nndsxT1E1IfConfigLBO
DSX-TE1-MIB ·
.1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.6
Object
column
r/w
Enumeration
Signal attenuation at 772 kHz lbo-zero-db carrier advised LBO code A 0.0 - 5.5 db lbo-75-db carrier advised LBO code B 7.5 - 13.0 db lbo-15-db carrier advised LBO code C 15.0 - 22.0 db lbo-12-db carrier advised LBO code for E1 short haul lbo-43-db carrier advised LBO code for E1 long haul This variable can be set only for CSU linemode
Context
- MIB
- DSX-TE1-MIB
- OID
.1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- nndsxT1E1IfConfigLineEntry
- Table
- nndsxT1E1IfConfigLineTable
- Siblings
- 15
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | lbo-zero-db |
2 | lbo-75-db |
3 | lbo-15-db |
4 | lbo-225-db |
5 | lbo-12-db |
6 | lbo-43-db |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| nndsxT1E1IfIndex An integer value which is an index in to the entries of
ifTable (MIB-II) whose interface type is ds1 | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.1 |
| nndsxT1E1IfConfigTimeSlotMap Time slot map of the T1/E1 line that are being used
if it is used corresponding bit position is set. | column | OctetString | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.10 |
| nndsxT1E1IfConfigCableType The cable type that is being used.
'cable-type-coax' indicates that the cable is coaxial and the impedance is 75 ohm
'cable-type-twistedpair' indicat… | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.11 |
| nndsxT1E1IfCircuitId | column | OctetString | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.12 |
| nndsxT1E1IfContactInfo | column | OctetString | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.13 |
| nndsxT1E1IfDescription | column | OctetString | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.14 |
| nndsxT1E1IfConfigJitter Applicable only for E1 interface.
Enable/Disable jitter attenuation at LIU. | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.15 |
| nndsxT1E1IfConfigAlarmHierarchy Enable/Disable alarm hierarchy for T1/E1 interface. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.16 |
| nndsxT1E1IfConfigServiceMode Indicates the T1/E1 interface is in service if it is TRUE. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.2 |
| nndsxT1E1IfConfigLineMode Line Mode for this T1/E1 interface | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.3 |
| nndsxT1E1IfConfigLineType This variable indicates the variety of T1/E1
interpretation of the usage and error statistics.
The values, in sequence, describe:
TITLE: SPECIFICATION:
e… | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.4 |
| nndsxT1E1IfConfigLineCode This variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
b8zs refers to the use of a sp… | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.5 |
| nndsxT1E1IfConfigCableLength This variable specifies the length of the
cable in feet. | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.7 |
| nndsxT1E1IfConfigRaiAlarm Configurition of Remote Alarm Indication
Alarm generation and detection. | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.8 |
| nndsxT1E1IfConfigTransmitClock The source of Transmit Clock.
'timing-line' indicates that the recovered re-
ceive clock is used as the transmit clock.
'timing-internal' indicates … | column | Enumeration | .1.3.6.1.4.1.562.73.1.1.2.1.2.1.1.1.1.9 |