cienaCesRsvpteRefreshSlewNumerator
CIENA-CES-RSVPTE-MIB ·
.1.3.6.1.4.1.1271.2.1.16.1.1.19
Object
scalar
Integer32
The numerator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.
Context
- MIB
- CIENA-CES-RSVPTE-MIB
- OID
.1.3.6.1.4.1.1271.2.1.16.1.1.19- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- cienaCesRsvpteObjects
- Siblings
- 20
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-214783647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cienaCesRsvpteAdminStatus The desired administrative status of RSVP-TE. | scalar | CIENA-TCCienaGlobalState | .1.3.6.1.4.1.1271.2.1.16.1.1.1 |
| cienaCesRsvpteBlockadeMultiple The RSVP-TE value, Kb, which is the number of refresh timeout
periods after which the blockade state is deleted. | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.10 |
| cienaCesRsvpteLSPSetupPriority The setup priority to apply to LSPs that are not
signaling this parameter. 0 represents the highest
priority and 7 the lowest. The value of this object must be
numerically greater… | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.11 |
| cienaCesRsvpteLSPHoldingPriority The holding priority to apply to LSPs that are not
signaling this parameter. 0 represents the highest
priority and 7 the lowest. The value of this object must be
numerically less … | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.12 |
| cienaCesRsvpteUseHopByHop A flag to indicate that RSVP-TE should use the hop by hop
addressing scheme for the PATH and PATH-TEAR messages it
sends. If set, then the IP addresses used in the IP header
of th… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.16.1.1.13 |
| cienaCesRsvpteRestartCapable A flag to indicate whether the local node should advertise
itself as restart capable. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.16.1.1.14 |
| cienaCesRsvpteRestartTime The time in milliseconds that the local node takes to
restart RSVP-TE and the communication channel used for
RSVP-TE communication. This is advertised to neighbors in
the Restart_… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.1271.2.1.16.1.1.15 |
| cienaCesRsvpteRecoveryTime The period of time in milliseconds that the local node
would like neighbors to take to resyncronize RSVP-TE and
MPLS forwarding information after the re-establishment of
Hello con… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.1271.2.1.16.1.1.16 |
| cienaCesRsvpteMinPeerRestart The mininum period of time in milliseconds that RSVP-TE
should wait for a restart capable neighbor to regain
Hello connectivity before invoking procedures related to
communication… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.16.1.1.17 |
| cienaCesRsvpteRefreshSlewDenominator The denominator of the fraction, SlewMax, which is the
maximum allowable increase in the refresh interval, R, to
prevent state timeout while changing R. R is increased by
this fra… | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.18 |
| cienaCesRsvpteOperStatus The current operational status of RSVP-TE. | scalar | RsvpOperStatus | .1.3.6.1.4.1.1271.2.1.16.1.1.2 |
| cienaCesRsvpteGRAdminStatus RSVP-TE Graceful restart status (Enabled/Disabled). | scalar | CIENA-TCCienaGlobalState | .1.3.6.1.4.1.1271.2.1.16.1.1.20 |
| cienaCesRsvpteGRMode RSVP-TE Graceful restart Operational status. | scalar | RsvpGRMode | .1.3.6.1.4.1.1271.2.1.16.1.1.21 |
| cienaCesRsvpteRetryInterval The persistent tunnel retry interval.
This is the interval between the first failure of a persistent
tunnel and the first attempt to re-establish the tunnel.
This cannot be change… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.1271.2.1.16.1.1.3 |
| cienaCesRsvpteRetryInfiniteState The persistent tunnel retry infinity.
This is the state which when on, triggers RSVP-TE to try to restore the tunnels
infinite times. This object can only be set if RSVP-TE is glo… | scalar | Enumeration | .1.3.6.1.4.1.1271.2.1.16.1.1.4 |
| cienaCesRsvpteRetryMax The maximum number of retry attempts that will be made before a
persistent tunnel is deemed inoperable. Once in this state,
a management agent should set mplsTunnelAdminStatus to … | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.5 |
| cienaCesRsvpteRefreshInterval The RSVP-TE value, R, which is used to set the average
interval between refresh path and RESV messages. | scalar | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.16.1.1.6 |
| cienaCesRsvpteRefreshMultiple The RSVP-TE value, K, which is the number of unresponded path
or RESV refresh attempts that must be made, spaced by
the refresh interval, before the state is deemed to have
timed … | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.7 |
| cienaCesRsvpteRfrshSlewDenom deprecated This object is deprecated and the new object to provide this information is
cienaCesRsvpteRefreshSlewDenominator in this table. | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.8 |
| cienaCesRsvpteRfrshSlewNumerator deprecated This object is deprecated and the new object to provide this information is
cienaCesRsvpteRefreshSlewNumerator in this table. | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.9 |