cadSysPercentAddtlDsBwAllocated
CADANT-CMTS-SYSTEM-MIB ·
.1.3.6.1.4.1.4998.1.1.5.1.1.32
Object
scalar
r/w
Integer32
This value of this setting is used to make a percentage increase to a dynamic downstream service flows maximum traffic rate. This is flexiblity actually causes the E6000 to operate outside the DOCSIS 1.1 specification by allocating and allowing more traffic than was actually requested. The initial reason for providing this capability is to mask problems produced in the Voice environment where devices have been seen to violate the traffic rates. Examples of this are MTAs that overuse the QI bit for long durations thus overdriving the downstream burst interval and the Neura IPDT gateway introducing an additional 0.5% inband signaling to the DS voice flow
Context
- MIB
- CADANT-CMTS-SYSTEM-MIB
- OID
.1.3.6.1.4.1.4998.1.1.5.1.1.32- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- cadSysParams
- Siblings
- 56
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-5
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cadSysSyncInterval Nominal time between transmission of SYNC messages. (ref 6.3.2) | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.1 |
| cadSysT5Timeout Wait for Upstream CHannel Change response. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.10 |
| cadSysT6Timeout Wait for REG-RSP and REG-ACK | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.11 |
| cadSysMiniSlotSize Size of mini-slotfor upstream transmission. Must be a
power of 2 (in units of the Timebase Tick). | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.12 |
| cadSysDSxRequestRetries Number of Timeout Retries on DSA/DSC/DSD Requests. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.13 |
| cadSysDSxResponseRetries Number of Timeout Retries on DSA/DSC/DSD Responses. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.14 |
| cadSysT7Timeout Wait for DSA/DSC/DSD Response timeout. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.15 |
| cadSysT8Timeout Wait for DSA/DSC/DSD Acknowledge timeout. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.16 |
| cadSysT9Timeout Registration timeout, the time allowed between the CMTS
sending a RNG-RSP(success) to a CM, and receiving a
REG-REQ from that same CM. | scalar | Minutes Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.17 |
| cadSysT10Timeout Wait for Transaction End timeout. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.18 |
| cadSysT11Timeout Wait for a DCC Response on the old channel. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.19 |
| cadSysUCDInterval Time between transmission of UCD messages. (ref 6.3.3) | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.2 |
| cadSysT13Timeout Maximum holding time for QOS resources for DCC. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.20 |
| cadSysDCCREQRetries Number of retries on Dynamic Channel Change Request. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.21 |
| cadSysMICEnable Enable MIC checking on the CMTS. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.22 |
| cadSysMICAuthString Encrypted MIC Authentication | scalar | OctetString | .1.3.6.1.4.1.4998.1.1.5.1.1.23 |
| cadSysAutoRecoveryEnable Enable automatic recovery of card/port/software in case
of component failure. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.24 |
| cadSysActiveIpAddress Ip Address of the active control complex. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4998.1.1.5.1.1.25 |
| cadSysSpOperMode Special operational mode. Value of 1 indicates the mode is enabled.
dqossf10cms - Allow 1.0 CMs to be stored in DocsQosServiceFlowEntry
adjrxpwrctl - Allow rx power control to be… | scalar | Bits | .1.3.6.1.4.1.4998.1.1.5.1.1.26 |
| cadSysCountsCollectionRate The period, in minutes, in which every count in the CMTS
is to be collected. If this object is set to 0, counts
collection will be disabled. | scalar | Unsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.27 |
| cadSysMaxQoSActiveTimeout Defines the maximum QoS Active Timeout the E6000 is willing to allow. If
a larger value is received in a CM request the E6000 will return this value
instead in the response (Refe… | scalar | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.28 |
| cadSysMaxQoSAdmittedTimeout Defines the maximum QoS Admitted Timeout the E6000 is willing to allow. If
a larger value is received in a CM request the E6000 will return this value
instead in the response (Re… | scalar | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.29 |
| cadSysMaxMAPPending The number of mini-slots that a CMTS is allowed to map
into the future. (ref 6.3.4) | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.3 |
| cadSysAllow10CmConcatenation Defines whether or not the E6000 will allow a modem operating in DOCSIS 1.0
mode to utilize concatenation. If this value is false and a modem operating
in 1.0 mode sends up a mo… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.30 |
| cadSysAllow10CmFragmentation Defines whether or not the E6000 will allow a modem operating in DOCSIS 1.0
mode to utilize fragmentation. If this value is false and a modem operating
in 1.0 mode sends up a mo… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.31 |
| cadSysMaxTrafBurstFor11CMs This is the default value that will be used to populate the Maximum Traffic Burst
for a 1.1 modem unless the maximum traffic burst TLV is explicitly provided in either
the modems … | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.33 |
| cadSysFanSpeedControlEnable obsolete Enable automatic fan speed control. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.34 |
| cadSysFlaplistPowerAdjustThreshold The threshold is used to monitor the power adjust in the flap
list. For a range request received that results in a power adjust
exceeding the threshold value will cause the count… | scalar | dB Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.35 |
| cadSysRemoteFSEnable Indicates whether the active SCM should allow mounting the
the filesystems of the standby SCM. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.36 |
| cadSysRemotePortEnable Indicates whether the active SCM should allow redirection of
the serial console of the standby SCM. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.37 |
| cadSysTcpSmoothingValue1D8U TCP smoothing value to be programmed into hardware on 1D8U CAMs. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.38 |
| cadSysTcpSmoothingValue2D12U TCP smoothing value to be programmed into hardware on 2D12U CAMs. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.39 |
| cadSysRangingInterval Time between transmission of broadcast Ranging requests. (ref 7.3.3) | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.4 |
| cadSysModemLossThreshold deprecated Minimum modem threshold triggering detection of an
upstream channel lockup. | scalar | Unsigned32 | .1.3.6.1.4.1.4998.1.1.5.1.1.40 |
| cadSysPeakTrafRateFor11CMs obsolete This is the default value that will be used to populate the Peak Traffic Rate
for a 1.1 modem configuration file unless the peak traffic rate is explicitly
provided by a Service C… | scalar | DOCS-QOS3-MIBBitRate | .1.3.6.1.4.1.4998.1.1.5.1.1.41 |
| cadSysCpeHostAuthorization This variable enables the CPE Host Authorization feature. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.44 |
| cadSysMaxUcdBurstLength This variable limits the maximum UCD burst length. | scalar | bytes Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.46 |
| cadSysLO1LeakDetect This variable controls LO1 leak detection on the DMM. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.47 |
| cadMtcmConditionalOverride If set to 'true', for a MAC Domain configured for MTCM enabled operation,
the E6000 will set a registering MTCM-capable CM to be MTCM disabled (via REG-RSP message)
unless at le… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.48 |
| cadSysDelayedCpeLearning This setting only applies to modems that have BPI enabled.
When set to false(2), CPE learning is enabled during registration
when BPI initialization is initiated for those mode… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.49 |
| cadSysInvitedRangingRetries Number of retries on inviting ranging requests. (ref 9.2.4) | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.5 |
| cadSysModPriDsInRccEnabled Enable modifying primary Downstream channel in RCC of Reg-Rsp-MP.
Refer ECN 690. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.52 |
| cadSysSendTccRefIdPerFragment Settings for sending the Transmit Channel Configuration (TCC) Reference sub-type 46.1 for type 46 TCC fragmentation.
If 'true', sends 46.1 Ref ID in every type 46 TCC fragment;
If… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.53 |
| cadSysPeakTrRateUpstream This object enables support for Peak Traffic Rate in the upstream direction. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.54 |
| cadSysAllowAmbiguityOverride This object enables ambiguity resolution channel-override actions. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.55 |
| cadSysUnicastNpUsAcquisition This object enables unicast non-primary upstream channel acquisition. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.56 |
| cadSysMacMoveBlockedOnRcptDhcpPkt MAC movement is blocked on receipt of DHCP packets | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.57 |
| cadSysTftpProxy This parameter provides a global enable for the TFTP
Enforce and Dynamic Shared Secret features. In order for
the cadIfMacDomainTftpEnforce and cadIfMacDomainDynamicSecret
paramet… | scalar | Enumeration | .1.3.6.1.4.1.4998.1.1.5.1.1.58 |
| cadSysFanSpeedLevel Set the fan speed for the chassis. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.59 |
| cadSysRegistrationRequestRetries Number of retries on registration requests/responses. | scalar | Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.6 |
| cadSys1x1onCmAcPwrLossEnabled This object enables/disables the CMTS reaction to a AC Power Loss CM-STATUS.
If true, the CMTS will wait until cadSys1x1onCmAcPwrLossHoldoff expires, and then
the CMTS will place… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.60 |
| cadSysFlapListInsertionThreshold This object shows the number of seconds between successive ranging
attempts that must pass before the modem is counted as flapped.
The modem must have also been in a provisioning… | scalar | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.61 |
| cadSysAES128Enable Enables AES-128 Cryptography Suite for BPI+ when true. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.5.1.1.62 |
| cadSysCMMAPProcessingTime Time provided between arrival of the last bit of a MAP
at a CM and effectiveness of that MAP. (ref 7.1.1) | scalar | Microseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.7 |
| cadSysCMRangingResponseProcessingTime Minimum tile allowed fro a CM following receipt of a rangin
response before it is expected to reply to an invited ranging
request. | scalar | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.8 |
| cadSysCMConfiguration Maximum time allowed for a CM, following receipt of a
configuration file, to send a Registration Request to a CMTS. | scalar | Seconds Integer32 | .1.3.6.1.4.1.4998.1.1.5.1.1.9 |