hpnicfDot11RRMCfgIntrfThres
HPN-ICF-DOT11-RRM-MIB ·
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.9
Object
column
r/w
percent Integer32
Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.
Context
- MIB
- HPN-ICF-DOT11-RRM-MIB
- OID
.1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Units
- percent
- Parent
- hpnicfDot11RRMRadioCfgEntry
- Table
- hpnicfDot11RRMRadioCfgTable
- Siblings
- 12
Syntax
percent Integer32
Values & Constraints
Object Constraints
range: 1-100
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hpnicfDot11RRMRadioType 802.11 radio type. | column | HPN-ICF-DOT11-REF-MIBHpnicfDot11RadioType | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.1 |
| hpnicfDot11RRMCfgNoiseThres Configure the noise threshold. | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.10 |
| hpnicfDot11RRMCfgPERThres Configure the CRC error threshold.
If the percentage of CRC errors reaches the threshold, RRM will perform
resource adjustment to control the situation. | column | percent Integer32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.11 |
| hpnicfDot11RRMCfgToleranceFctr Configure the tolerance level.
During dynamic frequency selection (DFS), the channel will be changed
only if there is a better channel having lesser interference and packet
error … | column | percent Integer32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.12 |
| hpnicfDot11RRMCfgAdjacencyFctr Configure the adjacency factor for the band.
If transmit power control (TPC) is configured, power will be adjusted
when the nth neighbor is detected. The value n is the adjacency… | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.13 |
| hpnicfDot11RRMCfgChlState Enable/Disable dynamic channel selection. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.2 |
| hpnicfDot11RRMCfgChlMode Configure the mode of channel selection.
This node can be configured only when dynamic channel selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.3 |
| hpnicfDot11RRMChlProntoRadioElmt Specify the AP and radio that will change channel at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of c… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.4 |
| hpnicfDot11RRMCfgPwrState Enable/Disable dynamic power selection for the band. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.5 |
| hpnicfDot11RRMCfgPwrMode Configure the mode of transmit power control.
This node can be configured only when dynamic power selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.6 |
| hpnicfDot11RRMPwrProntoRadioElmt Specify the AP and radio that will change power at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of tra… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.7 |
| hpnicfDot11RRMCfgIntrvl Configure the calibration interval. | column | minute SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.8 |