cienaCesRsvpteRecoveryTime
CIENA-CES-RSVPTE-MIB ·
.1.3.6.1.4.1.1271.2.1.16.1.1.16
Object
scalar
SNMPv2-SMIUnsigned32
The period of time in milliseconds that the local node
would like neighbors to take to resyncronize RSVP-TE and
MPLS forwarding information after the re-establishment of
Hello connectivity. This is advertised to neighbors in
the Restart_Cap object in Hello messages.
A value of zero indicates that the node does not support
resynchronization following failure of the local node.
A value of 0xFFFFFFFF indicates an infinite recovery time.
Only used if cienaCesRsvpteRestartCapable is set to true.
For devices which only act as the Helper node, this timer
is unused and will return value 0.
Context
- MIB
- CIENA-CES-RSVPTE-MIB
- OID
.1.3.6.1.4.1.1271.2.1.16.1.1.16- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- cienaCesRsvpteObjects
- Siblings
- 20
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cienaCesRsvpteAdminStatus The desired administrative status of RSVP-TE. | scalar | CIENA-TCCienaGlobalState | .1.3.6.1.4.1.1271.2.1.16.1.1.1 |
| cienaCesRsvpteBlockadeMultiple The RSVP-TE value, Kb, which is the number of refresh timeout
periods after which the blockade state is deleted. | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.10 |
| cienaCesRsvpteLSPSetupPriority The setup priority to apply to LSPs that are not
signaling this parameter. 0 represents the highest
priority and 7 the lowest. The value of this object must be
numerically greater… | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.11 |
| cienaCesRsvpteLSPHoldingPriority The holding priority to apply to LSPs that are not
signaling this parameter. 0 represents the highest
priority and 7 the lowest. The value of this object must be
numerically less … | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.12 |
| cienaCesRsvpteUseHopByHop A flag to indicate that RSVP-TE should use the hop by hop
addressing scheme for the PATH and PATH-TEAR messages it
sends. If set, then the IP addresses used in the IP header
of th… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.16.1.1.13 |
| cienaCesRsvpteRestartCapable A flag to indicate whether the local node should advertise
itself as restart capable. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.16.1.1.14 |
| cienaCesRsvpteRestartTime The time in milliseconds that the local node takes to
restart RSVP-TE and the communication channel used for
RSVP-TE communication. This is advertised to neighbors in
the Restart_… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.1271.2.1.16.1.1.15 |
| cienaCesRsvpteMinPeerRestart The mininum period of time in milliseconds that RSVP-TE
should wait for a restart capable neighbor to regain
Hello connectivity before invoking procedures related to
communication… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.16.1.1.17 |
| cienaCesRsvpteRefreshSlewDenominator The denominator of the fraction, SlewMax, which is the
maximum allowable increase in the refresh interval, R, to
prevent state timeout while changing R. R is increased by
this fra… | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.18 |
| cienaCesRsvpteRefreshSlewNumerator The numerator of the fraction, SlewMax, which is the maximum
allowable increase in the refresh interval, R, to prevent
state timeout while changing R. R is increased by this
fract… | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.19 |
| cienaCesRsvpteOperStatus The current operational status of RSVP-TE. | scalar | RsvpOperStatus | .1.3.6.1.4.1.1271.2.1.16.1.1.2 |
| cienaCesRsvpteGRAdminStatus RSVP-TE Graceful restart status (Enabled/Disabled). | scalar | CIENA-TCCienaGlobalState | .1.3.6.1.4.1.1271.2.1.16.1.1.20 |
| cienaCesRsvpteGRMode RSVP-TE Graceful restart Operational status. | scalar | RsvpGRMode | .1.3.6.1.4.1.1271.2.1.16.1.1.21 |
| cienaCesRsvpteRetryInterval The persistent tunnel retry interval.
This is the interval between the first failure of a persistent
tunnel and the first attempt to re-establish the tunnel.
This cannot be change… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.1271.2.1.16.1.1.3 |
| cienaCesRsvpteRetryInfiniteState The persistent tunnel retry infinity.
This is the state which when on, triggers RSVP-TE to try to restore the tunnels
infinite times. This object can only be set if RSVP-TE is glo… | scalar | Enumeration | .1.3.6.1.4.1.1271.2.1.16.1.1.4 |
| cienaCesRsvpteRetryMax The maximum number of retry attempts that will be made before a
persistent tunnel is deemed inoperable. Once in this state,
a management agent should set mplsTunnelAdminStatus to … | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.5 |
| cienaCesRsvpteRefreshInterval The RSVP-TE value, R, which is used to set the average
interval between refresh path and RESV messages. | scalar | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.16.1.1.6 |
| cienaCesRsvpteRefreshMultiple The RSVP-TE value, K, which is the number of unresponded path
or RESV refresh attempts that must be made, spaced by
the refresh interval, before the state is deemed to have
timed … | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.7 |
| cienaCesRsvpteRfrshSlewDenom deprecated This object is deprecated and the new object to provide this information is
cienaCesRsvpteRefreshSlewDenominator in this table. | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.8 |
| cienaCesRsvpteRfrshSlewNumerator deprecated This object is deprecated and the new object to provide this information is
cienaCesRsvpteRefreshSlewNumerator in this table. | scalar | Integer32 | .1.3.6.1.4.1.1271.2.1.16.1.1.9 |