reprint
HP-LASERJET-COMMON-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.36
Object
scalar
mandatory
r/w
Enumeration
Returns or changes the reprint (jam recovery) setting.
If eOn, then the device will reprint pages jammed pages.
If eOff, the device will not attempt to reprint jammed
pages. If eAuto, a device dependent algorithm (which
should be documented in the POS) will be used to
determine if the page gets reprinted. This object
controls all PDLs, unless a specific PDL supports its
own reprint control mechanism. To date, only PostScript
has a PDL reprint control mechanism.
Additional information:
Setting this object when the printer is not
idle, may cause a status of <noError> to be returned, but
the new value will not take effect until a job boundary
is reached. If a get is done on object before the job
boundary is reached, the value last set will be
returned.
When the value is set to eOff, pages will not be stored
in the printer, and in the event of a paper jam, will
have to be reprinted. When the value is set to eOn,
pages will be stored until delivery, therefore, in the
event of a paper jam, the page will be reprinted.
When the value is set to eAuto, the printer will behave
as though it is eOff when there is less than seven
megabytes of memory installed in the printer. When
additional memory is installed, to total at least seven
megabytes of RAM, the setting of eAuto will behave as
though it was set to eOn.
Context
- MIB
- HP-LASERJET-COMMON-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.36- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- settings-pdl
- Siblings
- 16
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| default-page-protect mandatory Returns or changes the default page protection behavior.
If eOff, the device does not reserve memory for holding
the entire raster form of a processed page. If eOn,
then memory i… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.10 |
| default-lines-per-page mandatory Returns or changes the default number of lines per page.
The POS indicates the supported values. An unsupported
value causes the printer to use the closest supported
value, causi… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.11 |
| default-vmi mandatory Returns or changes the default vertical motion index.
The unit of measure for VMI is centipoints per line.
The POS indicates the supported values. An unsupported
value causes the… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.12 |
| default-media-size mandatory This indicates the default media size. A write of an
unsupported value causes an <badValue>.
Complete list of supported media sizes along
with their dimensions are listed in the … | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.13 |
| cold-reset-media-size mandatory Returns or sets the media size that is used as the
DEFAULT-MEDIA-SIZE when a cold reset occurs. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.19 |
| default-orientation mandatory Returns or changes the default orientation. The list of
supported values should be documented in the device
POS. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.2 |
| default-media-name mandatory Returns or sets the media name that is used until the
media name is changed by a print job command.
Additional information:
This string must be one of the MEDIAn-NAME
objects. Th… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.22 |
| wide-a4 mandatory Returns or changes the wide A4 logical page size
setting. If eOn, then the margins/printable area of A4
paper will be changed to allow 80 10-pitch characters to
be printed on a s… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.37 |
| dark-courier mandatory Returns or changes the dark Courier setting. If eOn,
then the Courier font used will approximate the same
darkness as the LaserJet III printer. If eOff, then the
Courier font us… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.38 |
| default-bits-per-pixel mandatory Controls the number of levels used (per pixel) when
printing grayscale or color images. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.39 |
| default-copies mandatory Returns or changes default copies. Default copies is
the default values used by the PDL to control the number
of copies of each page in the print job that are
printed. The print… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.4 |
| form-feed mandatory Instructs the PDL processing sub-system to finishing
processing the current page of the current job. Form
feed is also known as close page or eject page. If the
PDL processing s… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.5 |
| resource-saving mandatory Returns or changes PDL resource saving. Resource saving
stores a PDL's permanent soft resources, like fonts,
even when another PDL is active. Resource saving is
also called envi… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.6 |
| maximum-resource-saving-memory mandatory This object's name is misleading. This object returns
the maximum amount of additional memory, in bytes, that
can be dedicated to holding PDL permanent soft
resources.
Additional… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.7 |
| default-vertical-black-resolution mandatory Returns or changes the value of the default vertical
black resolution. The units are dots per inch.
Additional information:
In LaserJet 4050 Series changing this OID also causes … | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.8 |
| default-horizontal-black-resolution mandatory Returns or changes the value of the default horizontal
black resolution. The units are dots per inch.
Additional information:
In LaserJet 4050 Series changing this object also ca… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.9 |