cldcClientUpTime
CISCO-LWAPP-DOT11-CLIENT-MIB ·
.1.3.6.1.4.1.9.9.599.1.3.1.1.15
Object
This object indicates the duration for which the client has been associated with this device.
Context
- MIB
- CISCO-LWAPP-DOT11-CLIENT-MIB
- OID
.1.3.6.1.4.1.9.9.599.1.3.1.1.15- Type
- column
- Access
- readonly
- Status
- current
- Units
- Seconds
- Parent
- cldcClientEntry
- Table
- cldcClientTable
- Siblings
- 51
Values & Constraints
Type Constraints
range: 0..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cldcClientMacAddress This object represents the MAC address of the
client for this entry and uniquely identifies
this entry. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.599.1.3.1.1.1 |
| cldcClientIPAddress This object represents client's IP address.
This is learnt from the client details when the client
associates with the access point. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.599.1.3.1.1.10 |
| cldcClientNacState This object specifies that client's network admission
control state.
A value of 'quarantine' specifies that client goes through
posture analysis and the client traf… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.11 |
| cldcClientQuarantineVLAN This object indicates the quarantine VLAN for client. The
quarantine VLAN only allows limited access to the network. | column | Q-BRIDGE-MIBVlanId | .1.3.6.1.4.1.9.9.599.1.3.1.1.12 |
| cldcClientAccessVLAN This object indicates the access VLAN for client.
The access VLAN allows unlimited access to the network. | column | Q-BRIDGE-MIBVlanId | .1.3.6.1.4.1.9.9.599.1.3.1.1.13 |
| cldcClientLoginTime This object indicates the value of sysUpTime when the
client logged in. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.9.9.599.1.3.1.1.14 |
| cldcClientPowerSaveMode This object indicates the power management mode of
the client. | column | CISCO-LWAPP-TC-MIBCLClientPowerSaveMode | .1.3.6.1.4.1.9.9.599.1.3.1.1.16 |
| cldcClientCurrentTxRateSet This object indicates the current data rate at which the
client transmits and receives data. The data rate field is
a 16-bit unsigned value expressing the data rate of the
packet… | column | Mbit/s OctetString | .1.3.6.1.4.1.9.9.599.1.3.1.1.17 |
| cldcClientDataRateSet This object indicates the set of data rates at which the
client may transmit data. Each client can support up to
126 rates. Each octet contains an integer value
representing one… | column | OctetString | .1.3.6.1.4.1.9.9.599.1.3.1.1.18 |
| cldcClientHreapApAuth This object indicates whether the client is locally
authenticated or authenticated by the controller.
Local authentication is done only if the Access Point
connected to the client… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.19 |
| cldcClientStatus This object represents the current status of
the client. | column | CISCO-LWAPP-TC-MIBCLDot11ClientStatus | .1.3.6.1.4.1.9.9.599.1.3.1.1.2 |
| cldcClient80211uCapable This object indicates whether the client supports
802.11u feature.
The 802.11u standard allows devices such as laptop
computers or cellular phones to join a wireless LAN
widely … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.599.1.3.1.1.20 |
| cldcClientPostureState This object indicates the posture state of the client.
Posture Analysis is a state change where the client applies
the configured policies to validate access to the network.
A v… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.599.1.3.1.1.21 |
| cldcClientAclName This object indicates the ACL Name for the client.
This ACL will be used to allow or block client traffic
based on the list of rules attached to the ACL. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.22 |
| cldcClientAclApplied This object indicates the ACL applied status for the
client.
A value of 'true' indicates that the ACL is applied.
A value of 'false' indicates that the ACL is not applied.
A… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.23 |
| cldcClientRedirectUrl This object indicates the AAA override redirect URL for a
client with cldcClientPostureState enabled.
The object has a valid value when the WLAN, with which the
client has associ… | column | CISCO-TCCiscoURLStringOrEmpty | .1.3.6.1.4.1.9.9.599.1.3.1.1.24 |
| cldcClientAaaOverrideAclName This object indicates the AAA Override ACL Name for the
client if cldcClientPostureState is enabled on the wlan. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.25 |
| cldcClientAaaOverrideAclApplied This object indicates the AAA Override ACL applied status for
the client if cldcClientPostureState is enabled on the wlan.
A value of 'true' indicates that the ACL is applied.
A v… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.26 |
| cldcClientUsername This object represents the username used by the client. | column | OctetString | .1.3.6.1.4.1.9.9.599.1.3.1.1.27 |
| cldcClientSSID This object represents the SSID of the WLAN to which the
client is associated. | column | OctetString | .1.3.6.1.4.1.9.9.599.1.3.1.1.28 |
| cldcClientSecurityTagId This object represents the security group tag of the client. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.599.1.3.1.1.29 |
| cldcClientWlanProfileName This object represents the WLAN profile name
this 802.11 wireless client is connected to. | column | OctetString | .1.3.6.1.4.1.9.9.599.1.3.1.1.3 |
| cldcClientTypeKTS This object indicates whether the client is NEC KTS (National
Electrical Code Key Telephone servie) client or not.
A value of 'true' indicates that the client follows NEC
KTS SIP… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.599.1.3.1.1.30 |
| cldcClientIpv6AclName This object indicates the ACL name for the IPv6 client.
An empty string denotes no ACL has been applied. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.31 |
| cldcClientIpv6AclApplied This object indicates the ACL applied status for the IPv6
client.
A value of 'true' indicates that the ACL is applied.
A value of 'false' indicates that the ACL is not applied.
A … | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.32 |
| cldcClientDataSwitching This object indicates whether client is switching data
locally or centrally. This object is valid for flexconnect
APs.
A value of 'unknown' indicates that client data switching i… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.33 |
| cldcClientAuthentication This object indicates whether client is authentiated
locally or centrally. This object is valid for flexconnect
APs.
A value of 'unknown' indicates that client authentication is
… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.34 |
| cldcClientChannel This object indicates the access point's channel
to which the client is associated. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.599.1.3.1.1.35 |
| cldcClientAuthMode This object represents the authentication mode of client.
A value of 'none' represents that client used
open authentication to join to network.
A value of 'psk' represents that c… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.36 |
| cldcClientReasonCode This object represents the reason for disassociation
of client.
A value of 'unspecified' represents that client disassociated
with reaon unspecified.
A value of 'previousAuthNotVa… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.37 |
| cldcClientSessionID This object indicates the session
to which the client is associated. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.38 |
| cldcClientApRoamMacAddress This object indicates the MAC address of the
AP to which the client has roamed. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.599.1.3.1.1.39 |
| cldcClientWgbStatus This object represents the work group bridging
status of a DOT11 client.
A value of 'regClient' represents that the client is
a wireless client
A value of 'wgbClient' represents … | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.4 |
| cldcClientMdnsProfile This object indicates the mDNS profile name
mapped to 802.11 wireless client. It could
be mapped to the WLAN to which the client is
connected to, or the interface/interface group… | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.40 |
| cldcClientMdnsAdvCount This object indicates the number of mDNS
advertisements received on the client. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.599.1.3.1.1.41 |
| cldcClientPolicyName This object indicates the local classification
policy applied on the client. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.42 |
| cldcClientAAARole This object indicates the role string of the client
that is used as match criterion for local policy
profiling. This value is provided by radius during
authentication. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.43 |
| cldcClientDeviceType This object indicates the device type of the client.
This is identified once the profiling operation is
completed. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.599.1.3.1.1.44 |
| cldcUserAuthType This object indicates the authentication aype of user.
A value of 'open' indicates that the user authenticated using
open security.
A value of 'wepPsk' indicates that the user aut… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.45 |
| cldcClientTunnelType This object indicates the tunnel type used to send
client traffic.
A value of 'simple' indicates no tunnel is used to send
client traffic towards DS.
A value of 'pmipv6' indicates… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.46 |
| cldcClientMaxDataRate This object indicates the max data rate (Mbps)
with which the client can operate. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.599.1.3.1.1.47 |
| cldcClientHtCapable This object indicates whether the client is HT
(high throughput) capable or not.
A value of 'true' indicates that client is HT capable.
A value of 'false' indicates that client … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.599.1.3.1.1.48 |
| cldcClientVhtCapable This object indicates whether the client is VHT
(very high throughput) capable or not.
A value of 'true' indicates that client is VHT capable.
A value of 'false' indicates that … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.599.1.3.1.1.49 |
| cldcClientWgbMacAddress This object represents the MAC address of the
WGB this 802.11 wireless client to which it is
connected. This returns a non-zero value when
the cldcClientWgbStatus is wgbClient. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.599.1.3.1.1.5 |
| cldcClientCurrentTxRate This object represents the current data rate at which the
client transmits and receives data. This provides the data
rate value equivalent to the MCS value displayed in
cldcClient… | column | Mbit/s SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.599.1.3.1.1.50 |
| cldcClientiPSKTag This object indicates the PSK peer group that this client is part of.
The clients with same psk tag can be allowed to have peer to peer traffic by
configuring the wlan p2p blockin… | column | OctetString | .1.3.6.1.4.1.9.9.599.1.3.1.1.51 |
| cldcClientMobileStPolicyType Security policy of the AP to which the Mobile Station is associated. | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.52 |
| cldcClientProtocol This object represents 802.11 protocol type of the
client it used to join to wireless network.
A value of 'dot11a' represents that the client is using
802.11a standard to connect… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.6 |
| cldcAssociationMode This object represents the association mode used
by client for protected wireless traffic.
A value of 'unknown' represents that association mode used
by client for… | column | Enumeration | .1.3.6.1.4.1.9.9.599.1.3.1.1.7 |
| cldcApMacAddress This object represents the radio MAC address
of a LWAPP AP. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.599.1.3.1.1.8 |
| cldcIfType This object represents the wireless interface type. | column | CISCO-LWAPP-TC-MIBCLApIfType | .1.3.6.1.4.1.9.9.599.1.3.1.1.9 |