hm2RingCplConfigOperState
HM2-L2REDUNDANCY-MIB ·
.1.3.6.1.4.1.248.11.40.1.8.1.1.13
Object
column
Enumeration
Operational state of the ring coupling configuration.
slaveCouplingLinkError(2) indicates that the coupling link
is not connected with the coupling port of the slave but with
another port of the slave.
In case of outband control additional failures can be
detected:
slaveControlLinkError(3) indicates that the control
port of the slave has either no link or the link
fails.
masterControlLinkError(4) indicates that the control
link is not connected with the control port of the
master but with another port of the master.
twoSlaves(5) is returned when two slaves are connected
by the control line.
localPartnerLinkError(6) indicates that the partner coupling link
is not connected with the partner port of the slave but with
another port of the slave in local control mode.
localInvalidCouplingPort(7) indicates that in local mode the coupling
line is connected to another switch and not on the same switch like
the partner line.
couplingPortNotAvailable(8), controlPortNotAvailable(9) and
partnerPortNotAvailable(10) indicate that this port is not available
because the module related to this port is not available or the port
does not exist on this module.
Context
- MIB
- HM2-L2REDUNDANCY-MIB
- OID
.1.3.6.1.4.1.248.11.40.1.8.1.1.13- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hm2RingCouplingEntry
- Table
- hm2RingCouplingTable
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | noError |
2 | slaveCouplingLinkError |
3 | slaveControlLinkError |
4 | masterControlLinkError |
5 | twoSlaves |
6 | localPartnerLinkError |
7 | localInvalidCouplingPort |
8 | couplingPortNotAvailable |
9 | controlPortNotAvailable |
10 | partnerPortNotAvailable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hm2RingCplInterconnIfIndex Interface index of the coupling link.
Note that only those ports can be chosen
which do not belong to another L2 redundancy
mechanism like ring redundancy or dual homing
and that … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.248.11.40.1.8.1.1.1 |
| hm2RingCplControlModeOperState Control mode of the ring coupling which can only be
chosen by the slave, the master just reports his current
control mode. unknown(3) cannot be set.
In outband(1) mode an addition… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.10 |
| hm2RingCplModeOperState Mode of operation .
slaveOn(2) slave is activated.
slaveOff(1) slave is deactivated, the ring coupling is disabled and
the switch acts from now in normal rs mode. | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.11 |
| hm2RingCplOperState Operational state of an entry.
If a new entry is created by setting hm2RingCplRowStatus to create(1),
the operState returns a value of underCreation(1).
slave(2) indicates that sw… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.12 |
| hm2RingCplCouplingLinks Maximum coupling links between two coupled rings in case of a failure
in one of the coupled rings.
If there is no connection starting from the switch in slave or lo… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.14 |
| hm2RingCplExtendedDiag Additional operational states detected by the slave or in local mode.
basicRedundancyInactive(2) indicates that the coupling port has been
prevented from setting into forwarding (… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.15 |
| hm2RingCplNetCoupling Specifies the kind of the coupled net segment.
If two HIPER Rings are coupled ringCoupling(1) must be used.
In netCoupling(2) the coupled segment is no HIPER Ring topology and the… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.16 |
| hm2RingCplRedOperState Operational state of the Ring/Net coupling redundancy.
redGuaranteed(1) indicates that redundancy is guaranteed in the ring coupling.
redNotGuaranteed(2) indicates that redundancy… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.17 |
| hm2RingCplInterconnIfOpState Operational state of the coupling interface.
active(2) indicates that the port is switching.
standby(3) indicates that the port is in standby mode.
On the slave active(2) indicate… | column | Hm2CplPortOpState | .1.3.6.1.4.1.248.11.40.1.8.1.1.2 |
| hm2RingCplRowStatus Defines the status of a ring coupling database entry. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.248.11.40.1.8.1.1.22 |
| hm2RingCplControlIfIndex Interface index of the control link in case
of outband-control.
Note that only those ports can be chosen
which do not belong to another L2 redundancy
mechanism like ring redundanc… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.248.11.40.1.8.1.1.3 |
| hm2RingCplControlIfOpState Operational state of the control interface in case
of outband-control. | column | Hm2CplPortOpState | .1.3.6.1.4.1.248.11.40.1.8.1.1.4 |
| hm2RingCplPartnerInterconnIfIndex Interface index identifies the coupling link of the
partner in the ring coupling.
This variable can only be set if the
hm2RingCplControlMode is local(4). | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.248.11.40.1.8.1.1.5 |
| hm2RingCplPartnerInterconnIfOpState Operational state of the coupling interface of the
partner in the ring coupling.
active(2) indicates that the partner port is switching.
standby(3) indicates that the partner port… | column | Hm2CplPortOpState | .1.3.6.1.4.1.248.11.40.1.8.1.1.6 |
| hm2RingCplPartnerIpAddrType Partner IP Address type. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.248.11.40.1.8.1.1.7 |
| hm2RingCplPartnerIpAddr IP Address of the partner in the ring coupling. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.248.11.40.1.8.1.1.8 |
| hm2RingCplCouplingMode Ring-coupling operating mode .
In single(1) mode both coupling ports are local to the switch,
switch performs master and slave functions.
In dual-master-inband(2) mode second c… | column | Enumeration | .1.3.6.1.4.1.248.11.40.1.8.1.1.9 |