prtgeneralreset
HP-LASERJET-COMMON-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.3
Object
scalar
mandatory
r/w
Enumeration
Setting this value to `powerCycleReset', `resetToNVRAM', or
`resetToFactoryDefaults' will result in the resetting of the
printer. When read, this object will always have the value
`notResetting(3)', and a SET of the value `notResetting' shall
have no effect on the printer. Some of the defined values are
optional. However, every implementation must support at least
the values `notResetting' and 'resetToNVRAM'.
Refer to Standard Printer MIB for more details.
Additional information:
Replaces PML USER-NVRAM-RESET and POWER-ON-RESET.
The, the following sequence of events occur when this object is set to
ePpowerCycleReset, ePresetToNVRAM, or ePresetToFactoryDefaults:
1. Wait until a job boundary.
2. The paper path is flushed.
3. The printer is reset per the request. The printer will respond to PML
requests up to this point in time.
All settings will make the printer go thru its power-on initialization
routines and I/O cards are reset.
When this object is set to ePpowerCycleReset or ePresetToNVRAM, the printer
performs its power on initialization routines. I/O cards are reset, although
NVRAM on the cards is not changed, and all I/O buffers are flushed. This is
equivalent to turning the printer off and then on again.
Setting this object to ePresetToFactoryDefaults causes the same action as
ePpowerCycleReset exept that it also changes all configurable settings back
to their factory defaults. It is equivalent to doing a Cold Reset from the
control panel while turning on the printer.
Context
- MIB
- HP-LASERJET-COMMON-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.3- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- prtGeneralEntry
- Siblings
- 18
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtgeneralconfigchanges mandatory Counts configuration changes that change the capabilities of
a printer, such as the addition/deletion of input/output bins,
the addition/deletion of interpreters, or changes in me… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.1 |
| prtconsolelocalization mandatory The value of the prtLocalizationIndex corresponding to
the language, country, and character set to be used for the
console. This localization applies both to the actual display
o… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.10 |
| prtconsolenumberofdisplaylines mandatory The number of lines on the printer's physical
display. This value is 0 if there are no lines on the
physical display or if there is no physical display
Refer to Standard Printer… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.11 |
| prtconsolenumberofdisplaychars mandatory The number of characters per line displayed on the physical
display. This value is 0 if there are no lines on the
physical display or if there is no physical display
Refer to St… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.12 |
| prtconsoledisable mandatory If the object prtConsoleDisable has value
'operatorConsoleDisabled' then input is not accepted from the
operator console. If the object prtConsoleDisable has the value
'operatorCo… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.13 |
| prtgeneralstartuppage mandatory Used to enable or disable printing a startup page. If
enabled, a startup page will be printed shortly after
power-up, when the device is ready. Typical startup
pages include test … | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.14 |
| prtgeneralbannerpage mandatory Used to enable or disable printing banner pages at the
beginning of jobs. This is a master switch which applies
to all jobs, regardless of interpreter.
Refer to Standard Printer M… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.15 |
| prtgeneralprintername mandatory An administrator-specified name for this printer.
Depending upon implementation of this printer, the value of this
object may or may not be same as the value for the MIB-II
'SysNa… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.16 |
| prtgeneralserialnumber mandatory A recorded serial number for this device that indexes some type
device catalog or inventory. This value is usually set by the
device manufacturer but the MIB supports the option … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.17 |
| prtalertcriticalevents mandatory A running counter of the number of critical alert events
that have been recorded in the alert table. The value of this
object is RESET in the event of a power cycle operation (i.e… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.18 |
| prtalertallevents mandatory A running counter of the total number of alert event entries
(critical and non-critical) that have been recorded in the
alert table
Refer to Standard Printer MIB for more details.… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.19 |
| prtgeneralcurrentlocalization mandatory The value of the prtLocalizationIndex corresponding to the
current language, country, and character set to be used for
localized string values that are identified as being depende… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.2 |
| prtgeneralcurrentoperator mandatory The name of the person who is responsible for operating
this printer. It is suggested that this string include
information that would enable other humans to reach the operator,
su… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.4 |
| prtgeneralserviceperson mandatory The name of the person responsible for servicing this
printer. It is suggested that this string include information
that would enable other humans to reach the service person, suc… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.5 |
| prtinputdefaultindex mandatory The value of prtInputIndex corresponding to the default input
sub-unit: that is, this object selects the default source of
input media.
This value shall be -1 if there is no defa… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.6 |
| prtoutputdefaultindex mandatory The value of prtOutputIndex corresponding to the default
output sub-unit; that is, this object selects the default
output destination.
This value shall be -1 if there is no def… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.7 |
| prtmarkerdefaultindex mandatory The value of prtMarkerIndex corresponding to the
default marker sub-unit; that is, this object selects the
default marker.
Refer to Standard Printer MIB for more details.
… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.8 |
| prtmediapathdefaultindex mandatory The value of prtMediaPathIndex corresponding to
the default media path; that is, the selection of the
default media path.
Refer to Standard Printer MIB for more details.
… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.9 |