device-cfg-download-data-type
HP-LASERJET-COMMON-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.12
Object
scalar
mandatory
r/w
Enumeration
Indicates the type of device specific data to be downloaded.
Context
- MIB
- HP-LASERJET-COMMON-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.12- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- settings-system
- Siblings
- 25
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | eDisabled |
2 | eEnabled |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| energy-star mandatory Returns or changes the Energy Star sleep value. If the
value is greater than zero, then the device will go into
energy saving sleep mode after the print engine has been
idle for … | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1 |
| enable-engine-early-warmup mandatory This PML object is used by HP SW to enable/disable the printer
to send the signal of warm-up process early to engine. The
effect of warming up early will reduce the First Page Out… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.101 |
| device-cfg-download mandatory Handshaking mechanism between host and device to coordinate the download of device specific data.
eCfgDownloadIdle - indicates device configuration download activity is not occu… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.11 |
| device-cfg-upload mandatory Handshaking mechanism between host and device to
coordinate the upload of device specific data.
eCfgUploadIdle - indicates device configuration upload
activity is not occurrin… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.13 |
| device-cfg-upload-data-type mandatory Indicates the type of device specific data to be
uploaded. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.14 |
| download-timeout mandatory Specifies the number of seconds that device will wait
for data from the host before the device determines the
host is being unresponsive. This timeout condition may
cause the dev… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.17 |
| upload-timeout mandatory Specifies the number of seconds that device will wait
for response from the host after transmitting a unit of
data before the device determines the host is being
unresponsive. Th… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.18 |
| sleep-mode mandatory Returns eTrue if the device is in energy saving sleep
mode, otherwise returns eFalse. Setting SLEEP-MODE to
eFalse causes the device to wake up, if it is in sleep
mode. Setting … | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 |
| run-location mandatory Returns or changes the location from which code
executes. The object allows the user to pick a memory
bank to run code from which is different than the
default running code bank. … | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.21 |
| date-display mandatory Controls front-panel date display format. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.22 |
| device-cfg-param-command mandatory A C structure containing the following fields:
typedef struct {
u8bit list_id;
s8bit auto_incr;
u16bit max_index;
u16bit rec_size;
u16bit index;
u8bit data[];
} PM… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.23 |
| copier-token mandatory Provides an advisory locking mechanism for hosts to coordinate
exclusive access to a copier device. Setting the object to a
unique id will only succeed if the token is currently s… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.24 |
| fax-upload-token mandatory Provides an advisory locking mechanism for hosts to coordinate
exclusive access to the fax upload features of a device. Setting
the object to a unique id will only succeed if the … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.26 |
| fax-download-token mandatory Provides an advisory locking mechanism for hosts to coordinate
exclusive access to the fax download features of a device. Setting
the object to a unique id will only succeed if th… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.27 |
| device-config-token mandatory Provides an advisory locking mechanism for hosts to coordinate
exclusive access to a specific device or subset of device
capabilities. Setting the object to a unique id will only … | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.28 |
| mono-color-switching-mode mandatory This object allows the user to view/change the color/mono
switching mode for a device.
Additional information:
This object allows the user to view/change the color/mono
switch… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 |
| device-configure | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 |
| control-panel-button-press-delay mandatory This object gives the number of seconds to wait before
simulating the button press when CONTROL-PANEL-BUTTON-PRESS is
next called.
Additional information:
This object gives the nu… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.47 |
| low-power mandatory Returns or changes the Auto Low Power sleep value. The device
will go into energy saving Auto Low Power mode after the print
engine has been idle for the number of seconds specifi… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.49 |
| fuser-pressure-release mandatory This object is used to disengage the pressure on the fuser to
prevent roller marks on the fuser, which can occur when the
pressure is engaged for long periods of time.
Additional … | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.53 |
| control-panel-display-contrast mandatory This object returns or sets the display contrast setting if the
control panel has a display and it supports contrast
adjustment. The setting Is stored in NVRAM, so the value is
sa… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.73 |
| control-panel-lock mandatory Device control panel lock. A value of eDisabled means
the control panel is unlocked and the device's
configuration can be modified from the control panel. A
value of eEnabled me… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.8 |
| calibration-lowspeed-enable mandatory Enable or disable an optional low speed calibration. This
calibration will allow the device to obtain accurate data for
use with low speed print modes.
Additional information:
Ena… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.85 |
| service-password mandatory When set to the password value, other service related
objects become 'visible' (i.e readable) and/or become
writable. When written with any other value, the
service related objec… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.9 |
| start-engine-early-warmup mandatory This PML object is used by HP SW drivers to signal the printer
that a job is coming, and to start the warm-up process
early.The effect of warming up early will reduce the First Pa… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.99 |