cseFlowEstablishedAgingTime

CISCO-SWITCH-ENGINE-MIB · .1.3.6.1.4.1.9.9.97.1.2.1
MIB view Table view

Object

scalar r/w seconds Integer32 
The adminstrative aging time for IP established flows.
The default value for this object is implementation specific.
If the cseFlowEstablishedAgingTime is not configured to the
appropriate value, it will be adjusted to the closest value.
The corresponding operational object, taken effect on the
a device, is cseFlowOperIPEstablishedAgingTime.

Context

MIB
CISCO-SWITCH-ENGINE-MIB
OID
.1.3.6.1.4.1.9.9.97.1.2.1
Type
scalar
Access
readwrite
Status
current
Units
seconds
Parent
cseFlow
Siblings
25

Syntax

seconds Integer32

Values & Constraints

Object Constraints
range: 1-65535

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cseFlowSwitchControlTable
A table used to control the L3 flow switching operation, per protocol type.
table-.1.3.6.1.4.1.9.9.97.1.2.10
cseFlowMcastMaxQueries
Maximum number of query entries allowed to be outstanding at any time, in the cseFlowMcastQueryTable. The typical value for this object is 5.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.11
cseFlowMcastQueryTable
A control table used to query the switching engine by specifying retrieval criteria for IP multicast L3 flows. Each row instance in the table represents a query with its parameter…
table-.1.3.6.1.4.1.9.9.97.1.2.12
cseFlowMcastResultTable
A table containing current IP multicast flow information corresponding to all the completed queries set up in the cseFlowMcastQueryTable, that were initiated on the switch engine(…
table-.1.3.6.1.4.1.9.9.97.1.2.13
cseFlowMcastSwitchStatus
The current status of the global IP multicast flow switching capability. When enabled, the switch engine will be able to install multicast flow entries in its L3 forwarding table…
scalarControlStatus.1.3.6.1.4.1.9.9.97.1.2.14
cseFlowIPXEstablishedAgingTime
The administrative aging time for established IPX flows. The default value for this object is implementation specific. The corresponding operational object is cseFlowOperIPXAgingT…
scalarseconds Integer32.1.3.6.1.4.1.9.9.97.1.2.15
cseStaticIpxExtRouterTable
A table of external routers which are enabled for Layer 3 IPX switching by the switching engine. This table may contain routers that have not yet been discovered by the device.
table-.1.3.6.1.4.1.9.9.97.1.2.16
cseFlowOperEstablishedAgingTime
The operational aging time for IP established flows.
scalarseconds Integer32.1.3.6.1.4.1.9.9.97.1.2.17
cseFlowOperFastAgingTime
The operational fast aging time for the established flow entries, that have less number of packets than the value set in the cseFlowOperFastAgePktThreshold,switched within this t…
scalarseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.18
cseFlowOperFastAgePktThreshold
The operational packet threshold for the cseFlowOperFastAgingTime.
scalarpackets SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.19
cseFlowFastAgingTime
The administrative fast aging time for the established flow entries, that have less number of packets than the value set in the cseFlowFastAgePktThreshold, switched within this t…
scalarseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.2
cseFlowOperIPXAgingTime
The operational aging time for established IPX flows.
scalarseconds Integer32.1.3.6.1.4.1.9.9.97.1.2.20
cseBridgedFlowStatsCtrlTable
A table controls the reporting of intra-vlan statistics for bridged flow per vlan. When a vlan is created in a device supporting this table, a corresponding entry of this table wi…
table-.1.3.6.1.4.1.9.9.97.1.2.21
cseFlowIPFlowMask
Indicates the flow mask for IP flows. If dstOnly(1) is used, it enables flows based on Layer 3 destination addresses only. If srcDst(2) is used, it enables f…
scalarEnumeration.1.3.6.1.4.1.9.9.97.1.2.22
cseFlowIPXFlowMask
Indicates the flow mask for IPX flows. If dstOnly(1) is used, it enables flows based on Layer 3 destination addresses only. If srcDst(2) is used, it enables …
scalarEnumeration.1.3.6.1.4.1.9.9.97.1.2.23
cseFlowLongAgingTime
The administrative long aging time for the established flow entries. Setting to value of 0 turns off long aging.
scalarseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.24
cseFlowExcludeTable
A table controls the flow creation based on protocol and port number. If a packet matches the protocol and port number specified in this table entries, a flow entry will not be es…
table-.1.3.6.1.4.1.9.9.97.1.2.25
cseFlowStatsTable
A table containing flow statistics information on each switching engine.
table-.1.3.6.1.4.1.9.9.97.1.2.26
cseFlowFastAgePktThreshold
The administrative packet threshold setting for the cseFlowFastAgingTime. The default for Fast Aging Packet Threshold is 0, i.e. no packets switched within the time set in cseFlow…
scalarpackets SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.3
cseRouterTable
A table containing information about all routers that are discovered by the switch, including internal and external routers.
table-.1.3.6.1.4.1.9.9.97.1.2.4
cseStaticExtRouterTable
A table of external routers which are enabled for Layer 3 IP switching by the switching engine. This table may contain routers that have not yet been discovered by the device.
table-.1.3.6.1.4.1.9.9.97.1.2.5
cseRouterVlanTable
The table listing the MAC address used by routers on particular VLANs.
table-.1.3.6.1.4.1.9.9.97.1.2.6
cseFlowMaxQueries
Maximum number of query entries allowed to be outstanding at any time, in the cseFlowQueryTable. The typical value for this object is 5.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.97.1.2.7
cseFlowQueryTable
A control table used to query the switching engine by specifying retrieval criteria for L3 flows. The resulting data for each instance of a query in this table is returned in the …
table-.1.3.6.1.4.1.9.9.97.1.2.8
cseFlowDataTable
A table containing L3 flow information corresponding to all the completed queries setup in the cseFlowQueryTable, that were initiated on the switch engine(s).
table-.1.3.6.1.4.1.9.9.97.1.2.9