hpnicfIPsecTunIKETunLocalIDVal1V2

HPN-ICF-IPSEC-MONITOR-V2-MIB · .1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1.5

Object

The value of the local peer identity for the associated IPsec
Phase-1 IKE Tunnel (IKETunLocalValue1 in the IKETunnelTable).
              
If the local peer type is ipv4Addr/ipv6Addr, this is the IP address
used to identify the local peer.
              
If the local peer type is ipv4AddrSubnet/ipv6AddrSubnet, this is
the subnet address.
              
If the local peer type is ipv4AddrRange/ipv6AddrRange, this is
the beginning IP address of the range.
              
If the local peer type is fqdn/userFqdn, this is the host name
used to identify the local peer.
              
If the local peer type is derAsn1Dn, this is the binary DER
encoding of an ASN.1 X.500 Distinguished Name [X.501] of the
principal whose certificates are being exchanged to establish
the SA.
              
If the local peer type is derAsn1Gn, this is the binary DER
encoding of an ASN.1 X.500 GeneralName [X.509] of the principal
whose certificates are being exchanged to establish the SA.
              
If the local peer type is keyId, this is an opaque byte
stream which may be used to pass vendor-specific information
necessary to identify which pre-shared key should be used to
authenticate Aggressive mode negotiations.

Context

MIB
HPN-ICF-IPSEC-MONITOR-V2-MIB
OID
.1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1.5
Type
column
Access
readonly
Status
current
Parent
hpnicfIPsecTunnelV2Entry
Groups
1

Walk the column to discover its indexed instances, or supply every index to read one instance.

Walk the column
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HPN-ICF-IPSEC-MONITOR-V2-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunLocalIDVal1V2'
More examples
Read one indexed instance
/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'HPN-ICF-IPSEC-MONITOR-V2-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunLocalIDVal1V2.<hpnicfIPsecTunIndexV2>'
Translate to a numeric OID
/usr/bin/snmptranslate -Pud -Ir -On -m 'HPN-ICF-IPSEC-MONITOR-V2-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunLocalIDVal1V2'

Syntax

Source
SNMPv2-TCDisplayString
Base type
OctetString
Display format
255a
Type Description
Represents textual information taken from the NVT ASCII
          
character set, as defined in pages 4, 10-11 of RFC 854.
          
To summarize RFC 854, the NVT ASCII repertoire specifies:
          
  - the use of character codes 0-127 (decimal)
          
  - the graphics characters (32-126) are interpreted as
    US ASCII
          
  - NUL, LF, CR, BEL, BS, HT, VT and FF have the special
    meanings specified in RFC 854
          
  - the other 25 codes have no standard interpretation
          
  - the sequence 'CR LF' means newline
          
  - the sequence 'CR NUL' means carriage-return
          
  - an 'LF' not preceded by a 'CR' means moving to the
    same column on the next line.
          
  - the sequence 'CR x' for any x other than LF or NUL is
    illegal.  (Note that this also means that a string may
    end with either 'CR LF' or 'CR NUL', but not with CR.)
          
Any object defined using this syntax may not exceed 255
characters in length.

Values & Constraints

Type Constraints
range: 0..255

Conformance