessions.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.35
agClearFlashDump
This is an action object to clear the FLASH dump. ok(1) is returned when this object is read.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.36
agCurCfgTrapSrcIf
The SNMP trap source interface number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.39
agSaveConfiguration
This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to backup in…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.4
agNewCfgTrapSrcIf
The SNMP trap source interface number.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.40
agCurCfgHttpsServerPort
The TCP port number that the HTTPS server is listening to in the current configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.49
agRevert
This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. This action will copy t…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.5
agNewCfgHttpsServerPort
The TCP port number that the HTTPS server is listening to in the new configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.50
agCurCfgTftpServerPort
The TCP port number that the TFTP server is listening to in the current configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.51
agNewCfgTftpServerPort
The TCP port number that the TFTP server is listening to in the new configuration block.
scalarInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.52
agRackId
The rack unique identifier.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.53
agChassis
Chassis serial number.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.54
agCurTimeZone
The time zone. Note: Locations are alphabetically ordered and the corresponding code is not reflected in CLI.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.55
agNewTimeZone
The time zone. Note: Locations are alphabetically ordered and the corresponding code is not reflected in CLI.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.56
agCurCfgIdleCLITimeout
Set idle CLI sessions timeout.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.57
agNewCfgIdleCLITimeout
Set idle CLI sessions timeout.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.26543.2.7.6.1.1.1.58
agCurCfgHttpsServerAccess
Current HTTPS server access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.62
agNewCfgHttpsServerAccess
Enable/disable HTTPS server access.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.63
agCurHttpAcces
Current HTTP server access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.66
agNewHttpAcces
New HTTP server access state.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.67
agCurCfgDhcp
Enable or disable the use of DHCP, as currently configured in the current configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.68
agNewCfgDhcp
Enable or disable the use of DHCP, in the new configuration block.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.69
agReset
This is an action object to reboot the agent. other(1) is returned always when read.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.7
agCurCfgHprompt
Current status of hprompt.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.72
agNewCfgHprompt
New status of hprompt.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.73
agCurCfgUserBBI
Current status of user configuration from BBI.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.74
agNewCfgUserBBI
New status of user configuration from BBI.
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.75
agCurCfgLoginNotice
The user defined login notice.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.78
agNewCfgLoginNotice
The user defined login notice.
scalarOctetString.1.3.6.1.4.1.26543.2.7.6.1.1.1.79
agConfigForNxtReset
The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup conf…
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.8
agImageForNxtReset
The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.9
agCurCfgSysCustomDstState
The current status of Custom DST
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.98
agNewCfgSysCustomDstState
Enable/disable Custom DST
scalarEnumeration.1.3.6.1.4.1.26543.2.7.6.1.1.1.99