swLedInfoFrontPanelLedStatus

This object is a set of system LED indicators. The first 32 octets are 
defined as next, and following octets are for logical port LED.
              
Octet 1 is box ID led
		bit 7-6:
			reserved
		bit 5-4:
			00B = no error
			01B = system self-test error
			10B = safeguard engine entering the exhausted mode
		bit 3-0:
			The actual box ID.
			0x1 = box ID 1
			0x2 = box ID 2
			...
              								
Octet 2 is power led:
		0x01 = power work normally                    
		0x02 = power fail						
              
Octet 3 is RPS led:
		0x01 = RPS is not connected										
		0x02 = RPS is connected to switch but not ready to power the switch
		0x03 = RPS is ready to power the switch
		0x04 = RPS is powering the switch
              
Octet 4 is console led:
		0x01 = system start up
		0x02 = a user is login through console
		0x03 = no user is login through console
              
Octet 5 is master led:
		0x00 = standalone
		0x01 = master
		0x02 = back master
		0x03 = slave
              
Octet 6 is fan led:
		0x01 = all fans are OK
		0x02 = one or more fans fail
              		
Octet 7 is SD card led:
		0x01 = SD card is unplugged
		0x02 = SD card is plugged
		0x03 = reading/writing
		0x04 = read/write fail
              
Octet 8 is SIO port led:
		bit 7-2:
			reserved
		bit 1:
			SIO1 link state
			0B = linkdown
			1B = linkup
		bit 0:
			SIO2 link state
			0B = linkdown
			1B = linkup
              		
Octet 9 is POE led:
		0x01 = can not support POE
		0x02 = link/act/speed mode
		0x03 = POE mode
              		
Octet 10 is port led control state:
		0x00 = Port LED control state enabled
		0x01 = Port LED control state disabled
              		
Octet 11 is enable light state:
		0x00 = enable light state disabled
		0x01 = enable light state enabled
              		
Octet 12 is port led color state:
		0x00 = enable light Port LED color state normal
		0x01 = enable light Port LED color state amber
		0x02 = enable light Port LED color state green
              		
Octet 13-32 are reserved.
              
The continued octets are the logic port led. Each octet presents one port. 
              
There are two modes: link/act/speed mode and POE mode. 
	The link/act/speed mode presents the speed duplex of port.
	The POE mode presents if the port deliver power to PD. 
	The POE mode is supported by POE Switch only.
              
The mode is determined by Octet 9. If the switch can not support POE, 
the mode is link/act/speed only.
              		
In each octet:
link/act/speed mode:
		bit 7:
			0B = port is not activity
			1B = port is activity
		bit 6:
			0B = not combo port
			1B = combo port
              
		bit 5:
			the bit is available only when the port is combo port and linkup
			0B = fiber linkup
			1B = copper linkup
              
		bit 4:
			reserved
		bit 3:
			0B = half duplex
			1B = full duplex
              
		bit 2-0:
			0x0 = link down
			0x1 = 10Mbps
			0x2 = 100Mbps
			0x3 = 1000Mbps
			0x4 = 10Gbps
              		
POE mode:
		0x01 = no deliver power to PD
		0x02 = deliver power to PD.

MIB

DGS3120-48TC-LED-MIB

OID

.1.3.6.1.4.1.171.11.117.5.1.4.1.1.1.2

Type

column

Access

readonly

Status

current

Parent

swLedInfoEntry

Table

swLedInfoTable

Siblings

1