snAgGblIfIpAddr

HP-SN-AGENT-MIB · .1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.13
MIB view Table view

Object

scalar r/w RFC1155-SMIIpAddress 
The interface ip address.

Context

MIB
HP-SN-AGENT-MIB
OID
.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.13
Type
scalar
Access
readwrite
Status
current
Parent
snAgentGbl
Siblings
60

Syntax

RFC1155-SMIIpAddress
Source
RFC1155-SMIIpAddress
Base type
OctetString

Values & Constraints

Type Constraints
range: 4

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
snAgReload
Action object to reboot the agent. The following values can only be read: other(1).....agent in unknown or other state running(2)...agent running busy(4).......reload not al…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.1
snAgDefGwayIp
The default gateway (router) address.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.10
snAgImgVer
The version of the running software in the form 'major.minor.maintenance[letters]'.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.11
snAgFlashImgVer
The version of the software image saved in local storage such as flash memory in the form 'major.minor.maintenance[letters]'. If not known or not available, then the value is a ze…
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.12
snAgGblIfIpMask
The interface ip address mask.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.14
snAgGblPassword
System Security Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.15
snAgTrpRcvrCurEntry
The current total entries of the Trap Receiver Table are created.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.16
snAgGblDataRetrieveMode
By default, this mode is set to nextbootCfg(0). The VLAN Table and Port-STP Table data will be retrieved according to this mode. nextbootCfg(0).........the nextboot configuration …
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.19
snAgEraseNVRAM
Action object to erase NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash erasing(4)...agent is erasing NVRAM fla…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.2
snAgSystemLog
The system log object to indicate whether any Network Management Station(NMS) has login. The first byte of the octet string is the value decribed below and followed by 4 bytes o…
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.20
snAgGblEnableColdStartTrap
Indicates whether the SNMP agent process is permitted to generate cold start traps.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.21
snAgGblEnableLinkUpTrap
Indicates whether the SNMP agent process is permitted to generate link up traps.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.22
snAgGblEnableLinkDownTrap
Indicates whether the SNMP agent process is permitted to generate link down traps.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.23
snAgGblPasswordChangeMode
Specify which management entity is allowed to change the password. 'anyMgmtEntity' management entities are SNMP management station, console command line interface, and telnet comm…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.24
snAgGblReadOnlyCommunity
SNMP read community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.25
snAgGblReadWriteCommunity
SNMP read-write community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.26
snAgGblCurrentSecurityLevel
This represnts the current log-in security level. Each level of security requires a password to permit user for different system configurations.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.27
snAgGblSecurityLevelSet
This shows which the security level password to be set.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.28
snAgGblLevelPasswordsMask
This shows the bitmap of level passwords which successfully assigned to the system.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.29
snAgWriteNVRAM
Action object to save all configuration info to NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash writing(4)...agen…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.3
snAgGblQueueOverflow
false - The device queues are not overflow. true - The device queues are overflow.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.30
snAgGblBufferShortage
false - The device buffers are adequate. true - The device buffers are in shortage.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.31
snAgGblDmaFailure
false - The device DMAs are in good condition. true - One of the DMAs in the device fails.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.32
snAgGblResourceLowWarning
false - No, the device does not have resource-low-warning. true - Yes, the device does have resource-low-warning.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.33
snAgGblExcessiveErrorWarning
false - No, the device does not have any excessive collision, FCS errors, alignment warning etc. true - Yes, the device does have.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.34
snAgGblCpuUtilData
The statistics collection of utilization of the CPU in the device. Reading this object resets all the counters. Therefore, a user need not set snAgGblUtilCollect.
scalarRFC1155-SMIGauge.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.35
snAgGblCpuUtilCollect deprecated
enable(1) - The beginning of statistics collection of utilization of the CPU in the device. disable(0) - The end of statistics collection of utilization of the CPU in the device.…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.36
snAgGblTelnetTimeout
Telnet session idling timeout value. Writing value 0 to this object never timeouts any telnet sessions. Each value unit is one minute.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.37
snAgGblEnableWebMgmt
Enable/disable web management.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.38
snAgGblSecurityLevelBinding
This represnts the binding of a given password to which security level. A value of 255 indicates an invalid binding.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.39
snAgConfigFromNVRAM
Action object to config the switch from NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash configing(4)...configi…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.4
snAgGblEnableSLB
Enable/disable Server Load Balancing.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.40
snAgSoftwareFeature
A bit string representing the software feature of the running switch/router image. These features were conditional compiled to different product images. For each bit, exist featur…
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.41
snAgGblEnableModuleInsertedTrap
Indicates whether the SNMP agent process is permitted to generate hardware module inserted to chassis traps.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.42
snAgGblEnableModuleRemovedTrap
Indicates whether the SNMP agent process is permitted to generate hardware module removed from chassis traps.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.43
snAgGblTrapMessage
A generic trap message string.
scalarDisplayString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.44
snAgGblEnableTelnetServer
Enable or disable telnet server in device.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.45
snAgGblTelnetPassword
Telnet Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.46
snAgBuildDate
The date of the built software.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.47
snAgBuildtime
The time of the built software.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.48
snAgBuildVer
The version of the built software in the form 'major.minor.maintenance[letters]'.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.49
snAgTftpServerIp
The tftp server address, this will be used for both download/upload image file and config file.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.5
snAgGblCpuUtil1SecAvg
The statistics collection of 1 second CPU utilization.
scalarRFC1155-SMIGauge.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.50
snAgGblCpuUtil5SecAvg
The statistics collection of 5 second CPU utilization.
scalarRFC1155-SMIGauge.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.51
snAgGblCpuUtil1MinAvg
The statistics collection of 1 minute CPU utilization.
scalarRFC1155-SMIGauge.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.52
snAgGblDynMemUtil
The system dynamic memory utilization, in unit of percentage.
scalarRFC1155-SMIGauge.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.53
snAgGblDynMemTotal
The total amount of system dynamic memory, in number of bytes.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.54
snAgGblDynMemFree
The free amount of system dynamic memory, in number of bytes.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.55
snAgImgLoadSPModuleType
The switch processor module type of which that receives the downloaded image.
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.56
snAgImgLoadSPModuleNumber
The slot numner of a switch processor module that receives the downloaded image. Setting value 0 applies to all SP modules.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.57
snAgTrapHoldTime
The time in seconds for which traps will be witheld during system initialization.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.58
snAgSFlowSourceInterface
Use the ifIndex value here to specify the source interface to be used for sFlow packets. The interface should have IP address configured on it. Value of 0 indicates that source in…
scalarIF-MIBInterfaceIndex.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.59
snAgImgFname
Name of the image file including path currently associated with the system. When the object is not used, the value is a zero length string.
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.6
snAgGblTelnetLoginTimeout
Telnet session login timeout value in minutes. Default is 1 minute.
scalarInteger32.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.60
snAgGblBannerExec
EXEC process creation banner. Insert newlines using '\n' within the string.
scalarDisplayString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.61
snAgGblBannerIncoming
Incoming terminal line banner. Insert newlines using '\n' within the string.
scalarDisplayString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.62
snAgGblBannerMotd
Message-of-the-day banner. Insert newlines using '\n' within the string.
scalarDisplayString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.63
snAgImgLoad
Action object to down/up load a new image to the agent. The following values: Error values: from normal(1) to operationError(17) and tftpWrongFileType(23). loading(18) .. operat…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.7
snAgCfgFname
Name of the config file(s) including path currently associated with the system. Some agents in special situations may support a value which contains multiple file names instead of…
scalarOctetString.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.8
snAgCfgLoad
Action object to down/up load a config image to the agent. The following values can be read : Error values: from normal(1) to operationError(17) and tftpWrongFileType(29). loadi…
scalarEnumeration.1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.9