cLRFProfileBandSelectClientRSSI

CISCO-LWAPP-RF-MIB · .1.3.6.1.4.1.9.9.778.1.1.2.1.28
MIB view Table view

Object

column r/w dbm SNMPv2-SMIInteger32 
This object specifies minimum mobile station RSSI threshold.
Mobile stations having RSSI below this value will not be
recorded in the suppressed table.
This configuration filters out far away mobile stations with
weaker signal strength. This will limit the number of
mobile stations on the table to a reasonable amount.

Context

MIB
CISCO-LWAPP-RF-MIB
OID
.1.3.6.1.4.1.9.9.778.1.1.2.1.28
Type
column
Access
readwrite
Status
current
Units
dbm
Parent
cLRFProfileEntry
Table
cLRFProfileTable
Siblings
65

Syntax

dbm SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cLRFProfileName
This object uniquely identifies a RF Profile.
columnOctetString.1.3.6.1.4.1.9.9.778.1.1.2.1.1
cLRFProfileDataRate11Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.10
cLRFProfileDataRate6Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.11
cLRFProfileDataRate9Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.12
cLRFProfileDataRate12Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.13
cLRFProfileDataRate18Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.14
cLRFProfileDataRate24Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.15
cLRFProfileDataRate36Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.16
cLRFProfileDataRate48Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.17
cLRFProfileDataRate54Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.18
cLRFProfileRadioType
This object is used to configure the radio type for this profile.
columnCISCO-LWAPP-TC-MIBCLApIfType.1.3.6.1.4.1.9.9.778.1.1.2.1.19
cLRFProfileDescr
This object specifies a human-readable description of the profile.
columnOctetString.1.3.6.1.4.1.9.9.778.1.1.2.1.2
cLRFProfileStorageType
This object represents the storage type for this conceptual row.
columnSNMPv2-TCStorageType.1.3.6.1.4.1.9.9.778.1.1.2.1.20
cLRFProfileRowStatus
This is the status column for this row and used to create and delete specific instances of rows in this table.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.9.9.778.1.1.2.1.21
cLRFProfileHighDensityMaxRadioClients
This object specifies the maximum number of clients per AP radio in high density environment.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.22
cLRFProfileBandSelectProbeResponse
This object specifies the AP's probe response with clients to verify whether client can associate on both 2.4 GHz and 5Ghz spectrum. When set to true, AP suppresses probe response…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.23
cLRFProfileBandSelectCycleCount
This object specifies number of times a client probe (2.4 G-Hz) is suppressed before the AP starts responding to the probes.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.24
cLRFProfileBandSelectCycleThreshold
This object specifies time threshold for a new scanning mobile station period. Mobile station cycle counter will increment only if mobile station scans same channel any time aft…
columnmilliseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.25
cLRFProfileBandSelectExpireSuppression
This object specifies the duration at which an AP waits to conduct another probe suppression.
columnseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.26
cLRFProfileBandSelectExpireDualBand
This object specifies the timeout duration until which an AP should not respond to 2.4ghz probe requests from a dual-band client. Once this band select duration expires the clie…
columnseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.27
cLRFProfileLoadBalancingWindowSize
This object specifies the minimum number of clients to be associated on an AP in order to trigger load balancing.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.29
cLRFProfileTransmitPowerMin
This object specifies the lower bound of transmit power value supported by an AP.
columndbm Integer32.1.3.6.1.4.1.9.9.778.1.1.2.1.3
cLRFProfileLoadBalancingMaxDenialCount
This object specifies maximum number of association rejections sent by AP to a mobile station for a given sequence of association. When a mobile station tries to as…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.30
cLRFProfileCHDDataRSSIThreshold
This object specifies the RSSI value for non-voice clients i.e., clients sending only data traffic to trigger coverage event.
columndbm SNMPv2-SMIInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.31
cLRFProfileCHDVoiceRSSIThreshold
This object specifies the RSSI value for voice clients to trigger coverage event.
columndbm SNMPv2-SMIInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.32
cLRFProfileCHDClientExceptionLevel
This object specifies the minimum number of clients required to trigger coverage hole.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.33
cLRFProfileCHDCoverageExceptionLevel
This object specifies the minimum percentage of clients in the coverage hole region of the AP, required to trigger a coverage hole exception
column% SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.34
cLRFProfileMulticastDataRate
This object specifies the minimum data rate at which multicast clients can associate to AP. A value 0 indicates that AP will automatically adjust data rates.
columnMbps SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.35
cLRFProfile11nOnly
This object specifies if 11n-client-only mode is enabled. A value of 'true' indicates 11n-client-only mode enabled. A value of 'false' indicates 11n-client-only mode disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.36
cLRFProfileHDClientTrapThreshold
This object specifies the threshold number of clients per AP radio to trigger a trap. The trap ciscoLwappApClientThresholdNotify will be triggered once the count of clients on the…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.37
cLRFProfileInterferenceThreshold
This object specifies interference threshold in % traps are generated when interference exceeds this value .
columnpercent Unsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.38
cLRFProfileNoiseThreshold
This object specifies the threshold number of noise threshold between -127 and 0 dBm.
columndBm Integer32.1.3.6.1.4.1.9.9.778.1.1.2.1.39
cLRFProfileTransmitPowerMax
This object specifies the uppoer bound of transmit power value supported by an AP.
columndbm Integer32.1.3.6.1.4.1.9.9.778.1.1.2.1.4
cLRFProfileUtilizationThreshold
This object specifies the threshold of bandwidth (%) being utilized by an access-point. Traps are sent when this value is exceeded
columnpercent Unsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.40
cLRFProfileDCAForeignContribution
This object specifies whether foreign interference is taken into account for the DCA metrics. A value of 'true' indicates that foreign interference is is considered when DCA metr…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.41
cLRFProfileDCAChannelWidth
This object specifies how the system performs DCA channel width selection for the RFProfile twenty - 20MHz channel width supported by this radio. forty…
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.42
cLRFProfileDCAChannelList
This object specifies the 802.11 channels available to the RF Profile. A comma separated list of integers.
columnOctetString.1.3.6.1.4.1.9.9.778.1.1.2.1.43
cLRFProfileRxSopThreshold
This object specifies the receiver start of packet threshold for the rf profile. auto - Reverts radio receiver SOP to auto. high - Sets radio receiver SOP to high. low -…
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.44
cLRFProfileHSRMode
This object specifies whether HSR mode for RF profile is enabled or not. A value of 'true' indicates that HSR is enabled. A value of 'false' indicates that HSR is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.45
cLRFProfileHSRNeighborTimeoutFactor
This object specifies the timeout interval of neighbors that will be configured for RF profile. Neighbor timeout factor will be five times the neighbor interval
columnseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.46
cLRFProfileBandSelectClientMidRSSI
This object specifies medium mobile station RSSI threshold. Mobile station between this value and cldBandSelectClientRssi will be recorded in suppressed table but will not be deni…
columndbm SNMPv2-SMIInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.47
cLRFProfileClientNetworkPreference
This object represents the client network preference. default(0) - RRM Algorithm has no preference on the clients. connectivity(1) - RRM Algorithm has a…
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.48
cLRFProfileUnusedChannelList
This object specifies the 802.11 channels present in ths un-used channel list of RF Profile. A comma separated list of integers.
columnOctetString.1.3.6.1.4.1.9.9.778.1.1.2.1.49
cLRFProfileTransmitPowerThresholdV1
This object specifies the transmit power control version 1 threshold for the radio resource management algorithm.
columndbm Integer32.1.3.6.1.4.1.9.9.778.1.1.2.1.5
cLRFProfileShutdown
This object specifies if rf profile is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.50
cLRFProfileAirTimeFairnessMode
This object specifies the mode of fairness for ATF supported APs, joined to the controller. disable(1) - This indicates that fairness mode is disabled. SSID Mode(2)…
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.51
cLRFProfileAirTimeFairnessOptimization
This object specifies the optimization for ATF supported APs, joined to the controller to be configured.
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.52
cLRFProfileBridgeClientAccess
This object specifies whether airtime allocation is enabled for the client access node.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.53
cLRFProfileAirTimeAllocation
This object specifies the percentage for airtime allocation for the client access node.
columnUnsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.54
cLRFProfileRxSopThresholdCustom
This object specifies the percentage for the receiver start of packet custom threshold for the client access node.
columnInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.55
cLRFProfile11axObssPdEnable
This object specifies whether 802.11ax OBSS PD spatial reuse is enabled for the RF profile.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.56
cLRFProfile11axNonSrgObssPdMax
This object specifies the non-SRG OBSS PD max threshold in dBm for the RF profile.
columnInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.57
cLRFProfileNdpMode
This object specifies the neighbor discovery mode of AP for this RF profile auto - neighbor discovery mode is auto. offChannel - neighbor discovery mode is off-channel.
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.58
cLRFProfile11ax6GHzFeature
This object specifies whether 802.11ax UBPR or FILS discovery enabled for the RF profile.
columnEnumeration.1.3.6.1.4.1.9.9.778.1.1.2.1.59
cLRFProfileTransmitPowerThresholdV2
This object specifies the transmit power control version 2 threshold for the radio resource management algorithm.
columndbm Integer32.1.3.6.1.4.1.9.9.778.1.1.2.1.6
cLRFProfile11axBcastProbeRespInterval
This object specifies the 802.11ax Broadcast Probe response interval in msec.
columnmilliseconds Unsigned32.1.3.6.1.4.1.9.9.778.1.1.2.1.60
cLRFProfileMultiBssidProfile
This object specifies the Multi-BSSID profile name that is mapped to the RF profile.
columnOctetString.1.3.6.1.4.1.9.9.778.1.1.2.1.62
cLRFProfilePSCBias
This object specifies whether preferred scanning channel bias for 6 GHz DCA is enabled or disabled for the RF profile.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.63
cLRFProfile11axSrgObssPdEnable
This object specifies whether 802.11ax SRG OBSS PD spatial reuse is enabled for the RF profile.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.64
cLRFProfile11axSrgObssPdMin
This object specifies the SRG OBSS PD min threshold in dBm for the RF profile.
columnInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.65
cLRFProfile11axSrgObssPdMax
This object specifies the SRG OBSS PD max threshold in dBm for the RF profile.
columnInteger32.1.3.6.1.4.1.9.9.778.1.1.2.1.66
cLRFProfilePreamblePuncture
This object specifies whether Preamble puncturing is enabled for the RF profile.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.778.1.1.2.1.67
cLRFProfileDataRate1Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.7
cLRFProfileDataRate2Mbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.8
cLRFProfileDataRate5AndHalfMbps
This object specifies the configuration for this data rate.
columnCiscoLwappRFApDataRates.1.3.6.1.4.1.9.9.778.1.1.2.1.9