cLRFProfileHDClientTrapThreshold
CISCO-LWAPP-RF-MIB ·
.1.3.6.1.4.1.9.9.778.1.1.2.1.37
Object
This object specifies the threshold number of clients per AP radio to trigger a trap. The trap ciscoLwappApClientThresholdNotify will be triggered once the count of clients on the AP radio reaches this limit. A value of zero indicates that the trap is disabled.
Context
- MIB
- CISCO-LWAPP-RF-MIB
- OID
.1.3.6.1.4.1.9.9.778.1.1.2.1.37- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cLRFProfileEntry
- Table
- cLRFProfileTable
- Siblings
- 65
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cLRFProfileName This object uniquely identifies a RF Profile. | column | OctetString | .1.3.6.1.4.1.9.9.778.1.1.2.1.1 |
| cLRFProfileDataRate11Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.10 |
| cLRFProfileDataRate6Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.11 |
| cLRFProfileDataRate9Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.12 |
| cLRFProfileDataRate12Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.13 |
| cLRFProfileDataRate18Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.14 |
| cLRFProfileDataRate24Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.15 |
| cLRFProfileDataRate36Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.16 |
| cLRFProfileDataRate48Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.17 |
| cLRFProfileDataRate54Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.18 |
| cLRFProfileRadioType This object is used to configure the radio
type for this profile. | column | CISCO-LWAPP-TC-MIBCLApIfType | .1.3.6.1.4.1.9.9.778.1.1.2.1.19 |
| cLRFProfileDescr This object specifies a human-readable description of the
profile. | column | OctetString | .1.3.6.1.4.1.9.9.778.1.1.2.1.2 |
| cLRFProfileStorageType This object represents the storage type for this
conceptual row. | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.9.9.778.1.1.2.1.20 |
| cLRFProfileRowStatus This is the status column for this row and used
to create and delete specific instances of rows
in this table. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.9.778.1.1.2.1.21 |
| cLRFProfileHighDensityMaxRadioClients This object specifies the maximum number
of clients per AP radio in high density environment. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.22 |
| cLRFProfileBandSelectProbeResponse This object specifies the AP's probe response
with clients to verify whether client can associate
on both 2.4 GHz and 5Ghz spectrum.
When set to true, AP suppresses probe response… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.23 |
| cLRFProfileBandSelectCycleCount This object specifies number of times a client probe (2.4 G-Hz)
is suppressed before the AP starts responding to the probes. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.24 |
| cLRFProfileBandSelectCycleThreshold This object specifies time threshold for a new scanning
mobile station period. Mobile station cycle counter will
increment only if mobile station scans same channel any
time aft… | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.25 |
| cLRFProfileBandSelectExpireSuppression This object specifies the duration at which
an AP waits to conduct another probe suppression. | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.26 |
| cLRFProfileBandSelectExpireDualBand This object specifies the timeout duration until
which an AP should not respond to 2.4ghz probe requests
from a dual-band client. Once this band select duration
expires the clie… | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.27 |
| cLRFProfileBandSelectClientRSSI This object specifies minimum mobile station RSSI threshold.
Mobile stations having RSSI below this value will not be
recorded in the suppressed table.
This configuration filters … | column | dbm SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.28 |
| cLRFProfileLoadBalancingWindowSize This object specifies the minimum number of clients
to be associated on an AP in order to trigger load balancing. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.29 |
| cLRFProfileTransmitPowerMin This object specifies the lower bound of transmit
power value supported by an AP. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.3 |
| cLRFProfileLoadBalancingMaxDenialCount This object specifies maximum number of association
rejections sent by AP to a mobile station for a given sequence
of association.
When a mobile station tries to as… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.30 |
| cLRFProfileCHDDataRSSIThreshold This object specifies the RSSI value for non-voice clients
i.e., clients sending only data traffic
to trigger coverage event. | column | dbm SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.31 |
| cLRFProfileCHDVoiceRSSIThreshold This object specifies the RSSI value for voice
clients to trigger coverage event. | column | dbm SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.32 |
| cLRFProfileCHDClientExceptionLevel This object specifies the minimum
number of clients required to trigger
coverage hole. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.33 |
| cLRFProfileCHDCoverageExceptionLevel This object specifies the minimum
percentage of clients in the coverage hole region
of the AP, required to trigger a
coverage hole exception | column | % SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.34 |
| cLRFProfileMulticastDataRate This object specifies the minimum
data rate at which multicast clients
can associate to AP.
A value 0 indicates that AP will automatically
adjust data rates. | column | Mbps SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.35 |
| cLRFProfile11nOnly This object specifies if 11n-client-only mode is
enabled.
A value of 'true' indicates 11n-client-only mode
enabled.
A value of 'false' indicates 11n-client-only mode
disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.36 |
| cLRFProfileInterferenceThreshold This object specifies interference threshold in %
traps are generated when interference exceeds this value . | column | percent Unsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.38 |
| cLRFProfileNoiseThreshold This object specifies the threshold number
of noise threshold between -127 and 0 dBm. | column | dBm Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.39 |
| cLRFProfileTransmitPowerMax This object specifies the uppoer bound of transmit
power value supported by an AP. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.4 |
| cLRFProfileUtilizationThreshold This object specifies the threshold of bandwidth (%)
being utilized by an access-point.
Traps are sent when this value is exceeded | column | percent Unsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.40 |
| cLRFProfileDCAForeignContribution This object specifies whether foreign interference
is taken into account for the DCA metrics.
A value of 'true' indicates that foreign interference is
is considered when DCA metr… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.41 |
| cLRFProfileDCAChannelWidth This object specifies how the system performs DCA
channel width selection for the RFProfile
twenty - 20MHz channel width supported by
this radio.
forty… | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.42 |
| cLRFProfileDCAChannelList This object specifies the 802.11 channels available to the
RF Profile. A comma separated list of integers. | column | OctetString | .1.3.6.1.4.1.9.9.778.1.1.2.1.43 |
| cLRFProfileRxSopThreshold This object specifies the receiver start of packet threshold
for the rf profile.
auto - Reverts radio receiver SOP to auto.
high - Sets radio receiver SOP to high.
low -… | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.44 |
| cLRFProfileHSRMode This object specifies whether HSR mode
for RF profile is enabled or not.
A value of 'true' indicates that HSR is enabled.
A value of 'false' indicates that HSR is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.45 |
| cLRFProfileHSRNeighborTimeoutFactor This object specifies the timeout interval
of neighbors that will be configured for RF profile.
Neighbor timeout factor will be five times the
neighbor interval | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.46 |
| cLRFProfileBandSelectClientMidRSSI This object specifies medium mobile station RSSI threshold.
Mobile station between this value and cldBandSelectClientRssi
will be recorded in suppressed table but will not be deni… | column | dbm SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.47 |
| cLRFProfileClientNetworkPreference This object represents the client network preference.
default(0) - RRM Algorithm has no preference on
the clients.
connectivity(1) - RRM Algorithm has a… | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.48 |
| cLRFProfileUnusedChannelList This object specifies the 802.11 channels present in ths un-used
channel list of RF Profile. A comma separated list of integers. | column | OctetString | .1.3.6.1.4.1.9.9.778.1.1.2.1.49 |
| cLRFProfileTransmitPowerThresholdV1 This object specifies the transmit power control
version 1 threshold for the radio resource management
algorithm. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.5 |
| cLRFProfileShutdown This object specifies if rf profile is
disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.50 |
| cLRFProfileAirTimeFairnessMode This object specifies the mode of fairness for ATF
supported APs, joined to the controller.
disable(1) - This indicates that fairness mode is
disabled.
SSID Mode(2)… | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.51 |
| cLRFProfileAirTimeFairnessOptimization This object specifies the optimization for ATF
supported APs, joined to the controller to be
configured. | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.52 |
| cLRFProfileBridgeClientAccess This object specifies whether airtime
allocation is enabled for the client access node. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.53 |
| cLRFProfileAirTimeAllocation This object specifies the percentage for airtime
allocation for the client access node. | column | Unsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.54 |
| cLRFProfileRxSopThresholdCustom This object specifies the percentage for the receiver
start of packet custom threshold for the client access node. | column | Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.55 |
| cLRFProfile11axObssPdEnable This object specifies whether 802.11ax OBSS PD spatial reuse is
enabled for the RF profile. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.56 |
| cLRFProfile11axNonSrgObssPdMax This object specifies the non-SRG OBSS PD max threshold in dBm
for the RF profile. | column | Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.57 |
| cLRFProfileNdpMode This object specifies the neighbor discovery mode of AP for this RF profile
auto - neighbor discovery mode is auto.
offChannel - neighbor discovery mode is off-channel. | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.58 |
| cLRFProfile11ax6GHzFeature This object specifies whether 802.11ax UBPR or FILS discovery
enabled for the RF profile. | column | Enumeration | .1.3.6.1.4.1.9.9.778.1.1.2.1.59 |
| cLRFProfileTransmitPowerThresholdV2 This object specifies the transmit power control
version 2 threshold for the radio resource management
algorithm. | column | dbm Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.6 |
| cLRFProfile11axBcastProbeRespInterval This object specifies the 802.11ax Broadcast Probe response
interval in msec. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.60 |
| cLRFProfileMultiBssidProfile This object specifies the Multi-BSSID profile name that is mapped
to the RF profile. | column | OctetString | .1.3.6.1.4.1.9.9.778.1.1.2.1.62 |
| cLRFProfilePSCBias This object specifies whether preferred scanning channel bias for 6 GHz DCA
is enabled or disabled for the RF profile. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.63 |
| cLRFProfile11axSrgObssPdEnable This object specifies whether 802.11ax SRG OBSS PD spatial reuse is
enabled for the RF profile. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.64 |
| cLRFProfile11axSrgObssPdMin This object specifies the SRG OBSS PD min threshold in dBm
for the RF profile. | column | Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.65 |
| cLRFProfile11axSrgObssPdMax This object specifies the SRG OBSS PD max threshold in dBm
for the RF profile. | column | Integer32 | .1.3.6.1.4.1.9.9.778.1.1.2.1.66 |
| cLRFProfilePreamblePuncture This object specifies whether Preamble puncturing is
enabled for the RF profile. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.778.1.1.2.1.67 |
| cLRFProfileDataRate1Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.7 |
| cLRFProfileDataRate2Mbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.8 |
| cLRFProfileDataRate5AndHalfMbps This object specifies the configuration for this
data rate. | column | CiscoLwappRFApDataRates | .1.3.6.1.4.1.9.9.778.1.1.2.1.9 |