collated-originals-support
HP-LASERJET-COMMON-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.42
Object
scalar
mandatory
OctetString
Indicates that the printer can create multiple, collated
'originals' of a job and shows the level of support for
this capability.
cCollatedOriginals - The printer can create multiple
collated originals, or 'mopies'. This is the base
functionality required by the other collection items.
cProofAndHold - The printer saves a copy of the job
while printing the first mopy. Later, this held job can
be released and the rest of the mopies will print.
cSecurityPrint - The printer spools the job and holds
the job until the user releases the job by entering a
password at the printer's control panel.
cAutoHighlight - The printer prints the job a number
of times with a mail distribution list prepended to each
job. A different mailing address is highlighted on each
mopy.
cCollatedAtSpeed - The printer can create multiple
collated copies where all copies after the original are
printed at engine speed.
Additional information:
Indicates that the printer can create multiple, collated
originals of a job and shows the level of support for this
capability.
cCollatedOriginals - The printer can create multiple collated
originals, or mopies.
This is the base functionality required by the other
collection items. None of them are supported by Jonah.
Without disk, this object will not exist. This will be set at
boot-up initialization. If the disk fails, in any way, then
the disk error functionality will handle the situation.
The value of this object will be:
!cCollatedOriginals - Only FLASH installed
cCollatedOriginals - IDE is installed combined
with/without FLASH
cCollatedOriginals - RAMDISK is On combined with/without FLASH
Context
- MIB
- HP-LASERJET-COMMON-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.42- Type
- scalar
- Access
- readonly
- Status
- mandatory
- Parent
- status-system
- Siblings
- 30
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| localization-language mandatory Localization language used by the device for device
generated PML strings, control panel messages, and text
contained in any of the printer generated printed pages.
The order is t… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.1 |
| user-nvram-reset mandatory Setting to eTrue causes all user NVRAM settings to
factory default settings. May also perform POWER-ON-
RESET functionality thus loosing print job data. The
POS will list which … | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.12 |
| device-mac-address mandatory The device's MAC address.
Additional information:
The device's MAC address. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.120 |
| extended-print-modes-modified mandatory This object allows the user to view whether the extended print
modes have been modified from their default settings.
Additional information:
This object allows the user to view wh… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.121 |
| date-and-time mandatory A C structure containing the following fields: typedef
struct {
ubyte yr; /* year: 0 to 99 */
ubyte mon; /* month: 1 to 12 */
ubyte day; /* day: 1 to 31… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.17 |
| not-ready-printer mandatory Indicates if any of the sub-systems in the printer are
not ready. A sub-system is not ready if the sub-system
is unable to perform its function until some sort of
intervention oc… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.2 |
| display | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.20 |
| total-ram-size mandatory Identifies total amount of RAM, in bytes, available to
the controller for general computing. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.21 |
| status-printer mandatory Indicates if any of the sub-systems in the device in a
warning condition. A warning condition exists if the
sub-system is useable, but not at its highest state of
functionality. | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.22 |
| status-controller mandatory Indicates if the hardware controller sub-system in a
warning condition. | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.23 |
| time-display mandatory Controls front-panel time display format. Set to
eTimeDisplayTwelveHour for AM/PM display. Set to
eTimeDisplayTwentyFourHour for military-type display. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.28 |
| not-ready-controller mandatory Indicates if the hardware controller sub-system in the
device is not ready. If there are no items in the
collection (i.e. no bits are set), then the hardware
controller sub-syste… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.3 |
| job-input-auto-continue-timeout mandatory The number of seconds the device waits after a job
related continuable error occurs before automatically
continuing. An example job related continuable error is
the job requestin… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.35 |
| job-input-auto-continue-mode mandatory Returns or sets the device behavior when the desired
media is not currently available.
cCancelJob - The device cancels the job. The device
POS should explain what happens if th… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.36 |
| background-message | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37 |
| error-log-clear mandatory Setting this object clears all the entries in the error
log sub-tree.
Additional information:
Setting this object removes all errors that have been
stored in the printer's non-vol… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.38 |
| not-idle mandatory Indicates if any of the sub-systems in the device are
not idle. The I/O source sub-system is considered not
idle if there is unprocessed PDL data in the device.
The PDL processin… | scalar | OctetString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.4 |
| job-output-auto-continue-timeout mandatory Returns or sets the time that the printer will wait
after an output bin becomes full and the printer is
trying to deliver a sheet of media to that output bin.
When the timeout exp… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.40 |
| device-cfg-download-error mandatory Error status of the configuration download session. POS should
indicate the actual error values reserving value 0 as NO
ERROR.
Additional information:
A value of 0 indicates NO ER… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.43 |
| device-cfg-upload-error mandatory Error status of the configuration upload session. POS should
indicate the actual error values reserving value 0 as NO
ERROR.
Additional information:
A value of 0 indicates NO ERRO… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.45 |
| on-off-line mandatory To bring the PDL processing sub-system on or off line.
If the device is a printer, then the printer does not
process print job data when the printer is off line.
PML communication… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.5 |
| localization-languages-supported mandatory The list of languages supported by the device. The
languages are primarily, but not limited to, two
character codes from ISO 639, each separated by a comma
character.
Additional i… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.52 |
| localization-countries-supported mandatory The list of countries supported by the device. The
countries are primarily, but not limited to, two
character codes from ISO 3166, each separated by a comma
character.
Additional … | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.53 |
| host-application-available-memory mandatory Returns the amount of memory, in bytes, that the device
has available for job-related processing or resources.
Also known as driver work space (DWS) memory. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.59 |
| continue mandatory A device can support a class of errors called
continuable errors. When a continuable error is
encountered, the device requires a continue event to
occur before the device will co… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.6 |
| control-panel-button-press mandatory Writing this object simulates pressing a button on the
control panel. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.60 |
| control-panel-display | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.65 |
| auto-continue mandatory Indicates if the device will automatically continue
after encountering a continuable error. If AUTO-
CONTINUE is set to eOn, the device will automatically
generate continue event… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.7 |
| install-date mandatory Identifies the date that the device was installed. The format
of the string is 'YYYYMMDDHHmmZ'. Where:
YYYY is the year.
MM is the month (1-12).
DD is the … | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.8 |
| ship-cartridge-installed-in-printer mandatory Set developer motor cams in the position needed for shipping
the cartridges installed in the printer if set to eTrue.
Additional information:
Notifies the engine that it needs to … | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.97 |