scanner-accessory-nvram4
HP-LASERJET-COMMON-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.36
Object
scalar
mandatory
OctetString
Returns the fourth part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 120..127 of the NVRAM in the scanner. The Fujitsu Controller board has a total of 128 bytes of NVRAM.
Context
- MIB
- HP-LASERJET-COMMON-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.36- Type
- scalar
- Access
- readonly
- Status
- mandatory
- Parent
- settings-scanner
- Siblings
- 48
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| scan-contrast mandatory Behaves as SCL's 'Set Scanner Contrast Level' command
which is used for setting the scanner contrast level.
Range is 0..100.
Additional information:
There are 11 different tonemap… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.1 |
| scan-upload mandatory Handshake mechanism between host and device to initiate
scan operation and coordinate the transfer of scanned
image data to the host. This object serves both as an
indicator of s… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.12 |
| default-scanner-margin-left mandatory Sets the left scanner margin. The unit of measure should
be documented in the device POS.
Additional information:
The margin value must be a multiple of 4
for alignment reasons. … | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.16 |
| default-scanner-margin-right mandatory Sets the right scanner margin. The unit of measure
should be documented in the device POS.
Additional information:
The margin value must be a multiple of 4
for alignment reasons. … | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.17 |
| scanner-accessory-serial-number mandatory Identifies the serial number for the scanner accessory.
If this is a writable object, the POS should indicate
the maximum supported string length. This string should
only use cha… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.18 |
| scanner-accessory-model-number mandatory Model number of the scanner accessory. This string
should only use characters from the US-ASCII code set.
Additional information:
Model number for the Fujitsu scanner. | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.19 |
| scan-resolution mandatory struct {
unsigned_32bit x_res; /* 1st four bytes; big endian */
unsigned_32bit y_res; /* 2nd four bytes; big endian */
}
Sets the scanning resolution. The x and y resolutions
in … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.2 |
| scanner-accessory-adf-sheet-count mandatory Total number of sheets that have been fed through the
Automatic Document Feed (ADF) accessory.
Additional information:
The Automatic Document Feed (ADF) count is
incremented each … | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.20 |
| scanner-accessory-flatbed-scan-count mandatory Total number of scans performed by a flatbed scanner
accessory.
Additional information:
The count is only incremented when a sheet is
scanned on the FLATBED. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.21 |
| scanner-accessory-cleaning-interval mandatory Recommended cleaning interval in units of sheets
scanned.
Additional information:
Recommended cleaning interval is in units of sheets
scanned. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.22 |
| scanner-accessory-cleaning-count mandatory The number of sheets scanned since the last cleaning was
performed.
Additional information:
The number of sheets that have gone through the
ADF since the last cleaning was perform… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.23 |
| scanner-accessory-maintenance-interval mandatory Recommended maintenance interval in units of sheets
scanned.
Additional information:
Recommended maintenance interval is in units of sheets
scanned. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.24 |
| scanner-accessory-maintenance-count mandatory The number of sheets scanned since the last maintenance
was performed.
Additional information:
The number of sheets that have gone through the
ADF since the last maintenance was p… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.25 |
| scanner-accessory-rom-revision mandatory ROM revision of the scanner accessory firmware.
Additional information:
ROM revision of the Fujitsu scanner is
downloaded from the scanner after the attached
scanner establishes c… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.26 |
| scanner-accessory-copy-processor-boot-revision mandatory Boot ROM revision of scanner copy processor firmware.
Boot code to initialize the copy processor, establish
communications with the scanner, and load the runtime
code.
Additional … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.27 |
| scanner-accessory-copy-processor-runtime-revision mandatory Revision of the runtime firmware for the scanner copy
processor. Runtime code which retrieves scanned data
from the scanner and sends it to other devices such as a
printer or PC … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.28 |
| scanner-accessory-service-agent-revision mandatory Revision of scanner service agent firmware. Service
agent which accepts scanned data and processes scanner
copy processor requests, resident in a device such as a
printer or PC h… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.29 |
| scan-pixel-data-type mandatory Sets the method used when scanning.
eBiLevelThesholded - One bit per pixel, using simple
thresholding of greyscale scan data.
eBiLevelHalfToned - One bit per pixel, using some… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.3 |
| scanner-accessory-control-panel-user-interface-revision mandatory Revision of the control panel user interface firmware.
Additional information:
Revision of the copy processor user interface
firmware shipped on the disk. | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.30 |
| scan-calibration | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.32 |
| scanner-accessory-nvram mandatory Returns the contents of the NVRAM (Non-Volatile RAM)
located in the scanner accessory.
Additional information:
Read bytes 0..39 of the NVRAM in the
scanner. The Fujitsu Controlle… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.33 |
| scanner-accessory-nvram2 mandatory Returns the second part of the contents of the NVRAM
(Non-Volatile RAM) located in the scanner accessory.
Additional information:
Read bytes 40..79 of the NVRAM in the
scanner. T… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.34 |
| scanner-accessory-nvram3 mandatory Returns the third part of the contents of the NVRAM
(Non-Volatile RAM) located in the scanner accessory.
Additional information:
Read bytes 80..119 of the NVRAM in the
scanner. T… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.35 |
| ui-add-option mandatory Lets the host application set up target (eg.scan) destinations.
The destinations can be a host network address and/or an
application to be launched on that host. The string sent
d… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.37 |
| ui-select-option mandatory Triggers a job from the device based on the option selected. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.38 |
| scan-compression mandatory Indicates the type of data compression applied to the
image data in the scanning upload session. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.4 |
| ui-delete-option mandatory Lets the host application delete target eg. scan
destinations that were setup with UI-ADD-OPTION.
The host sends down the entire string that was
sent earlier. The firmware looks f… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.42 |
| scanner-jam-page-count mandatory Indicates a count of the total pages jammed in the scanner'slifetime. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.43 |
| scanner-adf-page-count mandatory Indicates a count of the total pages scanned through the ADF on the
device. This may include scan to host jobs, copyjobs, and fax jobs. If
only the total pages scanned to the host… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.44 |
| scan-adf-page-count mandatory Indicates the total pages scanned through the ADF to the host from the
device. If the total pages scanned through the scanner are needed for
all features, including copy and fax j… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.45 |
| scan-image-type mandatory Indicates the image type of the scan data. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.46 |
| scan-subsample mandatory Indicates the subsampling used for Scan Data. 4:1:1, 4:2:2, and
4:3:3 subsampling are used to modify the scan image quality and amount
of scan data by reducing the number of sampl… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.47 |
| scanner-retrieve-scanline mandatory This object facilitates the sending of a scan line of data from the
scanner to a host. It grabs either raw or corrected data.
SERVICE-PASSWORD must be set correctly to use this o… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.48 |
| scanner-motor-control mandatory This objects is set to the number of steps that the scan motor should move.
SERVICE-PASSWORD must be setcorrectly to use this object.
Additional information:
This objects is set t… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.49 |
| scan-compression-factor mandatory Indicates the level of compression to be applied to the
scanned image data for upload. Range is normalized to
be between 0..100. The device POS determines the
mapping of the nor… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.5 |
| scan-height mandatory Used to set the height of a scan image in Decapoints. The use of
Decapoints as units of measure eliminates the need for the user to
understand the scanner mechanics and the devic… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.50 |
| scanner-scanline-statistics mandatory This object is used to obtain statistics about the scan line
that was previously obtained using the SCANNER-RETRIEVE-SCANLINE
object. Just as SERVICE-PASSWORD must be set correctl… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.51 |
| scan-control-descriptor mandatory Describes the control language and formats supported for this scanner. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.52 |
| scan-gamma-correction mandatory A 32-bit quantity that indicates the gamma correction to
use on the scan image. The first 16 bits indicate the
integral portion of the gamma correction. The last 16
bits indicate… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.53 |
| scan-pad-image mandatory Indicates if the scan image should be padded with white data
or not. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.54 |
| scan-upload-error mandatory Error status of the image scanning upload session. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.6 |
| scanner-accessory-total-copy-pages-printed mandatory This relates to the number of copy pages printed on a device.
The output sheet that is duplexed (made 2- sided) should be
counted as 2 pages | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.63 |
| scan-flatbed-page-count mandatory This object tracks the page count for the pages scanned from
the flatbed. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.73 |
| scanner-flatbed-page-count mandatory This object tracks the page count for the pages scanned for all
jobs from the flatbed. This includes scan to host jobs, fax
jobs, and copy jobs. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.74 |
| scanner-modular-hardware mandatory Used to specify whether optional hardware is installed or not.
Additional information:
This HP LaserJet MFP uses this object to allow
a host to query whether or not it has an ADF … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.75 |
| scanner-clock-edge-modifiers mandatory This object accesses a table used by firmware to modify clock
edge values for CCD scanner modules.
Additional information:
This object accesses a table used by firmware to modify
… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.84 |
| scan-clock-edges mandatory Returns a table of clock edges used by the scanner.
Additional information:
Returns a table of clock edges used by the scanner. | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.85 |
| scan-emulate-copy mandatory Setting this object to eYes will cause firmware to run the next
scan job as if it were a copy job, using copy values for
scanner h/w and image processing, and then return the data… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.86 |