cadSysSyncInterval
CADANT-CMTS-SYSTEM-MIB ·
.1.3.6.1.4.1.4998.1.1.5.1.1.1
Object
scalar
Milliseconds Integer32
Nominal time between transmission of SYNC messages. (ref 6.3.2)
Context
- MIB
- CADANT-CMTS-SYSTEM-MIB
- OID
.1.3.6.1.4.1.4998.1.1.5.1.1.1- Type
- scalar
- Access
- readonly
- Status
- current
- Units
- Milliseconds
- Parent
- cadSysParams
- Siblings
- 56
Syntax
Milliseconds Integer32
Values & Constraints
Object Constraints
range: 0-200
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cadSysT5Timeout Wait for Upstream CHannel Change response. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.10 |
| cadSysT6Timeout Wait for REG-RSP and REG-ACK | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.11 |
| cadSysMiniSlotSize Size of mini-slotfor upstream transmission. Must be a
power of 2 (in units of the Timebase Tick). | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.12 |
| cadSysDSxRequestRetries Number of Timeout Retries on DSA/DSC/DSD Requests. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.13 |
| cadSysDSxResponseRetries Number of Timeout Retries on DSA/DSC/DSD Responses. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.14 |
| cadSysT7Timeout Wait for DSA/DSC/DSD Response timeout. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.15 |
| cadSysT8Timeout Wait for DSA/DSC/DSD Acknowledge timeout. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.16 |
| cadSysT9Timeout Registration timeout, the time allowed between the CMTS
sending a RNG-RSP(success) to a CM, and receiving a
REG-REQ from that same CM. | scalar | Minutes Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.17 |
| cadSysT10Timeout Wait for Transaction End timeout. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.18 |
| cadSysT11Timeout Wait for a DCC Response on the old channel. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.19 |
| cadSysUCDInterval Time between transmission of UCD messages. (ref 6.3.3) | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.2 |
| cadSysT13Timeout Maximum holding time for QOS resources for DCC. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.20 |
| cadSysDCCREQRetries Number of retries on Dynamic Channel Change Request. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.21 |
| cadSysMICEnable Enable MIC checking on the CMTS. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.22 |
| cadSysMICAuthString Encrypted MIC Authentication | scalar | OctetString | .1.3.6.1.4.1.4998.1.1.5.1.1.23 |
| cadSysAutoRecoveryEnable Enable automatic recovery of card/port/software in case
of component failure. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.24 |
| cadSysActiveIpAddress Ip Address of the active control complex. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4998.1.1.5.1.1.25 |
| cadSysSpOperMode Special operational mode. Value of 1 indicates the mode is enabled.
dqossf10cms - Allow 1.0 CMs to be stored in DocsQosServiceFlowEntry
adjrxpwrctl - Allow rx power control to be… | scalar | Bits | .1.3.6.1.4.1.4998.1.1.5.1.1.26 |
| cadSysCountsCollectionRate The period, in minutes, in which every count in the CMTS
is to be collected. If this object is set to 0, counts
collection will be disabled. | scalar | Unsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.27 |
| cadSysMaxQoSActiveTimeout Defines the maximum QoS Active Timeout the E6000 is willing to allow. If
a larger value is received in a CM request the E6000 will return this value
instead in the response (Refe… | scalar | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.28 |
| cadSysMaxQoSAdmittedTimeout Defines the maximum QoS Admitted Timeout the E6000 is willing to allow. If
a larger value is received in a CM request the E6000 will return this value
instead in the response (Re… | scalar | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.29 |
| cadSysMaxMAPPending The number of mini-slots that a CMTS is allowed to map
into the future. (ref 6.3.4) | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.3 |
| cadSysAllow10CmConcatenation Defines whether or not the E6000 will allow a modem operating in DOCSIS 1.0
mode to utilize concatenation. If this value is false and a modem operating
in 1.0 mode sends up a mo… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.30 |
| cadSysAllow10CmFragmentation Defines whether or not the E6000 will allow a modem operating in DOCSIS 1.0
mode to utilize fragmentation. If this value is false and a modem operating
in 1.0 mode sends up a mo… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.31 |
| cadSysPercentAddtlDsBwAllocated This value of this setting is used to make a percentage increase to a dynamic
downstream service flows maximum traffic rate. This is flexiblity actually
causes the E6000 to oper… | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.32 |
| cadSysMaxTrafBurstFor11CMs This is the default value that will be used to populate the Maximum Traffic Burst
for a 1.1 modem unless the maximum traffic burst TLV is explicitly provided in either
the modems … | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.33 |
| cadSysFanSpeedControlEnable obsolete Enable automatic fan speed control. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.34 |
| cadSysFlaplistPowerAdjustThreshold The threshold is used to monitor the power adjust in the flap
list. For a range request received that results in a power adjust
exceeding the threshold value will cause the count… | scalar | dB Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.35 |
| cadSysRemoteFSEnable Indicates whether the active SCM should allow mounting the
the filesystems of the standby SCM. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.36 |
| cadSysRemotePortEnable Indicates whether the active SCM should allow redirection of
the serial console of the standby SCM. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.37 |
| cadSysTcpSmoothingValue1D8U TCP smoothing value to be programmed into hardware on 1D8U CAMs. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.38 |
| cadSysTcpSmoothingValue2D12U TCP smoothing value to be programmed into hardware on 2D12U CAMs. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.39 |
| cadSysRangingInterval Time between transmission of broadcast Ranging requests. (ref 7.3.3) | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.4 |
| cadSysModemLossThreshold deprecated Minimum modem threshold triggering detection of an
upstream channel lockup. | scalar | Unsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.40 |
| cadSysPeakTrafRateFor11CMs obsolete This is the default value that will be used to populate the Peak Traffic Rate
for a 1.1 modem configuration file unless the peak traffic rate is explicitly
provided by a Service C… | scalar | DOCS-QOS3-MIBBitRate | .1.3.6.1.4.1.4998.1.1.5.1.1.41 |
| cadSysCpeHostAuthorization This variable enables the CPE Host Authorization feature. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.44 |
| cadSysMaxUcdBurstLength This variable limits the maximum UCD burst length. | scalar | bytes Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.46 |
| cadSysLO1LeakDetect This variable controls LO1 leak detection on the DMM. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.47 |
| cadMtcmConditionalOverride If set to 'true', for a MAC Domain configured for MTCM enabled operation,
the E6000 will set a registering MTCM-capable CM to be MTCM disabled (via REG-RSP message)
unless at le… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.48 |
| cadSysDelayedCpeLearning This setting only applies to modems that have BPI enabled.
When set to false(2), CPE learning is enabled during registration
when BPI initialization is initiated for those mode… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.49 |
| cadSysInvitedRangingRetries Number of retries on inviting ranging requests. (ref 9.2.4) | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.5 |
| cadSysModPriDsInRccEnabled Enable modifying primary Downstream channel in RCC of Reg-Rsp-MP.
Refer ECN 690. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.52 |
| cadSysSendTccRefIdPerFragment Settings for sending the Transmit Channel Configuration (TCC) Reference sub-type 46.1 for type 46 TCC fragmentation.
If 'true', sends 46.1 Ref ID in every type 46 TCC fragment;
If… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.53 |
| cadSysPeakTrRateUpstream This object enables support for Peak Traffic Rate in the upstream direction. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.54 |
| cadSysAllowAmbiguityOverride This object enables ambiguity resolution channel-override actions. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.55 |
| cadSysUnicastNpUsAcquisition This object enables unicast non-primary upstream channel acquisition. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.56 |
| cadSysMacMoveBlockedOnRcptDhcpPkt MAC movement is blocked on receipt of DHCP packets | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.57 |
| cadSysTftpProxy This parameter provides a global enable for the TFTP
Enforce and Dynamic Shared Secret features. In order for
the cadIfMacDomainTftpEnforce and cadIfMacDomainDynamicSecret
paramet… | scalar | Enumeration | .1.3.6.1.4.1.4998.1.1.5.1.1.58 |
| cadSysFanSpeedLevel Set the fan speed for the chassis. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.59 |
| cadSysRegistrationRequestRetries Number of retries on registration requests/responses. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.6 |
| cadSys1x1onCmAcPwrLossEnabled This object enables/disables the CMTS reaction to a AC Power Loss CM-STATUS.
If true, the CMTS will wait until cadSys1x1onCmAcPwrLossHoldoff expires, and then
the CMTS will place… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.60 |
| cadSysFlapListInsertionThreshold This object shows the number of seconds between successive ranging
attempts that must pass before the modem is counted as flapped.
The modem must have also been in a provisioning… | scalar | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.61 |
| cadSysAES128Enable Enables AES-128 Cryptography Suite for BPI+ when true. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.62 |
| cadSysCMMAPProcessingTime Time provided between arrival of the last bit of a MAP
at a CM and effectiveness of that MAP. (ref 7.1.1) | scalar | Microseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.7 |
| cadSysCMRangingResponseProcessingTime Minimum tile allowed fro a CM following receipt of a rangin
response before it is expected to reply to an invited ranging
request. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.8 |
| cadSysCMConfiguration Maximum time allowed for a CM, following receipt of a
configuration file, to send a Registration Request to a CMTS. | scalar | Seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.9 |